HMC579_09

HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Typical Applications Features High Output Power: +13 dBm Low Input Power Drive: 0 to +6 dBm Fo Isolation: >25 dBc @ Fout= 38 GHz 100 KHz SSB Phase Noise: -127 dBc/Hz Single Supply: +5V@ 70 mA Die Size: 1.18 mm x 1.23 mm x 0.1 mm 2 FREQUENCY MULTIPLIERS - ACTIVE - CHIP The HMC579 is suitable for: • Clock Generation Applications: SONET OC-192 & SDH STM-64 • Point-to-Point & VSAT Radios • Test Instrumentation • Military EW / Radar • Space Functional Diagram General Description The HMC579 die is a x2 active broadband frequency multiplier utilizing GaAs PHEMT technology. When driven by a +3 dBm signal, the multiplier provides +13 dBm typical output power from 32 to 46 GHz. The Fo isolation is >25 dBc at 38 GHz. The HMC579 is ideal for use in LO multiplier chains for Pt to Pt & VSAT Radios yielding reduced parts count vs. traditional approaches. The low additive SSB Phase Noise of -127 dBc/Hz at 100 kHz offset helps maintain good system noise performance. Electrical Specifi cations, TA = +25° C, Vdd1, Vdd2 = 5.0V, 3 dBm Drive Level Parameter Frequency Range, Input Frequency Range, Output Output Power Fo Isolation (with respect to output level) Input Return Loss Output Return Loss SSB Phase Noise (100 kHz Offset) Supply Current (Idd1, Idd2) 8 Min. Typ. 16 - 23 32 - 46 13 25 12 8 -127 70 Max. Units GHz GHz dBm dBc dB dB dBc/Hz mA 2 - 56 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Output Power vs. Temperature @ 3 dBm Drive Level 20 18 OUTPUT POWER (dBm) OUTPUT POWER (dBm) 16 14 12 10 8 6 4 2 0 30 32 34 36 38 40 42 44 46 48 OUTPUT FREQUENCY (GHz) +25C +85C -55C Output Power vs. Drive Level 25 20 15 10 5 0 -5 -10 -15 -20 -25 30 32 34 36 38 40 42 44 46 48 OUTPUT FREQUENCY (GHz) -6dBm -4dBm -2dBm 0dBm 2dBm 4dBm 6dBm 2 FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 - 57 Output Power vs. Supply Voltage @ 3 dBm Drive Level 20 18 OUTPUT POWER (dBm) Isolation @ 3 dBm Drive Level 20 14 12 10 8 6 4 2 0 30 32 34 36 38 40 42 44 46 48 OUTPUT FREQUENCY (GHz) 4.5V 5.0V 5.5V OUTPUT POWER (dBm) 16 10 0 Fo 2Fo -10 -20 -30 30 32 34 36 38 40 42 44 46 48 OUTPUT FREQUENCY (GHz) Output Power vs. Input Power 20 15 OUTPUT POWER (dBm) 10 5 0 -5 -10 -15 -20 -10 32GHz 39GHz 46GHz -8 -6 -4 -2 0 2 4 6 8 10 INPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Input Return Loss vs. Temperature Output Return Loss vs. Temperature 0 OUTPUT RETURN LOSS (dB) -2 -4 -6 -8 -10 -12 -14 -16 -18 +25C +85C -55C INPUT RETURN LOSS (dB) 2 FREQUENCY MULTIPLIERS - ACTIVE - CHIP 0 +25C +85C -55C -5 -10 -15 -20 -25 15 16 17 18 19 20 21 22 23 24 FREQUENCY (GHz) -20 30 32 34 36 38 40 42 44 46 48 FREQUENCY (GHz) 2 - 58 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Absolute Maximum Ratings RF Input (Vdd = +5V) Supply Voltage (Vdd1, Vdd2) Channel Temperature Continuous Pdiss (T= 85 °C) (derate 7.3 mW/°C above 85 °C) Thermal Resistance (Channel to die bottom) Storage Temperature Operating Temperature +13 dBm +6.0 Vdc 175 °C 656 mW 137 °C/W -65 to +150 °C -55 to +85 °C Typical Supply Current vs. Vdd Vdd (V) 4.5 5.0 5.5 Idd (mA) 69 70 2 FREQUENCY MULTIPLIERS - ACTIVE - CHIP 2 - 59 70 Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Die Packaging Information [1] Standard GP-2 (Gel Pack) Alternate [2] — [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] Reference this suffix only when ordering alternate die packaging. NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. 2. DIE THICKNESS IS .004” 3. TYPICAL BOND PAD IS .004” SQUARE. 4. BOND PAD METALIZATION: GOLD 5. BACKSIDE METALIZATION: GOLD 6. BACKSIDE METAL IS GROUND. 7. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS. 8. OVERALL DIE SIZE ± 0.002” For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Pad Description 2 FREQUENCY MULTIPLIERS - ACTIVE - CHIP Pad Number Function Description Interface Schematic 1, 2 Vdd1, Vdd2 Supply voltage 5V ± 0.5V. 3 RFOUT Pin is AC coupled and matched to 50 Ohms from 32 - 46 GHz. 4, 5 GND Die bottom must be connected to RF ground. 6 RFIN Pin is AC coupled and matched to 50 Ohms from 16 - 23 GHz. Assembly Diagram 2 - 60 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC579 v01.0608 GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT Mounting & Bonding Techniques for Millimeterwave GaAs MMICs The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). Microstrip substrates should be brought as close to the die as possible in order to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length