HMC412MS8G

MICROWAVE CORPORATION v00.0901 HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Features Conversion Loss: 8.0 dB Noise Figure: 8.0 dB Input IP3: 17 dBm No External Components MSOP8G SMT Package Typical Applications The HMC412MS8G is ideal for: • Long Haul Radio Platforms • Microwave Radio • VSAT Functional Diagram General Description The HMC412MS8G is a passive double balanced mixer that operates between 9.0 GHz and 15 GHz. The HMC412MS8G operates with LO drive levels between +9 dBm and +13 dBm, and provides 8 dB conversion loss across the entire specified frequency band. This mixer requires no external components or bias. 12 MIXERS - SMT Electrical Specifications, TA = +25° C Parameter Min. Frequency Range, RF & LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation RF to IF Isolation IP3 (Input) 1 dB Compression (Input) 30 33 8 14 7 IF = 1.45 GHz LO = +13 dBm Typ. 9.0 - 15.0 DC - 2.5 8 8 40 - 50 40 - 50 17 17 9.5 11 11 Max. GHz GHz dB dB dB dB dB dBm dBm Units * Unless otherwise noted, all measurements performed as downconverter, IF= 1.45 GHz. 12 - 236 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.0901 HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Conversion Gain vs. Temperature @ LO = +13 dBm 0 Isolation @ LO = +13 dBm 0 -10 RF/IF LO/RF LO/IF CONVERSION GAIN (dB) -5 ISOLATION (dB) +25 C -40 C +85 C -20 -30 -40 -50 -60 -10 -15 -20 8 9 10 11 12 13 14 15 16 FREQUENCY (GHz) 8 9 10 11 12 13 14 15 16 FREQUENCY (GHz) 12 MIXERS - SMT Conversion Gain vs. LO Drive 0 Return Loss @ LO = +13 dBm 0 CONVERSION GAIN (dB) -5 RETURN LOSS (dB) -5 -10 -10 -15 -15 LO = +7 dBm LO = +9 dBm LO = +11 dBm LO = +13 dBm LO = +15 dBm -20 RF LO -20 8 9 10 11 12 13 14 15 16 FREQUENCY (GHz) -25 8 9 10 11 12 13 14 15 16 FREQUENCY (GHz) IF Bandwidth @ LO = +13 dBm 0 -5 Upconverter Performance Conversion Gain @ LO = +13 dBm 0 CONVERSION GAIN (dB) Conversion Gain Return Loss -5 RESPONSE (dB) -10 -15 -20 -25 -30 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) -10 -15 -20 8 9 10 11 12 13 14 15 16 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 237 MICROWAVE CORPORATION v00.0901 HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Input IP3 vs. LO Drive* 30 LO = +11 dBm LO = +13 dBm LO = +15 dBm Input IP3 vs. Temperature @ LO = +13 dBm* 30 +25 C -40 C +85 C 25 25 IP3 (dBm) 20 IP3 (dBm) 9 10 11 12 13 14 15 16 17 20 15 15 12 MIXERS - SMT 10 FREQUENCY (GHz) 10 9 10 11 12 13 14 15 16 17 FREQUENCY (GHz) Input IP2 vs. LO Drive * 70 Input P1dB vs. Temperature @ LO = +13 dBm 15 14 13 +25 C -40 C +85 C 60 12 P1dB (dBm) LO = +11 dBm LO = +13 dBm LO = +15 dBm IP2 (dBm) 11 10 9 8 50 40 7 6 5 8 9 10 11 12 13 14 15 16 30 9 10 11 12 13 14 15 16 17 FREQUENCY (GHz) FREQUENCY (GHz) MxN Spurious @ IF Port nLO mRF 0 1 2 3 4 0 XX 7 78 >85 N/A 1 16 0 >85 >85 >85 2 27 >85 72 >85 >85 3 38 57 71 78 >85 4 N/A 56 >85 >85 >85 Harmonics of LO nLO Spur @ RF Port LO Freq. (GHz) 9 10.5 12 13.5 15 16.5 1 36 34.8 49.5 48.7 39.2 34 2 30 31.3 44.5 58.8 74.5 61.3 3 58.3 35.7 65.2 69 64 60.3 4 70.5 57.5 68.7 N/A N/A N/A RF = 14.45 GHz @ -10 dBm LO = 13 GHz @ +13 dBm All values in dBc relative to the IF. Measured as downconverter. LO = +13 dBm All values in dBc below input LO level @ RF port. * Two-tone input power= -10 dBm each tone, 1 MHz spacing. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 238 MICROWAVE CORPORATION v00.0901 HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Absolute Maximum Ratings RF / IF Input (Vdd = +3V) LO Drive (Vdd = +3V) IF DC Current Storage Temperature Operating Temperature +27 dBm +27 dBm ±4 mA -65 to +150 °C -55 to +85 °C 12 MIXERS - SMT NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Outline Drawing For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 239 v00.0901 MICROWAVE CORPORATION HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Pin Descriptions Pin Number Function Description Interface Schematic 1, 8 GND Ground: Pin must connect to RF ground. 12 MIXERS - SMT 2 LO Port LO Port: This pin is DC coupled and matched to 50 Ohm from 9.5 - 15.0 GHz. 3, 4, 6 N/C Not Connected 5 IF Port IF Port: This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose values has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 4mA of current or die non-function and possible die failure will result. 7 RF Port RF Port: This pin is AC coupled and matched to 50 Ohm from 9.5 - 15.0 GHz. 12 - 240 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v00.0901 MICROWAVE CORPORATION HMC412MS8G DOUBLE-BALANCED MIXER, 9.0 - 15.0 GHz Evaluation PCB 12 MIXERS - SMT List of Material Item J1 - J2 J3 U1 PCB* Description PC Mount SMA RF Connector, SRI PC Mount SMA Connector, Johnson HMC412MS8G Mixer 101650 Evaluation Board * Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 241