HMC596LP4_09

HMC596LP4 / HMC596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Typical Applications 4x2 Switch Matrix for 0.2 - 3.0 GHz Applications: • DBS LNBs & Multiswitches • Cable Modem / CATV • Cellular Systems Features High Isolation / Low Insertion Loss Integrated CMOS Compatible 4 Bit Decoder Single Positive Supply: Vdd = +5V 24 Lead 4x4mm QFN Package: 9 mm2 4x4 Switch Matrix Using Two ICs Functional Diagram General Description The HMC596LP4 & HMC596LP4E are low-cost 4x2 switch matrices in leadless QFN 4x4 mm surface mount packages for use in Satellite / DBS, LNBs and multiswitches from 200 to 3000 MHz. A positive voltage controlled 4 bit decoder is integrated on the switch. The switches may be used in either 75 ohm or 50 ohm systems. 12 SWITCHES - MATRIX - SMT Both switch outputs (OP1 & OP2) can independently select any of the four inputs (HH, HL, VH, VL) or simultaneously select the same inputs. Note that the switch is bi-directional and input/output functionality may be interchanged. All data presented was measured in a 50 ohm (input/output) system. Electrical Specifi cations, TA = +25° C, Vdd= +5V, 50 Ohm System Parameter Insertion Loss Conditions Frequency 200 - 950 950 - 2150 2150 - 3000 200 - 950 950 - 1450 1450 - 2150 2150 - 3000 Input Selected 200 - 950 950 - 2150 2150 - 3000 200 - 950 950 - 2150 2150 - 3000 Min. Typ. 6 6.5 7.5 50 45 43 40 30 15 12 17 22 18 Max. 7 8 9 Units dB dB dB dB dB dB dB dB dB dB dB dB dB Isolation 42 37 Return Loss (VL, HL, VH, HH) 25 10 7 Return Loss (VL, HL, VH, HH) Input Deselected 12 - 114 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Electrical Specifi cations, TA = +25° C, Vdd= +5V, 50 Ohm System (Continued) Parameter Return Loss (Output OP1/OP2) Output IP3 Input Power for 1 dB Compression Switching Speed tRISE / tFALL (10/90% RF) tON / tOFF (50% CTL to 10/90% RF) 6.0 6.5 ns ns Conditions Frequency 200 - 950 950 - 2150 2150 - 3000 200 - 3000 200 - 3000 Min. 9 11 8 22 18 Typ. 13 14 13 27 22 Max. Units dB dB dB dBm dBm OP1 Isolation 950 - 1450 MHz Input to Output State HL to OP1 VL to OP1 VH to OP1 HH to OP1 Interfering Signal VL to OP1 All Other States VH to OP1 All Other States All States All States State 11 All Other States 2 All Other States All States All States Min. (dB) 38 40 39 40 43 37 Typ. (dB) 41 >43 42 >43 >46 >40 OP2 Isolation 950 - 1450 MHz Input to Output State HL to OP2 VH to OP2 VL to OP2 HH to OP2 Interfering Signal HH to OP2 All Other States HL to OP2 All Other States HL to OP2 All Other States All States State 15 All Other States 6 All Other States 1 All Other States All States Min. (dB) 38 40 37 40 37 40 38 Typ. (dB) 41 >43 40 >43 40 >43 >41 12 SWITCHES - MATRIX - SMT 12 - 115 Insertion Loss on OP1 0 VL to OP1 (state 1) VL to OP1 (state 2) VH to OP1 (state 5) VH to OP1 (state 6) HL to OP1 (state 11) HL to OP1 (state 12) HH to OP1 (state 15) HH to OP1 (state 16) Insertion Loss on OP2 0 VL to OP2 (state 1) VL to OP2 (state 5) VH to OP2 (state 2) VH to OP2 (state 6) HL to OP2 (state 11) HL to OP2 (state 15) HH to OP2 (state 12) HH to OP2 (state 16) INSERTION LOSS (dB) -4 INSERTION LOSS (dB) 2.6 3 -2 -2 -4 -6 -6 -8 -8 -10 0.2 0.6 1 1.4 1.8 2.2 -10 0.2 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Return Loss 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 0.2 Input RL, Input Selected Input RL, Input Deselected Output RL Typical Insertion Loss vs. Temperature 0 +25C +85C -40C INSERTION LOSS (dB) -2 -4 -6 -8 0.6 1 1.4 1.8 2.2 2.6 3 -10 0.2 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) Isolation When HL is Connected to OP1* 0 Isolation When VH is Connected to OP1* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 HH to OP1 (state 8) HL to OP1 (state 6) HL to OP1 (state 7) VL to OP1 (state 6) VL to OP1 (state 5) HH to OP1 (state 6) ISOLATION (dB) 12 