HMC380QS16GE

HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Typical Applications The HMC380QS16G / HMC380QS16GE is ideal for: • GSM, GPRS & EDGE Infrastructure Features +19 dBm Input IP3 Low LO Drive: -5 dBm Conversion Gain: 11 dB Noise Figure: 9 dB Single Positive Supply: +5V, 165 mA 8 MIXERS - DOWNCONVERTERS - SMT • CDMA, WCDMA Infrastructure • PHS Infrastructure Functional Diagram General Description The HMC380QS16G & HMC380QS16GE are high linearity down-converter receiver ICs suitable for PCS/UMTS infrastructure applications from 1.7 - 2.2 GHz. The receiver IC is designed to support UMTS applications where a high third order intercept point is required. A passive mixer coupled with a high dynamic range IF amplifier achieves an input IP3 of +19 dBm. The converter provides a gain of 11.5 dB and 9 dB typical single side band noise figure. The IC operates from a positive +5V rail consuming 165 mA of current while only requiring a -5 dBm LO drive. The design requires no external baluns. The mixer supports IF frequencies between 50 MHz and 300 MHz. Electrical Specifi cations, TA = +25° C, LO = -5 dBm, Vdd = 5V, IF = 250 MHz [1] Parameter Frequency Range, RF Frequency Range, LO Frequency Range, IF [2] Conversion Gain Noise Figure (SSB) LO to RF Isolation LO to IF Isolation RF to IF Isolation IP3 (Input) 1 dB Compression (Input) LO Input Drive Level (Typical) Supply Current (Idd for LO & IF) (IF bias resistor= 3.3 Ohms) 20 22 38 17 3 9 Min. Typ. 1.7 - 2.0 1.4 - 1.95 50 - 300 11.5 9.2 25 32 50 19 5 -5 to 0 175 10.5 23 30 46 17 3 9 Max. Min. Typ. 2.0 - 2.2 1.7 - 2.15 50 - 300 11.5 10 28 38 54 19 6 -5 to 0 175 11.5 Max. Units GHz GHz MHz dB dB dB dB dB dBm dBm dBm mA [1] Unless otherwise noted all measurements with low side LO & IF = 250 MHz. [2] If matching must be tuned for optimal results, see application circuit herein. 8 - 62 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Conversion Gain vs. Temperature 15 Isolation 0 -10 ISOLATION (dB) -20 -30 RF TO IF LO TO RF LO TO IF CONVERSION GAIN (dB) 13 11 8 MIXERS - DOWNCONVERTERS - SMT 8 - 63 9 +25 C +85 C -40 C -40 -50 -60 7 5 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 1.6 1.7 1.8 1.9 2 2.1 FREQUENCY (GHz) 2.2 2.3 Conversion Gain vs. LO Drive 15 Return Loss 0 CONVERSION GAIN (dB) 13 RETURN LOSS (dB) -5 11 9 7 LO = -8 dBm LO = -5 dBm LO = -2 dBm LO = 0 dBm -10 RF LO 5 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -15 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Input P1dB vs. Temperature 10 IF Bandwidth 14 10 8 INPUT P1dB (dBm) RESPONSE (dB) 6 2 -2 -6 -10 -14 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 50 150 250 350 IF FREQUENCY (MHz) 450 CONVERSION GAIN RETURN LOSS 6 4 + 25C + 85C - 40C 2 0 1.6 * Unless otherwise noted all measurements with low side LO & IF = 250 MHz. ** If matching must be tuned for optimal results, see application circuit herein. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Input and Output IP3 vs. Temperature 40 OIP3 Input and Output IP3 vs LO Drive 40 OIP3 IP3 (dBm) 20 IP3 (dBm) 8 MIXERS - DOWNCONVERTERS - SMT 30 IIP3 30 IIP3 20 OIP3, LO=-5dBm OIP3, LO=-2dBm OIP3, LO= 0dBm IIP3, LO=-5dBm IIP3, LO=-2dBm IIP3, LO= 0dBm 10 OIP3, +25C OIP3, +85C OIP3, -40C IIP3, +25C IIP3, +85C IIP3, -40C 10 0 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 0 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Noise Figure vs Temperature Swept LO, Fixed IF = 250 MHz 15 + 25C + 85C - 40C Noise Figure Swept IF, Fixed LO = 1.7 GHz 15 13 NOISE FIGURE (dB) 13 NOISE FIGURE (dB) 2.2 2.3 11 11 9 9 7 7 5 1.6 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 5 50 100 150 200 250 300 IF FREQUENCY (MHz) 350 400 Conversion Gain with IF Tuned for 70 MHz 15 IP3 with IF Tuned for 70 MHz 40 INPUT IP3 OUTPUT IP3 CONVERSION GAIN (dB) 13 30 11 IP3 (dBm) 1.7 1.8 1.9 2 2.1 2.2 2.3 20 9 10 7 5 1.6 0 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) FREQUENCY (GHz) * Unless otherwise noted all measurements with low side LO & IF = 250 MHz. ** If matching must be tuned for optimal results, see application circuit herein. 