HMC370LP4

HMC370LP4 / 370LP4E v04.0110 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Typical Applications Features Output Power: 0 dBm Sub-Harmonic Suppression: >22 dBc SSB Phase Noise: -140 dBc/Hz Single Supply: +5V @ 55 mA 24 Lead 4x4 mm SMT Package: 16 mm2 7 FREQ. MULTIPLIERS - ACTIVE - SMT The HMC370LP4(E) is ideal for: • Point-to-Point & VSAT Radios • Fiber Optic • Military Functional Diagram General Description The HMC370LP4(E) is an active miniature x4 frequency multiplier utilizing InGaP GaAs HBT technology in a 4x4 mm leadless surface mount package. Power output is 0 dBm typical from a 5V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >22 dBc typical with respect to output signal level. The low additive SSB phase noise of -140 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC370LP4(E) are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. Electrical Specifi cations, TA = +25° C, Vcc = 5V Parameter Frequency Range, Input Frequency Range, Output Input Power Range Output Power Sub-Harmonic Suppression Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Icc) Pin = 0 dBm -15 -4 0 22 18 7 -140 55 73 Min. Typ. 3.6 - 4.1 14.4 - 16.4 +5 Max. Units GHz GHz dBm dBm dBc dB dB dBc/Hz mA 7 - 46 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC370LP4 / 370LP4E v03.0907 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Output Power vs. Temperature @ -10 dBm Drive Level 4 3 Output Power vs. Drive Level 4 3 7 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm OUTPUT POWER (dBm) 1 0 -1 -2 -3 -4 -5 -6 14 14.4 14.8 15.2 15.6 16 16.4 16.8 +25 C +85 C -40 C OUTPUT POWER (dBm) 2 2 1 0 -1 -2 -3 -4 -5 -6 14 14.4 14.8 15.2 15.6 16 16.4 16.8 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level 4 3 OUTPUT POWER (dBm) 2 1 0 -1 -2 -3 -4 -5 -6 14 14.4 14.8 15.2 15.6 16 16.4 16.8 OUTPUT FREQUENCY (GHz) Vcc=4.5V Vcc=5.0V Vcc=5.5V Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 -40 0 1 2 3 4 5 6 +25 C +85 C -40 C FREQUENCY (GHz) Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 +25 C +85 C -40 C -25 8 9 10 11 12 13 14 15 16 17 18 FREQUENCY (GHz) F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 47 FREQ. MULTIPLIERS - ACTIVE - SMT HMC370LP4 / 370LP4E SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT SSB Phase Noise Performance, Fout= 15.0 GHz 0 -20 v03.0907 Output Spectrum SSB PHASE NOISE (dBc/Hz) 7 OUTPUT POWER (dBm) 10 0 -10 -20 -30 -40 -50 -60 0 2 4 6 8 10 12 14 16 18 20 22 24 26 -40 -60 -80 Pin = 0 dBm Pin = -10 dBm FREQ. MULTIPLIERS - ACTIVE - SMT -100 -120 -140 -160 10 2 10 3 10 4 10 5 10 6 10 7 FREQUENCY (GHz) OFFSET FREQUENCY (Hz) 7 - 48 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC370LP4 / 370LP4E SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Typical Supply Current vs. Vcc Vcc (V) 4.5 5.0 5.5 Icc (mA) 54 55 v03.0907 Absolute Maximum Ratings RF Input (Vcc = +5V) Vcc Channel Temperature Continuous Pdiss (T=85 °C) (derate 8.1 mW/°C above 85 °C) Thermal Resistance (Rth) (junction to ground paddle) Storage Temperature Operating Temperature +20 dBm +5.5V 135 °C 530 mW 123.6 °C/W -65 to +150 °C -40 to +85 °C 7 FREQ. MULTIPLIERS - ACTIVE - SMT 7 - 49 57 Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC370LP4 HMC370LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H370 XXXX H370 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC370LP4 / 370LP4E SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT v03.0907 Pin Description 7 FREQ. MULTIPLIERS - ACTIVE - SMT Pin Number 1, 2, 5-14, 17, 18, 20-24 Function Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Interface Schematic N/C 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RF IN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. 16 RFOUT Multiplied Output. AC coupled. No external DC blocks necessary. 19 Vcc Supply voltage 5V ± 0.5V. 7 - 50 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC370LP4 / 370LP4E SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT Evaluation PCB v03.0907 7 FREQ. MULTIPLIERS - ACTIVE - SMT List of Materials for Evaluation PCB 106137 [1] Item J1 - J3 C1 U1 PCB [2] Description PCB Mount SMA Connector 1,000 pF Capacitor, 0603 Pkg. HMC370LP4(E) x4 Active Multiplier 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 51