SWITCHES - MATRIX - SMT -10 -20 -30 -40 -50 -60 0.2 HH to OP1 (state 11) HH to OP1 (state 12) VH to OP1 (state 10) VL to OP1 (state 11) VL to OP1 (state 9) VH to OP1 (state 11) 0.6 1 1.4 1.8 2.2 2.6 3 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) Isolation When VL is Connected to OP1* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 HL to OP1 (state 3) VH to OP1 (state 2) HH to OP1 (state 1) HH to OP1 (state 4) VH to OP1 (state 1) HL to OP1 (state 1) Isolation When HH is Connected to OP1* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 VL to OP1 (state 16) VH to OP1 (state 16) VL to OP1 (state 13) VH to OP1 (state 14) HL to OP1 (state 16) HL to OP1 (state 15) 0.6 1 1.4 1.8 2.2 2.6 3 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) * Isolation is recorded above insertion loss & measured at output of switch. 12 - 116 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Isolation When HL is Connected to OP2* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 HH to OP2 (state 11) HH to OP2 (state 15) VH to OP2 (state 7) VH to OP2 (state 11) VL to OP2 (state 11) VL to OP2 (state 3) Isolation When VL is Connected to OP2* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 VH to OP2 (state 1) VH to OP2 (state 5) HH to OP2 (state 1) HH to OP2 (state 13) HL to OP2 (state 1) HL to OP2 (state 9) 0.6 1 1.4 1.8 2.2 2.6 3 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) Isolation When VH is Connected to OP2* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 HH to OP2 (state 14) HL to OP2 (state 6) VL to OP2 (state 2) VL to OP2 (state 6) HH to OP2 (state 6) HL to OP2 (state 10) Isolation When HH is Connected to OP2* 0 -10 ISOLATION (dB) -20 -30 -40 -50 -60 0.2 HL to OP2 (state 12) HL to OP2 (state 16) VH to OP2 (state 8) VH to OP2 (state 16) VL to OP2 (state 16) VL to OP2 (state 4) 12 SWITCHES - MATRIX - SMT 12 - 117 0.6 1 1.4 1.8 2.2 2.6 3 0.6 1 1.4 1.8 2.2 2.6 3 FREQUENCY (GHz) FREQUENCY (GHz) Output Third Order Intercept Point Path VL to OP1 VL to OP2 HL to OP1 HL to OP2 VH to OP1 VH to OP2 HH to OP1 HH to OP2 State 1 1 11 11 6 6 16 16 F1 & F2 Pout (dBm) -12 -12 -12 -12 -12 -12 -12 -12 Intermod Pout (dBm) -91 -91 -92 -91 -90 -90 -91 -91 Intermodulation Ratio (dBc) 79 79 80 79 78 78 79 79 Output IP3 (dBm) 27.5 27.5 28 27.5 27 27 27.5 27.5 Test Conditions Temperature = +25° C F1 = 2150 (MHz): -12 dBm at the Output F2 = 2151 (MHz): -12 dBm at the Output Vdd = +5V VCTL Low = 0V, High = +5V * Isolation is recorded above insertion loss & measured at output of switch. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Truth Table Control Input State 1 2 3 4 5 6 7 8 9 10 11 12 13 HV 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Tone 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 HV 2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Tone 2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Output to Input State OP1 VL VL VL VL VH VH VH VH HL HL HL HL HH HH HH HH OP2 VL VH HL HH VL VH HL HH VL VH HL HH VL VH HL HH VL to OP1 LOSS LOSS LOSS LOSS ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL HL to OP1 ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL LOSS LOSS LOSS LOSS ISOL ISOL ISOL ISOL VH to OP1 ISOL ISOL ISOL ISOL LOSS LOSS LOSS LOSS ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL RF Path State HH to OP1 ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL ISOL LOSS LOSS LOSS LOSS VL to OP2 LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL HL to OP2 ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL VH to OP2 ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL HH to OP2 ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS ISOL ISOL ISOL LOSS 12 SWITCHES - MATRIX - SMT 14 15 16 Control Voltages HV1, Tone1, HV2, Tone2 State Low (0) High (1) Bias Condition 0 to 0.8 Vdc @ 0.5 μA