HMC400MS8_08

HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Typical Applications High Dynamic Range Infrastructure: • GSM, GPRS & EDGE • CDMA & W-CDMA • Cable Modem Termination Systems Features Input IP3: +35 dBm Conversion Loss: 8.8 dB No External Components Ultra Small MSOP Package: 14.8mm2 Included in the HMC-DK003 Designer’s Kit 9 MIXERS - HIGH IP3 - SMT Functional Diagram General Description The HMC400MS8(E) is a high dynamic range passive MMIC mixers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 1.7 to 2.2 GHz. Excellent input IP3 performance of +36 dBm for down conversion and +29 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA based UMTS or PCS applications at an LO drive of +17 dBm. With a 1 dB compression of +21 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8.5dB typical and LO isolations are maintained at 22 to 33 dB. This miniature single-ended monolithic GaAs FET mixer does not require any external components or bias. The 50 to 300 MHz IF frequency response will satisfy many UMTS/PCS transmit or receive frequency plans configured for low side LO. The HMC400MS8(E) input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint and no DC bias. Electrical Specifi cations, TA = +25°C, LO = +17 dBm, IF = 200 MHz* Parameter Frequency Range, RF Frequency Range, LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) 29 16 30 18 Min. Typ. 1.7 - 1.8 1.4 - 1.75 DC - 300 9 9 33 20 34 21 +16 to +18 11 11 24 17 32 18 Max. Min. Typ. 1.8 - 2.0 1.5 - 1.95 DC - 300 8.8 8.8 30 22 36 21 +16 to +18 10.5 10.5 20 19 28 18 Max. Min. Typ. 2.0 - 2.2 1.7 - 2.15 DC - 300 8.8 8.8 25 25 32 22 +16 to +18 10.5 10.5 Max. Units GHz GHz MHz dB dB dB dB dBm dBm dBm *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. 9 - 238 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Conversion Gain vs. Temperature @ LO = +17 dBm 0 Isolation @ LO = +17 dBm 0 RF TO IF LO TO RF LO TO IF CONVERSION GAIN (dB) -5 ISOLATION (dB) -10 -10 -20 -15 + 25C + 85C - 40C -30 9 1.8 1.9 2 2.1 FREQUENCY (GHz) 2.2 2.3 -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -40 1.7 Conversion Gain vs. LO Drive 0 Return Loss @ LO = +17 dBm 0 -5 RETURN LOSS (dB) -5 -10 -15 -20 -25 -30 RF LO -10 -15 LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Upconverter Performance Conversion Gain @ LO = +17 dBm 0 If Bandwidth @ LO = +17 dBm 0 CONVERSION GAIN (dB) -5 RESPONSE (dB) -5 -10 -10 -15 -15 CONVERSION GAIN RETURN LOSS -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -20 50 100 150 200 250 300 350 IF FREQUENCY (MHz) 400 450 500 *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 239 MIXERS - HIGH IP3 - SMT CONVERSION GAIN (dB) HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Input IP3 vs. Temperature, LO = +17 dBm 40 Input IP3 vs. IF Frequency, RF = 1.75 GHz 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 30 30 9 MIXERS - HIGH IP3 - SMT 25 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 25 + 25C + 85C - 40C 20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Input IP3 vs. IF Frequency, RF = 1.95 GHz 40 Input IP3 vs. LO Drive 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 30 30 25 LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm 25 + 15dBm + 16dBm + 17dBm + 19dBm 20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Input IP3 vs. IF Frequency, RF = 2.15 GHz 40 Upconverter IP3 vs. LO Drive, IF = 200 MHz 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 35 LO = +15 dBm LO = +16 dBm LO = +17 dBm LO = +19 dBm 30 30 25 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 25 20 60 90 120 150 180 210 240 IF FREQUENCY (MHz) 270 300 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. 9 - 240 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Input IP2 vs. Temperature @ LO = +17 dBm 45 Input IP2 vs. LO Drive @ LO = +17 dBm 45 40 INPUT IP2 (dBm) INPUT IP2 (dBm) 40 35 35 30 + 25C + 85C - 40C 30 + 15 dBm + 16 dBm + 17 dBm + 19 dBm 9 2.2 2.3 25 25 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) Input P1dB vs. Temperature @ LO = +17 dBm 25 MxN Spurious Outputs nLO mRF 0 xx 9 71 79 77 1 -11 0 70 80 80 2 7 24 49 80 80 3 4 31 58 79 79 4 8 27 64 77 80 23 INPUT P1dB (dBm) 0 1 2 21 19 + 25C + 85C - 40C 3 4 17 RF Freq = 2 GHz @ -10 dBm LO Freq = 1.8 GHz @ +17 dBm All values in dBc relative to the IF output power. 2.2 2.3 15 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) Harmonics of LO nLO Spur @ RF Port LO Freq (GHz) 1.4 1.55 1.7 1.85 2 2.15 1 42 33 29 26 24 21 2 26 25 29 31 36 38 3 56 56 49 44 44 43 4 46 53 50 53 48 49 Absolute Maximum Ratings RF/IF Input LO Drive Storage Temperature Operating Temperature IF DC Current +27 dBm +27 dBm -65 to +150 °C -40 to +85 °C ±40 mA ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS LO = +17 dBm All values are in dBc below input LO level @ RF port. *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 241 MIXERS - HIGH IP3 - SMT HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Outline Drawing 9 MIXERS - HIGH IP3 - SMT NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC400MS8 HMC400MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H400 XXXX H400 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 9 - 242 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Pin Descriptions Pin Number Function Description Interface Schematic 1 LO This pin is AC coupled & matched to 50 Ohms from 1.4 to 2.2 GHz. Blocking capacitors are required if line potential is not equal to 0V. 2, 4 N/C Not connected. 9 MIXERS - HIGH IP3 - SMT 9 - 243 3, 6, 7 GND This pin must be connected to RF ground. This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 5 IF Port 8 RF Port This pin is DC coupled & matched to 50 Ohm from 1.7 to 2.2 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Evaluation PCB 9 MIXERS - HIGH IP3 - SMT List of Materials for Evaluation PCB 101830 [1] Item J1 - J3 U1 PCB [2] Description PCB Mount SMA RF Connector HMC400MS8 / HMC400MS8E Mixer 101828 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 9 - 244 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC400MS8 / 400MS8E v02.0705 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Notes: 9 MIXERS - HIGH IP3 - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 245