HMC575LP4

HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Typical Applications Features High Output Power: +17 dBm Low Input Power Drive: -2 to +6 dBm Fo, 3Fo Isolation: 15 dBc 100 KHz SSB Phase Noise: -140 dBc/Hz Single Supply: +5V@ 90 mA RoHS Compliant 4x4 mm SMT Package 7 FREQ. MULTIPLIERS - ACTIVE - SMT The HMC575LP4 / HMC575LP4E is suitable for: • Wireless Local Loop • Point-to-Point & VSAT Radios • Test Instrumentation • Military & Space Functional Diagram General Description The HMC575LP4 & HMC575LP4E are x2 active broadband frequency multipliers utilizing GaAs PHEMT technology in a leadless RoHS compliant SMT package. When driven by a 3 dBm signal, the multiplier provides +17 dBm typical output power from 6 to 9 GHz. The Fo and 3Fo isolations are 15 dBc with respect to output signal level. This frequency multiplier features DC blocked I/O’s, and is ideal for use in LO multiplier chains for Pt to Pt & VSAT Radios yielding reduced parts count vs. traditional approaches. The low additive SSB Phase Noise of -140 dBc/Hz at 100 kHz offset helps maintain good system noise performance. The HMC575LP4 & HMC575LP4E are compatible with surface mount manufacturing techniques. Electrical Specifi cations, TA = +25° C, Vdd1, Vdd2 = +5V, 3 dBm Drive Level Parameter Frequency Range, Input Frequency Range, Output Output Power Fo Isolation (with respect to output level) 3Fo Isolation (with respect to output level) Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Idd1 & Idd2) 14 Min. Typ. 3 - 4.5 6-9 17 15 15 15 12 -140 90 Max. Units GHz GHz dBm dBc dBc dB dB dBc/Hz mA 7 - 94 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Output Power vs. Temperature @ 3 dBm Drive Level 25 Output Power vs. Drive Level 25 20 7 -2dBm 0dBm 2dBm 4dBm 6dBm OUTPUT POWER (dBm) OUTPUT POWER (dBm) 20 15 10 5 0 -5 15 +25C +85C -40C 10 5 0 5.5 -10 6 6.5 7 7.5 8 8.5 9 9.5 6 6.5 7 7.5 8 8.5 9 OUTPUT FREQUENCY (GHz) FREQUENCY (GHz) Output Power vs. Supply Voltage @ 3 dBm Drive Level 25 Isolation @ 3 dBm Drive Level 25 20 OUTPUT POWER (dBm) OUTPUT POWER (dBm) 20 15 10 5 0 -5 -10 Fo 2Fo 3Fo 15 Vdd=4.5V Vdd=5.0V Vdd=5.5V 10 5 0 6 6.5 7 7.5 8 8.5 9 OUTPUT FREQUENCY (GHz) -15 6 6.5 7 7.5 8 8.5 9 OUTPUT FREQUENCY (GHz) Output Power vs. Input Power 25 20 OUTPUT POWER (dBm) 15 10 5 0 -5 -10 -15 -10 6 GHz 7.5GHz 9 GHz -8 -6 -4 -2 0 2 4 6 8 10 INPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 95 FREQ. MULTIPLIERS - ACTIVE - SMT HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Input Return Loss vs. Temperature Output Return Loss vs. Temperature 0 -2 OUTPUT RETURN LOSS (dB) INPUT RETURN LOSS (dB) 7 FREQ. MULTIPLIERS - ACTIVE - SMT 0 -5 +25C +85C -40C -4 -6 -8 -10 -12 -14 -16 -18 +25C +85C -40C -10 -15 -20 -25 3 3.25 3.5 3.75 4 4.25 4.5 FREQUENCY (GHz) -20 6 6.5 7 7.5 8 8.5 9 FREQUENCY (GHz) Absolute Maximum Ratings RF Input (Vdd = +5V) Supply Voltage (Vdd) Channel Temperature Continuous Pdiss (T= 85 °C) (derate 7.9 mW/°C above 85 °C) Thermal Resistance (channel to ground paddle) Storage Temperature Operating Temperature +13 dBm +6.0 Vdc 150 °C 512 mW 127 °C/W -65 to +150 °C -40 to +85 °C Typical Supply Current vs. Vdd Vdd (Vdc) 4.5 5.0 5.5 Idd (mA) 89 90 91 Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 7 - 96 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Outline Drawing 7 FREQ. MULTIPLIERS - ACTIVE - SMT 7 - 97 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC575LP4 HMC575LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H575 XXXX H575 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Pin Description 7 FREQ. MULTIPLIERS - ACTIVE - SMT Pin Number 1, 5 - 14, 18, 19, 21, 23, 24 Function Description These pins are internally not connected; however, this product was specified with these pins connected to RF/ DC ground. Package bottom must also be connected to RF/DC ground. Interface Schematic N/C 2, 4, 15, 17 GND 3 RFIN Pin is AC coupled and matched to 50 Ohms from 3 - 4.5 GHz. 16 RFOUT Pin is AC coupled and matched to 50 Ohms from 6 - 9 GHz. 20, 22 Vdd2, Vdd1 Supply voltage 5V ± 0.5V. External bypass capacitors of 100 pF and 2.2 μF are required. Application Circuit Component C1, C2 C3, C4 Value 100 pF 2.2 μF 7 - 98 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC575LP4 / 575LP4E v00.0506 SMT GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 6 - 9 GHz OUTPUT Evaluation PCB 7 FREQ. MULTIPLIERS - ACTIVE - SMT List of Materials for Evaluation PCB 112405 [1] Item J1, J2 J3 - J5 C1, C2 C3, C4 U1 PCB [2] Description PCB Mount SRI SMA Connector DC Pin 100 pF Capacitor, 0402 Pkg. 2.2 μF Tantalum Capacitor HMC575LP4 / HMC575LP4E x2 Active Multiplier 115270 Eval Board The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 99