HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
Features
Triple Output: Fo = 11.1 - 12.4 GHz Fo/2 = 5.55 - 6.2 GHz Fo/4 = 2.78 - 3.1 GHz Pout: +9 dBm Phase Noise: -110 dBc/Hz @100 kHz Typ. No External Resonator Needed 32 Lead 5x5mm SMT Package: 25mm²
Typical Applications
Low noise MMIC VCO w/Half Frequency, Divide-by-4 Outputs for: • Point to Point/Multipoint Radio • Test Equipment & Industrial Controls • SATCOM • Military End-Use
Functional Diagram
General Description
The HMC582LP5 & HMC582LP5E are GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs. The HMC582LP5 & HMC582LP5E integrate resonators, negative resistance devices, varactor diodes and feature half frequency and divide-by-4 outputs. The VCO’s phase noise performance is excellent over temperature, shock, and process due to the oscillator’s monolithic structure. Power output is +9 dBm typical from a +5V supply voltage. The prescaler and RF/2 functions can be disabled to conserve current if not required. The voltage controlled oscillator is packaged in a leadless QFN 5x5 mm surface mount package, and requires no external matching components.
8
VCOS with Fo/2 OUTPUT - SMT
Electrical Specifications, TA = +25° C, Vcc (Dig), Vcc (Amp), Vcc (RF) = +5V
Parameter Frequency Range Fo Fo/2 RFOUT RFOUT/2 RFOUT/4 +5 +8 -9 -110 Vtune Icc(Dig) + Icc(Amp) + Icc(RF) 2 290 350 12 390 10 2 1/2 2nd 3rd 32 25 30 5 30 1.2 Min. Typ. 11.1 - 12.4 5.55 - 6.2 +12 +14 -3 Max. Units GHz GHz dBm dBm dBm dBc/Hz V mA µA dB dBc dBc dBc MHz pp MHz/V MHz/°C
Power Output SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RFOUT Tune Voltage Supply Current Tune Port Leakage Current (Vtune= 13V) Output Return Loss Harmonics/Subharmonics
Pulling (into a 2.0:1 VSWR) Pushing @ Vtune= 5V Frequency Drift Rate
8-1
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
Frequency vs. Tuning Voltage, T= 25°C
13.8 OUTPUT FREQUENCY (GHz)
Frequency vs. Tuning Voltage, Vcc = +5V
13.6 OUTPUT FREQUENCY (GHz)
12.8
13
12
+25C +85C -40C
12.2
11.2
11.4
Vcc= 4.75V Vcc= 5.00V Vcc= 5.25V
10.4
10.6
9.6 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (Volts)
9.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (Volts)
Sensitivity vs. Tuning Voltage, Vcc = +5V
700 600
Output Power vs. Tuning Voltage, Vcc = +5V
16 14 OUTPUT POWER (dBm)
SENSITIVITY (MHz/Volt)
500 400 300 200 100 0 0 1 2 3 4 5 6 7
+25C +85C -40C
12 10
8
+25C +85C -40C
6 4 2 0
8
9
10
11 12
13
0
1
2
3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (Volts)
TUNING VOLTAGE (Volts)
SSB Phase Noise vs. Tuning Voltage
-75 SSB PHASE NOISE (dBc/Hz)
SSB Phase Noise @ Vtune = +5V
0 SSB PHASE NOISE (dBc/Hz) -30 -60 -90 -120 -150 -180 2 10
+25C +85C -40C
-85
-95
10khz 100khz
-105
-115
-125 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (VOLTS)
10
3
10
4
10
5
10
6
10
7
TUNING VOLTAGE (VOLTS)
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
8-2
VCOS with Fo/2 OUTPUT - SMT
8
HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
RFOUT/2 Output Power vs. Tuning Voltage, Vcc = +5V
16 14 OUTPUT POWER (dBm) 12 10 8 6 4 2 0
+25C +85C -40C
RFOUT/2 Frequency vs. Tuning Voltage, Vcc = +5V
6.6 OUTPUT FREQUENCY (GHz) 6.4 6.2 6 5.8 5.6 5.4 5.2 5 4.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOTLAGE (Volts)
