HMC630LP3

HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Typical Applications The HMC630LP3(E) is ideal for: • Wireless Infrastructure HPA & MCPA Error Correction • Pre-Distortion or Feed-Forward Linearization • Cellular / 3G Systems • Beam Forming or RF Cancellation Circuits 16 Lead 3x3mm SMT Package: 9mm2 Features Continuous Phase Control: 360° Continuous Gain Control: 40 dB Low Output Noise Floor: -162 dBm/Hz High Input IP3: +34 dBm 10 MODULATORS - SMT Functional Diagram General Description The HMC630LP3 & HMC630LP3E are high dynamic range Vector Modulator RFICs which are targeted for RF predistortion and feed-forward cancellation circuits, as well as RF beam forming and amplitude/ phase correction circuits. The I & Q ports of the HMC630LP3(E) can be used to continuously vary the phase and amplitude of RF signals by up to 360 degrees and 40 dB respectively, while supporting a 3 dB modulation bandwidth of 180 MHz. With an output IP3 of +24.5 dBm and output noise floor of -162 dBm/Hz (at maximum gain setting), the output IP3/ noise floor ratio is 186.5 dB. Electrical Specifi cations, TA = +25° C, Vcc= +8V Parameter Frequency Range Maximum Gain [1] Min. Typ. 0.7 - 1.0 Max. Units GHz dB -12 -10 0.02 0.10 40 15 17 0.03 Gain Variation Over Temperature Gain Flatness Across Any 60 MHz Bandwidth Gain Range Input Return Loss Output Return Loss Input Power for 1dB Compression (P1dB) Input Third Order Intercept (IP3) Output Noise Control Port Bandwidth (-3 dB) Control Port Impedance Control Port Capacitance Control Voltage Range Group Delay Variation Over 60 MHz Bandwidth Supply Current (Icq) 14 dB / °C dB dB dB dB dBm dBm dBm/Hz MHz Ohms pF Vdc ps mA 17 34 -162 180 1.45k 0.22 +0.5 to +2.5 20 92 Unless otherwise noted, measurements are made @ max. gain setting and 45˚ phase setting. See application circuit for details. [1] Includes loss of input balun (0.75 dB typ.). 10 - 50 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Maximum Gain vs. Temperature 0 -2 -4 -6 GAIN (dB) -8 -10 -12 -14 -16 -18 -20 0.6 0.7 0.8 0.9 1 1.1 +25C +85C -40C Maximum Gain vs. Supply Voltage 0 -2 -4 -6 GAIN (dB) -8 -10 -12 -14 -16 -18 -20 0.6 0.7 0.8 0.9 1 1.1 7.6V 8.0V 8.4V 10 MODULATORS - SMT 10 - 51 FREQUENCY (GHz) FREQUENCY (GHz) Gain vs. Phase Settings @ F= 900 MHz 0 Phase vs. Phase Settings @ F= 900 MHz vs. Various Gain Settings 360 315 -10 PHASE (DEGREES) 270 225 180 135 90 45 0 0 45 90 135 180 225 270 315 360 0 45 90 135 180 225 270 315 360 PHASE SETTING (DEGREES) PHASE SETTING (DEGREES) MAX -5dB -10dB -20dB GAIN (dB) -20 -30 -40 MAX -5dB -10dB -20dB -50 Input Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 0.6 +25C +85C -40C Output Return Loss vs. Temperature 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 0.6 +25C +85C -40C 0.7 0.8 0.9 1 1.1 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Output Noise vs. Phase Settings @ F= 900 MHz -150 -152 -154 -156 -158 -160 -162 -164 -166 -168 -170 -172 -174 -176 -178 -180 0 45 90 135 180 225 270 315 360 PHASE SETTING (DEGREES) Output Noise vs. Temperature -160 -162 NOISE (dBm/Hz) NOISE (dBm/Hz) +25C +85C -40C -164 -166 -168 10 MODULATORS - SMT -170 0.7 0.8 0.9 1 FREQUENCY (GHz) Input P1dB vs. Temperature 22 20 18 Input IP3 vs. Temperature 38 36 P1dB (dBm) IP3 (dBm) +25C +85C -40C 34 16 14 12 10 0.6 32 +25C +85C -40C 30 0.7 0.8 0.9 1 1.1 28 