HMC387MS8_08

HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Typical Applications High Dynamic Range Infrastructure: • GSM 450 & GSM 480 • CDMA 450 • Private Land Mobile Radio Features Input IP3: +32 dBm Conversion Loss: 9.5 dB Low External Part Count Ultra Small MSOP8 Package: 14.8 mm2 Included in the HMC-DK003 Designer’s Kit 9 MIXERS - HIGH IP3 - SMT Functional Diagram General Description The HMC387MS8 & HMC387MS8E are high dynamic range passive MMIC mixers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 450 to 500 MHz. Excellent input IP3 performance of +32 dBm for down conversion and +29 dBm for up conversion is provided for both GSM/CDMA based cellular and Private Land Mobile Radio applications at an LO drive of +17 dBm. The mixer also has excellent performance with as little as +13 dBm LO drive yielding a +30 dBm input IP3. With a 1 dB compression of +22 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 9.5 dB typical. The DC to 150 MHz IF frequency response will satisfy many cellular transmit or receive frequency plans. The HMC387MS8(E) input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint and no DC bias. Electrical Specifi cations, TA = +25°C, LO = +17 dBm, IF = 70 MHz [1] Parameter Frequency Range, RF Frequency Range, LO [2] Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) 17 20 29 19 Min. Typ. 450 - 500 300 - 500 DC - 150 9.5 9.5 20 23 32 22 +13 to +19 11 11 Max. Units MHz MHz MHz dB dB dB dB dBm dBm dBm [1] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 70 MHz [2] LO Frequency optimized. See application circuit herein. 9 - 222 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Isolation @ LO = +17 dBm 0 Conversion Gain vs. Temperature @ LO = +17 dBm 0 CONVERSION GAIN (dB) -10 -5 ISOLATION (dB) -20 -10 -30 RF TO IF LO TO RF LO TO IF -15 +25 C +85 C -40 C 9 0.55 0.6 -40 -20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 -50 0.4 0.45 0.5 FREQUENCY (GHz) Conversion Gain vs. LO Drive 0 Return Loss @ LO = +17 dBm 0 -10 RETURN LOSS (dB) -5 -5 -10 -15 LO= +13dBm LO=+ 15dBm LO= +17dBm LO= +19dBm -15 LO RF -20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 -20 0.3 0.35 0.4 0.45 0.5 RF FREQUENCY (GHz) 0.55 0.6 IF Bandwidth @ LO = +17 dBm 0 Upconverter Conversion Gain vs. LO Drive 0 -5 RESPONSE (dB) CONVERSION GAIN RETURN LOSS CONVERSION GAIN (dB) -5 -10 -10 -15 -15 LO = +13 dBm LO = +15 dBm LO = +17 dBm LO = +19 dBm -20 50 100 150 200 250 IF FREQUENCY (MHz) 300 350 -20 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 223 MIXERS - HIGH IP3 - SMT CONVERSION GAIN (dB) HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Input IP3 vs. LO Drive IF = 70 MHz 40 Input IP3 vs. Temperature IF = 70 MHz, LO = +17 dBm 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 30 30 9 MIXERS - HIGH IP3 - SMT 25 +25 C +85 C -40 C 25 LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 Input IP3 vs. LO Drive IF = 97 MHz 40 Input IP3 vs. LO Drive IF = 117 MHz 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 30 30 25 LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm 25 LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 Input IP3 vs. LO Drive IF = 137 MHz 40 Upconverter Input IP3 vs. LO Drive IF = 70 MHz 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 30 30 25 LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm 25 LO= +13 dBm LO= +15 dBm LO= +17 dBm LO= +19 dBm 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 20 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 9 - 224 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Input IP2 vs. Temperature @ LO = +17 dBm 70 65 60 INPUT IP2 (dBm) 55 50 45 40 35 30 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 +25 C +85 C -40 C Input IP2 vs. LO Drive 70 65 60 INPUT IP2 (dBm) 55 50 45 40 35 30 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 LO= +13dBm LO= +15dBm LO= +17dBm LO= +19dBm 9 MIXERS - HIGH IP3 - SMT 9 - 225 Input P1dB vs. Temperature IF = 70 MHz 30 INPUT P1dB (dBm) 25 20 15 +25 C +85 C -40 C 10 0.4 0.45 0.5 0.55 RF FREQUENCY (GHz) 0.6 MxN Spurious Outputs nLO mRF 0 1 2 3 4 0 xx 1.5 54 83 85 1 -5 0 65 77 85 2 13 27 47 85 85 3 13 25 53 74 85 4 6 42 61 70 85 Harmonics of LO nLO Spur @ RF Port LO Freq (GHz) 0.35 0.37 0.39 0.41 0.43 0.45 1 27 26 25 24 23 22 2 37 35 34 33 32 31 3 38 43 44 41 38 37 4 39 39 41 43 44 45 RF Freq = 0.45 GHz @ 0 dBm LO Freq = 0.38 GHz @ +17 dBm All values in dBc relative to the IF output power. LO = +17 dBm All values are in dBc below input LO level @ RF port. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Absolute Maximum Ratings RF/IF Input LO Drive Channel Temperature (Tc) Thermal Resistance Storage Temperature +25 dBm +27 dBm 150 °C 175 °C/W -65 to +150 °C -40 to +85 °C ±40 mA Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 MIXERS - HIGH IP3 - SMT Operating Temperature IF DC Current ESD Sensitivity (HBM) Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC387MS8 HMC387MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H387 XXXX H387 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 9 - 226 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Pin Descriptions Pin Number Function Description This pin is AC coupled & matched to 50 Ohms when an external series inductor (L1) and shunt capacitor (C1) is connected to the LO. Choose values of L1 and C1 to optimize LO frequency response. See Application Circuit herein. Interface Schematic 1 LO 2, 4 N/C Not connected. 9 MIXERS - HIGH IP3 - SMT 9 - 227 3, 6, 7 GND This pin must be connected to RF ground. 5 IF This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of C1 to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF This pin is DC coupled & matched to 50 Ohms from 450 - 500 MHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Evaluation PCB 9 MIXERS - HIGH IP3 - SMT List of Materials for Evaluation PCB 107334 [1] Item J1 - J3 C1 L1 U1 PCB [2] Description PCB Mount SMA RF Connector 4 pF Chip Capacitor, 0603 Pkg 47 nH Chip Inductor, 0805 Pkg HMC387MS8 / HMC387MS8E Mixer 106307 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 [3] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 200 MHz [4] LO Frequency optimized. See application circuit herein. The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 9 - 228 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC387MS8 / 387MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 450 - 500 MHz Application Circuit 9 Selection of L1 & C1 for Optimal LO Frequency ±10% Choose value of L1 & C1 to optimize LO Frequency response. For best results use an 0805 size RF inductor or smaller. LO Frequency (MHz) 400 L1 (nH) 47 C1 (pF) 4 Note: Position L1 and C1 as close to Pin 1 as possible. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 229 MIXERS - HIGH IP3 - SMT