HMC437MS8G

HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Typical Applications Features SSB Phase Noise: -153 dBc/Hz @100KHz Wide Bandwidth Output Power: -1 dBm Single DC Supply: +5V @ 69 mA MS8G SMT Package 4 FREQUENCY DIVIDERS & DETECTORS - SMT Prescaler for DC to C Band PLL Applications: • UNII, Point-to-Point & VSAT Radios • 802.11a & HiperLAN WLAN • Fiber Optic • Cellular / 3G Infrastructure Functional Diagram General Description The HMC437MS8G & HMC437MS8GE are low noise Divide-by-3 Static Dividers utilizing InGaP GaAs HBT technology in low cost 8 lead surface mount plastic packages. This device operates from DC (with a square wave input) to 7 GHz input frequency from a single +5V DC supply. The low additive SSB phase noise of -153 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifi cations, TA = +25° C, 50 Ohm System, Vcc= 5V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Sine Wave Input [1] Fin= 1 to 6 GHz Fin= 6 to 7 GHz Output Power Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) 1. Divider will operate down to DC for square-wave input signal. Both RF Outputs Terminated Pin= 0 dBm, Fin= 6 GHz Pin= 0 dBm, Fout= 882 MHz -12 -10 -4 -1 -50 -153 100 69 Conditions Min. 7.0 Typ. 7.5 0.1 +12 +10 Max. Units GHz GHz dBm dBm dBm dBm dBc/Hz ps mA 4 - 84 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Input Sensitivity Window, T= 25 °C 20 15 INPUT POWER (dBm) Input Sensitivity Window vs. Temperature 20 15 INPUT POWER (dBm) 10 5 0 -5 -10 -15 -20 Min Pin +25 C Max Pin +25 C Min Pin +85 C Max Pin +85 C Min Pin -40 C Max Pin -40 C 4 FREQUENCY DIVIDERS & DETECTORS - SMT 4 - 85 10 5 0 -5 -10 -15 -20 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) Recommended Operating Window 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) Output Power vs. Temperature 4 3 OUTPUT POWER (dBm) 2 1 0 -1 -2 -3 -4 -5 -6 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) +25 C +85 C -40 C SSB Phase Noise Performance, Pin= 0 dBm, Fin= 6 GHz, T= 25 °C 0 SSB PHASE NOISE (dBc/Hz) -30 -60 -90 -120 -150 -180 2 10 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 °C 0 Reverse Leakage, Pin= 0 dBm, T= 25 °C 0 -10 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) OUTPUT LEVEL (dBm) 5 6 7 8 9 -10 -20 -30 -40 -50 -60 -70 -20 -30 Pfeedthru 2nd Harmonic -40 -50 0 1 2 3 4 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 °C 4 FREQUENCY DIVIDERS & DETECTORS - SMT AMPLITUDE (mV) 300 200 100 0 -100 -200 -300 -400 -500 22.5 23 23.5 24 TIME (ns) 24.5 25 25.5 Absolute Maximum Ratings RF Input Power (Vcc = +5V) Nominal +5V Supply to GND Max Peak Flow Temperature Storage Temperature ESD Sensitivity (HBM) 13 dBm -0.3V to +5.5V 260 °C -65 to +125 °C Class 1A Reliability Information Junction Temperature to Maintain 1 Million Hour MTTF Nominal Junction Temperature (T = 85 °C) Thermal Resistance (Junction to GND Paddle, 3V Supply) Operating Temperature 135 °C 122 °C 101.5 °C/W -40 to +85 °C DC blocking capacitors are required at RF input and RF output ports. Choose value for lowest frequency of operation. Typical Supply Current vs. Vcc Vcc (V) 4.75 Icc (mA) 64 69 75 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 5.0 5.25 Note: Divider will operate over full voltage range shown above 4 - 86 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Outline Drawing 4 FREQUENCY DIVIDERS & DETECTORS - SMT 4 - 87 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC437MS8G HMC437MS8GE Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H437 XXXX H437 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Pin Description Pin Number 1 Function Vcc Description Supply voltage 5V ± 0.25V. Interface Schematic 2 IN RF input must be DC blocked. 3 IN RF input 180° out of phase with pin 2 for differential operation. AC ground for single ended operation. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Pin Description (Continued) 4 FREQUENCY DIVIDERS & DETECTORS - SMT Pin Number Function Description All ground leads and ground paddle must be soldered to PCB RF/DC ground. Interface Schematic 4, 5 GND 6 OUT Divided output 180° out of phase with pin 7. 7 OUT Divided Output. 8 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Application Circuit 4 - 88 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC437MS8G / 437MS8GE v04.0410 SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7 GHz Evaluation PCB 4 FREQUENCY DIVIDERS & DETECTORS - SMT 4 - 89 List of Materials for Evaluation PCB 105786 [1] Item J1 - J3 J4, J5 C1 - C4 C5 C6 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 pF Capacitor, 0402 Pkg. 10,000 pF Capacitor, 0603 Pkg. 4.7 μF Tantalum Capacitor HMC437MS8G / HMC437MS8GE Divide-by-3 105697 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. This evaluation board is designed for single ended input testing. J2 and J3 provide differential output signals. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com