0.7 0.8 0.9 1 FREQUENCY (GHz) FREQUENCY (GHz) Group Delay 1300 1250 GROUP DELAY (ps) 1200 1150 1100 1050 1000 950 900 0.6 Linear Gain vs. Phase Setting 90 1 0.8 0.6 MAGNITUDE G/Gmax 0.4 0.2 0 0 30 120 60 210 330 0.7 0.8 0.9 1 1.1 240 270 300 FREQUENCY (GHz) 10 - 52 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Typical Supply Current vs. Vcc Vcc (V) 7.6 8.0 8.4 Icc (mA) 86 92 98 Absolute Maximum Ratings RF Input (Vcc = +8V) Supply Voltage (Vcc) I & Q Input Junction Temperature (Tc) Continuous Pdiss (T = 85°C) (Derate 34 mW/°C above 85°C) Thermal Resistance (Rth) (junction to ground paddle) Storage Temperature 27 dBm +10V -0.5V to +5.0V 135 °C 1.7 W 29.6 °C/W -65 to +150 °C -40 to +85 °C Note: Modulator will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Operating Temperature 10 MODULATORS - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number HMC630LP3 HMC630LP3E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] 630 XXXX 630 XXXX [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 53 HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Pin Description Pin Number 1, 4, 10 - 12 Function N/C Description No connection. These pins may be connected to RF ground. Performance will not be affected Interface Schematic 2, 3 IN, IN Differential RF inputs, 100 Ohms differential impedance. (i.e. each pin is 50 Ohms to ground). Must be DC blocked. 10 MODULATORS - SMT 5, 15 I In-phase control input. Pins 5 and 15 are redundant. Either input can be used. 6, 16 Q Quadrature control input. Pins 6 and 16 are redundant. Either input can be used. 7, 8, 13, 14 Vcc Supply Voltage, pins are DC connected on-chip. It is only necessary to supply Vcc to any 1 of the 4 pins, but all 4 pins must be bypassed to ground. (See application circuit). 9 RFOUT RF Output: Must be DC blocked. GND Ground: Backside of package has exposed metal ground paddle which must be connected to RF/DC ground. 10 - 54 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Application Circuit 10 MODULATORS - SMT 10 - 55 * Pins 15 & 16 are redundant I & Q inputs. Gain and Phase control are applied through the I and Q control ports. For a given linear gain (G) and phase (θ) setting, the voltages applied to these ports in all measurements are calculated as follows: G Cos (θ ) G max G Q (G,θ ) = Vmq + 1.0V Sin (θ ) G max I (G,θ ) = Vmi + 1.0V Where Vmi and Vmq are the I and Q voltage settings corresponding to maximum isolation at room temperature and F = 0.9 GHz. Note that G=10X and Gmax = 10Y where x = Gain Setting ( dB) and 20 y = Max Gain Setting( dB) . 20 Nominally Vmi = Vmq = 1.5V, Gmax = 0.316. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Evaluation PCB 10 MODULATORS - SMT List of Materials for Evaluation PCB 117198 [1] Item J1 - J4 J5 C1 C2, C4, C5 C3 [3] T1 L1 U1 PCB [2] Description PCB Mount SMA Connector 2 mm DC Header 4.7 μF Capacitor, Tantalum 100 pF Capacitor, 0402 Pkg. 5 pF Capacitor, 0402 pkg Balun, 0805 Pkg. ANAREN BD0810J50100A 330 nH Inductor, 0805 Pkg. HMC630LP3(E) Vector Modulator 117196 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350, Er = 3.48 [3] Locate close to HMC630LP3E package 10 - 56 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC630LP3 / 630LP3E v00.1007 GaAs HBT VECTOR MODULATOR 700 - 1000 MHz Notes: 10 MODULATORS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 57