+25C +85C -40C
0
1
2
3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (Volts)
Divide-by-4 Frequency vs. Tuning Voltage, Vcc = +5V
3.3 OUTPUT FREQUENCY (GHz)
Divide-by-4 Output Power vs. Tuning Voltage, Vcc = +5V
0 -1 OUTPUT POWER (dBm) -2 -3 -4 -5 -6 -7 -8 -9 -10
+25C +85C -40C
8
VCOS with Fo/2 OUTPUT - SMT
3.2 3.1 3 2.9 2.8 2.7 2.6 2.5 2.4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (Volts)
+25C +85C -40C
0
1
2
3
4
5
6
7
8
9
10
11 12
13
TUNING VOLTAGE (Volts)
Absolute Maximum Ratings
Vcc(Dig), Vcc(Amp), Vcc(RF) Vtune Junction Temperature Continuous Pdiss (T=85 °C) (derate 43.5 mW/C above 85 °C Thermal Resistance (junction to ground paddle) Storage Temperature Operating Temperature ESD Sensitivity (HBM) +5.5 Vdc 0 to +15V 135 °C 2.17 W 23 °C/W -65 to +150 °C -40 to +85 °C Class 1A
Typical Supply Current vs. Vcc
Vcc (V) 4.75 5.00 5.25 Icc (mA) 320 350 380
Note: VCO will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS
8-3
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
Outline Drawing
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
8
Package Marking [3] H582 XXXX H582 XXXX
Package Information
Part Number HMC582LP5 HMC582LP5E Package Body Material Low Stress Injection Molded Plastic
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Lead Finish Sn/Pb Solder 100% matte Sn
MSL Rating MSL3 MSL3
[1]
RoHS-compliant Low Stress Injection Molded Plastic
[2]
[1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX
Pin Descriptions
Pin Number 1 - 3, 8 - 10, 13 - 18, 20, 22 - 28, 30 - 32 Function N/C Description No Connection. These pins may be connected to RF/ DC ground. Performance will not be affected. Interface Schematic
4
RFOUT/4
Divide-by-4 output. DC block required.
6
Vcc (Dig)
Supply voltage for prescaler. If prescaler is not required, this pin may be left open to conserve approximately 65 mA of current.
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
8-4
VCOS with Fo/2 OUTPUT - SMT
HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
Pin Descriptions
Pin Number Function Description Interface Schematic
7
Vcc (Amp)
Supply voltage for RFOUT/2 output. If RFOUT/2 is not required, this pin may be left open to conserve approximately 30 mA of current.
12
RFOUT/2
Half frequency output (AC coupled).
19
RF OUT
RF output (AC coupled).
8
VCOS with Fo/2 OUTPUT - SMT
21
Vcc (RF)
Supply Voltage, +5V
29
VTUNE
Control voltage and modulation input. Modulation bandwidth dependent on drive source impedance. See “Determining the FM Bandwidth of a Wideband Varactor Tuned VCO” application note. Package bottom has an exposed metal paddle that must be connected to RF/DC ground.
5, 11, Paddle
GND
Typical Application Circuit
8-5
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC582LP5 / 582LP5E
v03.0811
MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 11.1 - 12.4 GHz
Evaluation PCB
8
VCOS with Fo/2 OUTPUT - SMT
8-6
List of Materials for Evaluation PCB 110227 [1]
Item J1 - J4 J5 - J6 C1 - C3 C4 C5 - C7 U1 PCB [2] Description PCB Mount SMA RF Connector 2 mm DC Header 100 pF Capacitor, 0402 Pkg. 1,000 pF Capacitor, 0402 Pkg. 2.2 µF Tantalum Capacitor HMC582LP5 / HMC582LP5E VCO 110225 Eval Board
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com
