HMC444LP4

HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT v03.0907 Typical Applications Active Multiplier for X Band Applications: • Fiber Optic Features Output Power: +6 dBm Sub-Harmonic Suppression: >25 dBc SSB Phase Noise: -136 dBc/Hz Single Supply: +5V@ 68 mA 24 Lead 4x4 mm SMT Package: 16 mm2 7 FREQUENCY MULTIPLIERS - SMT • Point-to-Point Radios • Military Radar Functional Diagram General Description The HMC444LP4 & HMC444LP4E are active miniature x8 frequency multipliers utilizing InGaP GaAs HBT technology in 4x4 mm leadless surface mount packages. Power output is +6 dBm typical from a 5.0V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >25 dBc typical with respect to output signal level. The low additive SSB phase noise of -136 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC444LP4 & HMC444LP4E are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. Electrical Specifi cations, TA = +25° C, Vcc= 5.0V Parameter Frequency Range, Input Frequency Range, Output Input Power Range Output Power Sub-Harmonic Suppression Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Icc) Pin= 0 dBm -15 3 6 25 22 7 -136 68 91 Min. Typ. 1.2375 - 1.40 9.9 - 11.2 +5 Max. Units GHz GHz dBm dBm dBc dB dB dBc/Hz mA 7 - 58 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT Output Power vs. Temperature @ -10 dBm Drive Level 10 9 OUTPUT POWER (dBm) OUTPUT POWER (dBm) 8 7 6 5 4 3 2 1 0 9.6 10 10.4 10.8 11.2 11.6 +25 C +85 C -40 C v03.0907 Output Power vs. Drive Level 10 9 8 7 6 5 4 3 2 1 0 9.6 10 10.4 10.8 11.2 11.6 7 FREQUENCY MULTIPLIERS - SMT 7 - 59 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level 10 9 OUTPUT POWER (dBm) 8 Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 +25 C +85 C -40 C 7 6 5 4 3 2 1 0 9.6 10 10.4 10.8 11.2 11.6 Vcc=4.5V Vcc=5.0V Vcc=5.5V 0 0.5 1 1.5 2 2.5 3 OUTPUT FREQUENCY (GHz) FREQUENCY (GHz) Output Return Loss vs. Temperature 0 RETURN LOSS (dB) -5 -10 -15 +25 C +85 C -40 C -20 8 9 10 11 12 13 14 15 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT SSB Phase Noise Performance, Fout= 10.5 GHz 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 2 10 SSB PHASE NOISE (dBc/Hz) v03.0907 Output Spectrum 10 0 7 FREQUENCY MULTIPLIERS - SMT OUTPUT POWER (dBm) -10 -20 -30 -40 -50 -60 0 2 4 6 8 10 12 14 16 18 20 22 24 26 FREQUENCY (GHz) Pin= 0dBm Pin= -10dBm 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) 7 - 60 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT v03.0907 Absolute Maximum Ratings RF Input (Vcc= +5V) Vcc Channel Temperature Continuous Pdiss (T=85 °C) (derate 10 mW/°C above 85 °C) Thermal Resistance (Rth) (junction to ground paddle) Storage Temperature Operating Temperature +20 dBm +6V 150 °C 650 mW 100 °C/W -65 to +150 °C -40 to +85 °C Typical Supply Current vs. Vcc Vcc (V) 4.5 5.0 5.5 Icc (mA) 66 68 70 7 FREQUENCY MULTIPLIERS - SMT 7 - 61 Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC444LP4 HMC444LP4E Package Body Material Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H444 XXXX H444 XXXX RoHS-compliant Low Stress Injection Molded Plastic [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT v03.0907 Pin Description Pin Number 1, 2, 5-14, 17, 18, 20-24 Function N/C Description No Connection Interface Schematic 7 FREQUENCY MULTIPLIERS - SMT 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RF IN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. Multiplied Output. AC coupled. No external DC blocks necessary. 16 RFOUT 19 Vcc Supply voltage 5V ± 0.5V. 7 - 62 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC444LP4 / 444LP4E SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT v03.0907 Evaluation PCB 7 FREQUENCY MULTIPLIERS - SMT List of Materials for Evaluation PCB 106137 [1] Item J1 - J3 C1 U1 PCB [2] Description PCB Mount SMA Connector 1,000 pF Capacitor, 0603 Pkg. HMC444LP4 / HMC444LP4E x16 Active Multiplier 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 63