HMC607G7_08

HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Typical Applications The HMC607G7 is ideal for: • Telecom Infrastructure • Microwave Radio & VSAT • Military Radios, Radar & ECM • Space Systems • Test Instrumentation Features High Isolation: 55 dB @ 2 GHz 42 dB @ 6 GHz Low Insertion Loss: 1.9 dB Typical @ 6 GHz Non-Reflective Design Hermetic Surface Mount Package Higher Performance Drop-In Replacement for: Skyworks AS406M2-10 Functional Diagram 10 SWITCHES - SMT General Description The HMC607G7 is a broadband high isolation non-reflective GaAs MESFET SPDT switch in a hermetic surface mount package. Covering DC to 6 GHz, the switch features >55 dB isolation up to 2 GHz and >42 dB isolation up to 6 GHz. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter Insertion Loss Frequency DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz “On State” DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz 0.5 - 6.0 GHz 0.5 - 6.0 GHz 23 50 41 37 Min. Typ. 1.3 1.4 1.9 55 46 42 20 17 13 13 13 13 27 47 Max. 1.6 1.7 2.3 Units dB dB dB dB dB dB dB dB dB dB dB dB dBm dBm Isolation Return Loss Return Loss RF1, RF2 “Off State” Input Power for 1 dB Compression Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone, 1 MHz Tone Separation) Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 6.0 GHz 3 6 ns ns 10 - 372 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Insertion Loss 0 Isolation 0 INSERTION LOSS (dB) -1 -20 -2 ISOLATION (dB) RF1 RF2 -40 -3 +25 C +85 C -40 C -60 -4 -5 0 1 2 3 4 5 6 7 FREQUENCY (GHz) -80 0 1 2 3 4 5 6 7 FREQUENCY (GHz) 10 SWITCHES - SMT 10 - 373 Return Loss 0 RFC RF1, RF2 on RF1, RF2 off 0.1 and 1 dB Input Compression Point 35 COMPRESSION POINT (dBm) 1 dB Compression Point 0.1 dB Compression Point -5 RETURN LOSS (dB) 30 -10 25 -15 20 -20 -25 0 1 2 3 4 5 6 7 FREQUENCY (GHz) 15 0 1 2 3 4 5 FREQUENCY (GHz) 6 7 Input Third Order Intercept Point 60 55 50 IP3 (dBm) 45 40 35 30 0 1 2 3 4 5 FREQUENCY (GHz) 6 7 +25 C +85 C -40 C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Absolute Maximum Ratings RF Input Power (A, A, B, B = 0/-5V) (0.5 - 6 GHz) Control Voltage Range (A, A, B, B) Channel Temperature Thermal Resistance (RTH) (junction to lead) Storage Temperature Operating Temperature +30 dBm (@ +50 °C) +1.0V to -7.5 Vdc 150 °C 94 °C/W -65 to +150 °C -40 to +85 °C Control Voltages State Low High Bias Condition 0 to -0.2V @ 10 uA Max. -5V @ 10 uA Typ. to -7V @ 45 uA Typ. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Truth Table Control Input Signal Path State A Low High Low High A High Low High Low RFC to RF1 ON OFF OFF ON RFC to RF2 OFF ON OFF ON 10 SWITCHES - SMT B Low High High Low B High Low Low High Caution: Do not “Hot Switch” power levels greater than +27 dBm (A, A, B, B = 0/-5V). Suggested Driver Circuit for Single Line Control 10 - 374 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Outline Drawing 10 SWITCHES - SMT Interface Schematic NOTES: 1. PACKAGE BODY MATERIAL: WHITE ALUMINA 92% 2. CONDUCTOR TRACES MATERIAL: THICK FILM TUNGSTEN. 3. LEAD, BASE, COVER MATERIAL: KOVAR™. 4. PLATING: ELECTROLYTIC GOLD 50 MICROINCHES MIN, OVER ELECTROLYTIC NICKEL 50 MICROINCHES MIN. 5. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. 6. TOLERANCES: .±005 [0.13] UNLESS OTHERWISE SPECIFIED. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Pin Descriptions Pin Number 1, 2, 3 Function RF2, RFC, RF1 Description This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. 4 5 6 7 B B See truth table and control voltage table. A A GND Package bottom must also be connected to PCB RF ground. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 375 HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Evaluation PCB 10 SWITCHES - SMT List of Materials for Evaluation PBC 116577 [1] Item J1 - J3 J4 - J8 R1 - R4 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 100 Ohm Resistor, 0402 Pkg. HMC607G7 SPDT Switch 116575 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. 10 - 376 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Notes: 10 SWITCHES - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 377