Typical +2.0 to +5.0 Vdc @ 0.5 μA Typical Bias Voltage Vdd Range = +5.0 Vdc ± 10 % Vdd (Vdc) +5.0 Idd (Typ.) (mA) 0.2 Idd (Max.) (mA) 0.4 DC Blocking And Decoupling Capacitors The HMC596LP4(E) requires DC blocks on all 6 RF ports (OP1, OP2, VL, HL, VH, HH). Characterization on the HMC596LP4(E) was done using 0402 size 330pF capacitors on all RF ports. A 1,000 pF DC decoupling capacitor (0603 size) is recommended for the Vdd pin. 12 - 118 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Absolute Maximum Ratings Bias Voltage Range (Vdd) Control Voltage Range (All Logic Lines) Channel Temperature Thermal Resistance Storage Temperature Operating Temperature Maximum Input Power (Each Input) +8.0 Vdc Vdd +0.5 to -0.2V Vdc 150 °C 325 °C/W -65 to +150 °C -40 to +85 °C +23 dBm (200 - 2150 MHz) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing 12 SWITCHES - MATRIX - SMT 12 - 119 NOTES: 1. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.05mm MAX. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL NC LEADS, GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number HMC596LP4 HMC596LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H596 XXXX H596 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Pin Descriptions Pin Number 1, 2, 4 - 6, 13 - 15, 17, 18 Function GND Description Package bottom has exposed metal paddle that must be connected to PCB RF ground. Switch RF Input. This pin is DC coupled and should be DC blocked externally using a series capacitor. Select value based on lowest frequency of operation. Switch RF Input. This pin is DC coupled and should be DC blocked externally using a series capacitor. Select value based on lowest frequency of operation. Interface Schematic 3, 16, 19, 24 HL, VL, VH, HH 7, 12 OP1, OP2 8 9 10 11 HV2 TONE2 Control Inputs. See truth and control voltage table. TONE1 HV1 20, 22, 23 N/C Not connected. 12 SWITCHES - MATRIX - SMT 21 Vdd Supply Voltage Switch Application Circuit for 4x4 Switch Matrix The HMC596LP4(E) switch can operate as a 4x4 switch by connecting the 4 inputs of two switches directly together. The VL, VH, HL, and HH inputs of the first switch should be connected to the second switch, as illustrated. Mirror image switch performance can be realized by inverting the HV1 & HV2 logic control signals of one of the HMC596LP4(E) switches. The input loading impedance of two switches in parallel should be 31.25 ohms. The output loading impedance on each output should be 75 ohms. The interconnect RF line between the switch’s inputs should be an RF trace with a characteristic impedance of 62.5 ohms. This will allow the switch to remain matched in all possible switch states. The HMC596LP4(E) does not provide output to output (OP1 to OP2) isolation. For this reason, it is recommended that external amplifiers should be used at each output. The amplifier’s reverse isolation will provide output to output isolation, if this is necessary. Each HMC596LP4(E) requires DC blocking capacitors on ALL RF input and output ports. 12 - 120 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC596LP4 / 596LP4E v01.0409 SMT CMOS 4x2 SWITCH MATRIX, 0.2 - 3.0 GHz Evaluation PCB 12 SWITCHES - MATRIX - SMT 12 - 121 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown above. A generous number of ground vias should be used to interconnect top/bottom ground planes. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. List of Materials for Evaluation PCB 104130 [1] Item J2 - J9 J1 C1 - C8 C9 U1 PCB [2] Description PCB Mount SMA RF Connector DC Connector 330 pF Capacitor, 0402 Pkg. 1,000 pF Capacitor, 0603 Pkg. HMC596LP4 / HMC596LP4E 4x2 Switch Matrix 104113 Eval Board Multi Pin DC Interface (J1) Pin 1 2 3 4 5 6 7 8 9 Line Vdd Tone 1 GND Tone 2 GND HV1 N/C N/C HV2 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com