8 - 64 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz MxN Spurious @ IF Port nLO mRF 0 1 2 3 4 0 xx 62 124 126 121 1 40 0 101 126 127 2 60 62 55 113 128 3 58 87 94 76 124 4 35 102 110 112 116 Harmonics of LO nLO Spur @ RF Port LO Freq. (GHz) 1.4 1.6 1.8 2.0 2.2 2.4 1 23 26 26 24 38 23 2 3 6 8 8 10 12 3 16 12 10 12 14 19 4 15 18 29 31 35 40 8 MIXERS - DOWNCONVERTERS - SMT 8 - 65 RF Freq. = 1.9 GHz @ -10 dBm LO Freq. = 1.65 GHz @ -5 dBm All values in dBc relative to the IF power level. LO = -5 dBm All values in dBc below input LO level measured at RF port. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Absolute Maximum Ratings RF / IF Input (Vdd= +5V) LO Drive (Vdd= +5V) +13 dBm +15 dBm +7 Vdc 150°C 1.10 W 59 °C/W -65 to +150°C -40 to +85°C Typical Supply Current vs. Vdd Vdd (LO + IF) +4.5 +5.0 +5.5 Idd (mA) 162 165 168 8 MIXERS - DOWNCONVERTERS - SMT Vdd (LO or IF) Channel Temperature Continuous Pdiss (T = 85°C) (derate 17 mW/°C above 85°C) Thermal Resistance (channel to ground paddle) Storage Temperature Operating Temperature Downconverter will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 6. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1. Package Information Part Number HMC380QS16G HMC380QS16GE Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H380 XXXX H380 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 8 - 66 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Pin Descriptions Pin Number 1, 3, 4, 7, 9, 14, 16 Function N/C Description Not Connected Interface Schematic 8 LO GND Backside of package has exposed metal ground slug that must also be connected to RF/DC ground. 2 11, 12, 13 5 Vdd LO Power supply for the LO amplifier. One external RF bypass capacitor (10,000 pF) is required. 6 Vdd IF Bias voltage for IF amplifier. One external RF bypass capacitor (10,000 pF) is required. 8 IF Bias DC bias setting for IF amplifier. 10 IF Output of IF and bias port for amplifier. A pull up inductor (L1), output matching network (C5, C6, L2), and 10,000 pF bypass capacitor (C4) are required. 15 RF This pin is DC coupled and matched to 50 Ohm from 1.7 - 2.2 GHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 67 MIXERS - DOWNCONVERTERS - SMT This pin is AC coupled and matched to 50 Ohm from 1.4 - 2.2 GHz. HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Evaluation PCB 8 MIXERS - DOWNCONVERTERS - SMT List of Materials for Evaluation PCB 106397 [1] Item J1 - J3 J4 - J6 C1 C2, C3, C4 C5 C6 L1 L2 R1 U1 PCB [2] Description PC Mount SMA RF Connector DC Pins 1000 pF Chip Capacitor, 0603 Pkg. 0.01μF Chip Capacitor, 0603 Pkg. 82 pF Chip Capacitor, 0402 Pkg. 6 pF Chip Capacitor, 0603 Pkg. 150 nH Chip Inductor, 0805 Pkg. 27 nH Chip Inductor, 0805 Pkg. 3.3 Ohm Resistor, 0603 Pkg. HMC380QS16G / HMC380QS16GE 104814 Evaluation Board, 1.100” x 1.100” The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 8 - 68 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC380QS16G / 380QS16GE v02.0305 PCS/UMTS HIGH IP3 RFIC DOWNCONVERTER, 1.7 - 2.2 GHz Application Circuit 8 MIXERS - DOWNCONVERTERS - SMT 8 - 69 Note: Pin 5 and Pin 6 may be connected to a common Vdd Supply. Selection of L2 & C6 For Various Tuned IF Frequencies* IF 250 MHz 70 MHz L2 27 nH 39 nH C6 6 pF 39 pF * Contact Hittite to optimize tuning topology for desired IF frequency. * Unless otherwise noted all measurements with low side LO & IF = 250 MHz. ** If matching must be tuned for optimal results, see application circuit herein. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com