HMC422MS8_10

HMC422MS8 / 422MS8E v03.0710 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.2 - 2.6 GHz Typical Applications The HMC422MS8 / HMC422MS8E is ideal for: • MMDS & ISM Features Integrated LO Amplifier w/ Pdiss 85 >85 1 2 0 60 >85 >85 2 22 27 64 83 >85 3 26 48 53 69 >85 4 41 57 73 80 >85 Harmonics of LO nLO Spur @ RF Port LO Freq. (GHz) 1.5 1.75 2 2.25 2.5 3 1 33 30 29 27 25 22 2 14 16 17 20 26 37 3 38 39 45 50 49 69 4 35 44 47 52 61 72 RF = 2.1 GHz @ -10 dBm LO = 2 GHz @ 0 dBm All values in dBc relative to the IF power level. LO = 0 dBm All values in dBc below input LO level @ RF port. * Two-tone input power= 0 dBm each tone, 1 MHz spacing. 10 - 220 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC422MS8 / 422MS8E v03.0710 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.2 - 2.6 GHz Absolute Maximum Ratings RF / IF Input (Vdd = +3V) LO Drive (Vdd = +3V) Vdd IF DC Current Channel Temperature (Tc) Continuous Pdiss (T = 85°C) (Derate 5.8 mW/°C above 85 C) Storage Temperature Operating Temperature ESD Sensitivity (HBM) +13 dBm +13 dBm +7 Vdc ±10 mA 150 °C 0.38 W -65 to +150 °C -40 to +85 °C Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 - 221 Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC422MS8 HMC422MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H422 XXXX H422 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC422MS8 / 422MS8E v03.0710 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.2 - 2.6 GHz Pin Descriptions Pin Number Function Description Interface Schematic 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT 1 LO This pin is AC coupled and matched to 50 Ohms. 2, 3, 6, 7 GND Pins must connect to RF ground. 4 Vdd Power supply for the LO Amplifier. One external RF bypass capacitor (10,000 pF) is required. 5 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 10 mA of current or die non-function and possible die failure will result. 8 RF This pin is DC coupled and matched to 50 Ohms. 10 - 222 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC422MS8 / 422MS8E v03.0710 GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, 1.2 - 2.6 GHz Evaluation PCB 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 - 223 List of Materials for Evaluation PCB 105188 [1] Item J1 - J3 J4 - J5 C1 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 10k pF Chip Capacitor, 0603 Pkg. HMC422MS8 / HMC422MS8E Mixer 104813 Evaluation PCB, 1.0” x 1.0” [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com