HMC564LC4_09

HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Features Noise Figure: 1.8 dB Gain: 17 dB OIP3: 25 dBm Single Supply: +3V @ 51 mA 50 Ohm Matched Input/Output 8 LOW NOISE AMPLIFIERS - SMT Typical Applications The HMC564LC4 is ideal for use as a LNA or driver amplifier for: • Point-to-Point Radios • Point-to-Multi-Point Radios & VSAT • Test Equipment and Sensors • Military & Space RoHS Compliant 4 x 4 mm Package Functional Diagram General Description The HMC564LC4 is a high dynamic range GaAs PHEMT MMIC Low Noise Amplifier housed in a leadless RoHS compliant 4x4mm SMT package. Operating from 7 to 14 GHz, the HMC564LC4 features extremely flat small signal gain of 17 dB as well as 1.8 dB noise figure and +25 dBm output IP3 across the operating band. This self-biased LNA is ideal for microwave radios due to its consistent output power, single +3V supply operation, and DC blocked RF I/O’s. Electrical Specifi cations, TA = +25° C, Vdd 1, 2 = +3V Parameter Frequency Range Gain Gain Variation Over Temperature Noise Figure Input Return Loss Output Return Loss Output Power for 1 dB Compression (P1dB) Saturated Output Power (Psat) Output Third Order Intercept (IP3) Supply Current (Idd)(Vdd = +3V) 10 14 Min. Typ. 7 - 14 17 0.02 1.8 15 14 13 14.5 25 51 75 0.03 2.2 Max. Units GHz dB dB/ °C dB dB dB dBm dBm dBm mA 8 - 172 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Broadband Gain & Return Loss 25 20 15 RESPONSE (dB) 10 Gain vs. Temperature 25 8 LOW NOISE AMPLIFIERS - SMT 8 - 173 20 GAIN (dB) 5 0 -5 -10 -15 -20 -25 0 4 8 S21 S11 S22 15 10 +25C +85C -40C 5 0 12 16 20 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) FREQUENCY (GHz) Input Return Loss vs. Temperature 0 +25C +85C -40C Output Return Loss vs. Temperature 0 +25C +85C -40C -5 RETURN LOSS (dB) -5 RETURN LOSS (dB) 12 13 14 15 -10 -10 -15 -15 -20 -20 -25 6 7 8 9 10 11 FREQUENCY (GHz) -25 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) Noise Figure vs. Temperature 6 5 NOISE FIGURE (dB) 4 3 2 1 0 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) Output IP3 vs. Temperature 35 30 25 20 15 10 5 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) +25C +85C -40C +25C +85C -40C F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com OIP3 (dBm) HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz 8 LOW NOISE AMPLIFIERS - SMT P1dB vs. Temperature 20 Psat vs. Temperature 20 16 P1dB (dBm) Psat (dBm) 16 12 12 +25C +85C -40C 8 +25C +85C -40C 8 4 4 0 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) 0 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) Reverse Isolation vs. Temperature 0 Power Compression @ 8 GHz 20 Pout (dBm), GAIN (dB), PAE(%) -10 ISOLATION (dB) +25C +85C -40C 15 -20 10 -30 5 -40 Pout Gain PAE -50 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) 0 -15 -10 -5 0 INPUT POWER (dBm) Gain, Power & Noise Figure vs. Supply Voltage @ 8 GHz 20 18 GAIN (dB), P1dB (dBm) 16 14 12 10 8 Noise Figure 6 4 2 0 2.5 3 Vdd (Vdc) P1dB Gain 10 9 8 7 6 5 4 3 2 1 0 3.5 NOISE FIGURE (dB) 8 - 174 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Typical Supply Current vs. Vdd Vdd (Vdc) 2.5 3.0 Idd (mA) 49 51 53 Absolute Maximum Ratings Drain Bias Voltage (Vdd1, Vdd2) RF Input Power (RFIN) (Vdd = +3.0 Vdc) Channel Temperature Continuous Pdiss (T= 85 °C) (derate 12.9 mW/°C above 85 °C) Thermal Resistance (channel to ground paddle) Storage Temperature Operating Temperature ESD Sensitivity (HBM) +3.5 Vdc +5 dBm 175 °C 1.16 W 77.5 °C/W -65 to +150 °C -40 to +85 °C Class 1A 8 LOW NOISE AMPLIFIERS - SMT 8 - 175 3.5 Note: Amplifi er will operate over full voltage ranges shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA. 2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER NICKEL. 3. DIMENSIONS ARE IN INCHES (MILLIMETERS). 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05MM DATUM – C – 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz 8 LOW NOISE AMPLIFIERS - SMT Pin Descriptions Pin Number 1, 5-8, 9 -14, 18, 20, 21, 22, 24 2, 4, 15, 17 Function N/C Description No connection required. These pins may be connected to RF/DC ground without affecting performance. Package bottom has an exposed metal paddle that must also be connected to RF/DC ground. Interface Schematic GND 3 RFIN This pin is AC coupled and matched to 50 Ohms. 16 RFOUT This pin is AC coupled and matched to 50 Ohms. 23, 19 Vdd1, Vdd2 Power Supply Voltage for the amplifier. External bypass capacitors of 100 pF, 1000pF, and 2.2 μF are required. Application Circuit Component C1, C2 C5, C6 Value 100 pF 2.2 μF 8 - 176 F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC564LC4 v02.1208 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Evaluation PCB 8 LOW NOISE AMPLIFIERS - SMT List of Material for Evaluation PCB 116156 [1] Item J1, J2 J3 - J7 C1 - C2 C3 - C4 U1 PCB [2] Description 2.92 mm PC mount SMA DC Pin 100 pF capacitor, 0402 pkg. 2.2μF Capacitor, Tantalum HMC564LC4 Amplifier 108535 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350. The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 8 - 177