HMC545E

HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Typical Applications The HMC545 / HMC545E is ideal for: • Cellular/3G Infrastructure • Private Mobile Radio Handsets • WLAN, WiMAX & WiBro • Automotive Telematics • Test Equipment Features Low Insertion Loss: 0.25 dB High Input IP3: +65 dBm Low DC Power Consumption Positive Control: 0/+3V to 0/+8V Ultra Small Package: SOT26 Functional Diagram General Description The HMC545 and HMC545E are low-cost SPDT switches in 6-lead SOT26 plastic packages for use in general switching applications which require very low insertion loss and very small size. With 0.25 dB typical loss, these devices can control signals from DC to 3.0 GHz and are especially suited for IF and RF applications including Cellular/3G, ISM, automotive and portables. The design provides exceptional insertion loss performance, ideal for filter and receiver switching. RF1 and RF2 are reflective shorts when “Off”. The two control voltages require a minimal amount of DC current and offer compatibility with CMOS and some TTL logic families. 10 SWITCHES - SMT Electrical Specifi cations TA = +25° C, Vctl = 0/+5 Vdc (Unless Otherwise Stated), 50 Ohm System Parameter Insertion Loss Frequency DC - 1.0 GHz DC - 2.5 GHz DC - 3.0 GHz DC - 2.2 GHz DC - 2.5 GHz DC - 3.0 GHz DC - 1.0 GHz DC - 2.0 GHz DC - 2.5 GHz DC - 3.0 GHz Vctl = 0/+3V Vctl = 0/+5V Vctl = 0/+8V Vctl = 0/+3V Vctl = 0/+5V Vctl = 0/+8V 0.5 - 3.0 GHz 23 29 32 26 22 20 Min. Typ. 0.25 0.3 0.4 31 27 24 25 21 19 17 27 33 36 45 65 65 Max. 0.4 0.5 0.7 Units dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBm dBm dBm Isolation Return Loss Input Power for 1 dB Compression Input Third Order Intercept (Two-tone Input Power = +17 dBm Each Tone) Switching Characteristics 0.5 - 3.0 GHz DC - 3.0 GHz tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 70 90 ns ns 10 - 306 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Insertion Loss 0 Return Loss 0 -5 INSERTION LOSS (dB) RETURN LOSS (dB) -0.5 -10 -15 -20 -25 -30 -35 RFC RF1, RF2 ON -1 -1.5 +25 C +85 C -40 C -2 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) -40 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) 10 SWITCHES - SMT 10 - 307 Isolation Between Ports RFC and RF1/RF2 0 -5 -10 ISOLATION (dB) -15 -20 -25 -30 -35 -40 -45 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) RF1 RF2 Isolation Between Ports RF1 and RF2 0 -5 -10 ISOLATION (dB) -15 -20 -25 -30 -35 -40 -45 0 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) RF1 ON RF2 ON Input P0.1dB vs. Vctl 40 35 INPUT P0.1dB (dBm) Input P1dB vs. Vctl 40 35 INPUT P1dB (dBm) 30 25 20 15 10 5 0 +3V +5V +8V 30 25 20 15 10 5 0 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) +3V +5V +8V 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Low Frequency Input P0.1dB vs. Vctl 40 35 INPUT P0.1dB (dBm) 30 25 20 15 10 0.01 +3V +5V +8V Low Frequency Input P1dB vs. Vctl 40 35 INPUT P1dB (dBm) 30 25 20 15 10 0.01 +3V +5V +8V 0.1 FREQUENCY (GHz) 1 0.1 FREQUENCY (GHz) 1 10 SWITCHES - SMT 75 70 65 INPUT IP3 (dBm) 60 55 50 45 Input Third Order Intercept Point vs. Control Voltage Absolute Maximum Ratings RF Input Power (Vctl = 0/+8V) Control Voltage Range (A & B) Hot Switch Power Level (Vctl = 0/+8V) Channel Temperature Continuous Pdiss (T= 85 °C) (derate 3.5 mW/ °C above 85°C) Thermal Resistance +34 dBm -0.2 to +12 Vdc +32 dBm 150 °C 0.23 W 282 °C/W -65 to +150 °C -40 to +85 °C Class 1A 40 35 30 0.5 +3V +5V +8V Storage Temperature Operating Temperature 1 1.5 2 2.5 3 ESD Sensitivity (HBM) FREQUENCY (GHz) DC blocks are required at ports RFC, RF1 and RF2. Insertion Loss, T = +25 °C 0 -0.05 INSERTION LOSS (dB) -0.1 -0.15 -0.2 -0.25 -0.3 -0.35 -0.4 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Truth Table Control Input A Low High B High Low Control Current RFC to RF1 Off On RFC to RF2 On Off Control Voltages State Low High Bias Condition 0 to 0.2 Vdc @ 1 µA Typical +3 Vdc @ 0.5 µA Typical to +8 Vdc @ 3 µA Typical (±0.2 Vdc) 10 - 308 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Outline Drawing 10 SWITCHES - SMT 10 - 309 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC545 HMC545E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking H545 545E [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Typical Application Circuit 10 SWITCHES - SMT Notes: 1. Set logic gate Vdd = +3V to +5V and use HCT series logic to provide a TTL driver interface. 2. Control inputs A/B can be driven directly with CMOS logic (HC) with Vdd of +3V to +8V applied to the CMOS logic gates. 3. DC Blocking capacitors are required for each RF port as shown. Capacitor value determines lowest frequency of operation. 4. Highest RF signal power capability is achieved with Vdd = +8V and A/B set to 0/+8V. Pin Descriptions Pin Number 1, 3, 5 Function RF2, RF1, RFC Description These pins are DC coupled and matched to 50 Ohms. Blocking capacitors are required. Interface Schematic 2 GND This pin must be connected to RF/DC ground. 4 B See truth and control voltage tables. 6 A See truth and control voltage tables. 10 - 310 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC545 / 545E v00.0905 GaAs MMIC SPDT SWITCH, DC - 3 GHz Evaluation PCB 10 SWITCHES - SMT List of Materials for Evaluation PCB 101675 [1] Item J1 - J5 J6 - J8 C1 - C5 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 330 pF capacitor, 0402 Pkg. HMC545 / HMC545E SPDT Switch 101659 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 311