HMC445LP4E

HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT Typical Applications Active Multiplier for X Band Applications: • Fiber Optic • Point-to-Point Radios • Military Radar v04.0210 Features Output Power: +7 dBm Sub-Harmonic Suppression: >25 dBc SSB Phase Noise: -130 dBc/Hz Single Supply: 5V @ 78 mA 24 Lead 4x4 mm SMT Package: 16 mm2 5 Functional Diagram General Description The HMC445LP4 & HMC445LP4E are active miniature x16 frequency multipliers utilizing InGaP GaAs HBT technology in 4x4 mm leadless surface mount packages. Power output is +7 dBm typical from a 5V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >25 dBc typical with respect to output signal level. The low additive SSB phase noise of -130 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC445LP4 & HMC445LP4E are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. FREQ. MULTIPLIERS - ACTIVE - SMT Electrical Specifi cations, TA = +25° C, Vcc= 5V Parameter Frequency Range, Input Frequency Range, Output Input Power Range Output Power Sub-Harmonic Suppression Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Icc) Pin= 0 dBm -15 4 7 25 28 7 -130 78 104 Min. Typ. 618.75 - 687.50 9.9 - 11.0 5 Max. Units MHz GHz dBm dBm dBc dB dB dBc/Hz mA 5 - 54 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT Output Power vs. Temperature @ -10 dBm Drive Level 0 v04.0210 Output Power vs. Drive Level 10 9 RETURN LOSS (dB) -5 OUTPUT POWER (dBm) 8 7 6 5 4 3 2 1 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm -10 -15 +25 C +85 C -40 C 5 11.2 11.6 -20 8 9 10 11 12 13 14 15 FREQUENCY (GHz) 0 9.6 10 10.4 10.8 OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level 10 9 OUTPUT POWER (dBm) 8 7 6 5 4 3 2 1 0 9.6 10 10.4 10.8 11.2 11.6 Vcc=4.5V Vcc=5.0V Vcc=5.5V Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 -40 0 0.5 1 1.5 2 2.5 3 +25 C +85 C -40 C OUTPUT FREQUENCY (GHz) FREQUENCY (GHz) Output Return Loss vs. Temperature 0 RETURN LOSS (dB) -5 -10 -15 +25 C +85 C -40 C -20 8 9 10 11 12 13 14 15 FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 5 - 55 FREQ. MULTIPLIERS - ACTIVE - SMT HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT SSB Phase Noise Performance, Fout= 10.5 GHz 0 SSB PHASE NOISE (dBc/Hz) -20 -40 -60 -80 -100 -120 -140 -160 2 10 3 4 5 6 7 v04.0210 Output Spectrum 10 0 OUTPUT POWER (dBm) -10 -20 -30 -40 -50 Pin= 0dBm Pin= -10dBm 5 FREQ. MULTIPLIERS - ACTIVE - SMT -60 0 2 4 6 8 10 12 14 16 18 20 22 24 26 FREQUENCY (GHz) 10 10 10 10 10 OFFSET FREQUENCY (Hz) 5 - 56 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT v04.0210 Absolute Maximum Ratings RF Input (Vcc = +5V) Vcc Channel Temperature Continuous Pdiss (T=85 °C) (derate 11.5 mW/°C above 85 °C) Thermal Resistance (Rth) (junction to ground paddle) Storage Temperature Operating Temperature +20 dBm +5.5V 135 °C 750 mW 87.2 °C/W -65 to +150 °C -40 to +85 °C Typical Supply Current vs. Vcc Vcc (V) 4.5 5.0 5.5 Icc (mA) 75 78 80 Note: Multiplier will operate over full voltage range shown above. 5 FREQ. MULTIPLIERS - ACTIVE - SMT 5 - 57 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED Package Information Part Number HMC445LP4 HMC445LP4E Package Body Material Low Stress Injection Molded Plastic LAND PATTERN. Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H445 XXXX H445 XXXX RoHS-compliant Low Stress Injection Molded Plastic [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT v04.0210 Pin Description Pin Number 1, 2, 5 - 14, 17, 18, 20 - 24 Function N/C Description The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Interface Schematic 5 FREQ. MULTIPLIERS - ACTIVE - SMT 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RF IN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. Multiplied Output. AC coupled. No external DC blocks necessary. 16 RFOUT 19 Vcc Supply voltage 5V ± 0.5V. 5 - 58 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC445LP4 / 445LP4E SMT GaAs HBT MMIC x16 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.0 GHz OUTPUT Evaluation PCB v04.0210 5 FREQ. MULTIPLIERS - ACTIVE - SMT 5 - 59 List of Materials for Evaluation PCB 106137 [1] Item J1 - J3 C1 U1 PCB [2] Description PCB Mount SMA Connector 1,000 pF Capacitor, 0603 Pkg. HMC445LP4 / HMC445LP4E x16 Active Multiplier 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com