HMC641LC4_1007

HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Features Broadband Performance: Dc - 20 Ghz high isolation: 42 dB @ 12 Ghz Low insertion Loss: 2.1 dB @ 12 Ghz integrated 2:4 ttL Decoder 24 Lead 4x4mm SMt Package: 16mm² Typical Applications the hMc641Lc4 is ideal for: • telecom infrastructure • Microwave Radio & VSAt • Military & Space hybrids • test instrumentation • SAtcOM & Sensors Functional Diagram General Description the hMc641Lc4 is a broadband non-reflective GaAs pheMt SP4t switch in a compact 4x4 mm ceramic package. covering Dc to 20 Ghz, this switch offers high isolation, low insertion loss and on-chip termination of isolated ports. this switch also includes an on board binary decoder circuit which reduces the number of required logic control lines from four to two. the hMc641Lc4 is controlled with 0/ -5V logic, exhibits fast switching speed and consumes much less Dc current than pin diode based solutions. the hMc641Lc4 is also available in die form as the hMc641. 11 SwitcheS - SPDt - SMt Electrical Specifications, TA = +25° C, With 0/-5V Control, Vss = -5V, 50 Ohm System Parameter insertion Loss isolation (RFc to RF1 - RF4) Return Loss Return Loss input Power for 1 dB compression input third Order intercept (two-tone input Power= +14 dBm each tone) Switching characteristics tRiSe, tFALL (10/90% RF) tON, tOFF (50% ctL to 10/90% RF) “On State” “Off State” Frequency Dc - 12 Ghz Dc - 20 Ghz Dc - 12 Ghz Dc - 20 Ghz Dc - 12 Ghz Dc - 20 Ghz Dc - 20 Ghz 0.05 - 0.25 Ghz 0.25- 20 Ghz 0.05 - 0.25 Ghz 0.25 - 20 Ghz Dc - 20 Ghz 10 20 30 30 Min. typ. 1.6 2.3 42 40 18 17 13 15 23 30 39 15 88 Max. 2.8 3.5 Units dB dB dB dB dB dB dB dBm dBm dBm dBm ns ns 11 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Isolation 0 -10 RF1 RF2 RF3 RF4 Insertion Loss vs. Temperature 0 INSERTION LOSS (dB) -1 -20 ISOLATION (dB) -2 -30 -40 -50 -60 -70 -3 +25 C +85 C -40 C -4 -5 0 4 8 12 16 20 24 -80 0 4 8 12 16 20 24 FREQUENCY (GHz) FREQUENCY (GHz) Return Loss 0 -5 RFC RF1,2,3,4 On RF1,2,3,4 Off 1 dB Input Compression Point 30 11 SwitcheS - SPDt - SMt 11 - 2 INPUT COMPRESSION POINT (dBm) 16 20 24 RETURN LOSS (dB) -10 -15 -20 -25 -30 -35 0 4 25 20 15 10 8 12 0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (GHz) FREQUENCY (GHz) Input Third Order Intercept Point @ 0 dBm Tone Power 50 45 40 IP3 (dBm) 35 30 25 20 15 0 5 10 15 20 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Truth Table control input A high Low high Low B high high Low Low Signal Path State RFc to: RF1 RF2 RF3 RF4 Absolute Maximum Ratings Bias Voltage (Vss) control Voltage Range (A & B) Maximum input Power channel temperature thermal Resistance channel to die bottom (insertion Loss Path) thermal Resistance channel to die bottom (terminated Path) Storage temperature Operating temperature eSD Sensitivity (hBM) -7V Vss -0.5V to +1V +24 dBm 150 °c 199 °c/w 219 °c/w -65 to +150 °c -40 to +85 °c class 1A Bias Voltage & Current Vss Range= -5.0 Vdc ±10% Vss (Vdc) -5 iss (typ) (mA) 1.7 iss (Max) (mA) 5.0 11 SwitcheS - SPDt - SMt eLectROStAtic SeNSitiVe DeVice OBSeRVe hANDLiNG PRecAUtiONS TTL/CMOS Control Voltages State Low high Bias condition -2.5V to 0V @ 30 µA typ. -5V to -3.8V @ 1.7 µA typ. 11 - 3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Outline Drawing 11 SwitcheS - SPDt - SMt 11 - 4 NOteS: 1. PAcKAGe BODY MAteRiAL: ALUMiNA 2. LeAD AND GROUND PADDLe PLAtiNG: 30-80 MicROiNcheS GOLD OVeR 50 MicROiNcheS MiNiMUM NicKeL. 3. DiMeNSiONS ARe iN iNcheS [MiLLiMeteRS]. 4. LeAD SPAciNG tOLeRANce iS NON-cUMULAtiVe 5. PAcKAGe wARP ShALL NOt eXceeD 0.05mm DAtUM -c6. ALL GROUND LeADS AND GROUND PADDLe MUSt Be SOLDeReD tO PcB RF GROUND. 7. cLASSiFieD AS MOiStURe SeNSitiVitY LeVeL (MSL) 1. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Pin Descriptions Pin Number 1, 5, 6, 13, 18 Function N/c Description these pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/Dc ground externally. these pins and the exposed ground paddle must be connected to RF/Dc ground. these pads are Dc coupled and matched to 50 Ohms. Blocking capacitors are required if RF line potential is not equal to 0V. interface Schematic 2, 4, 7, 9, 10, 12, 17, 19, 21, 22, 24 Ground Paddle 3, 8, 11, 20, 23 GND RFc, RF1, RF2, RF3, RF4 14 Vss Supply Voltage -5 Vdc ± 10%. 11 SwitcheS - SPDt - SMt 15 ctLB See truth table and control Voltage table. 16 ctLA See truth table and control Voltage table. 11 - 5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC641LC4 v00.0609 GaAs MMIC SP4T NON-REFLECTIVE SWITCH, DC - 20 GHz Evaluation PCB 11 SwitcheS - SPDt - SMt 11 - 6 List of Materials for Evaluation PCB 126511 [1] item J1 - J5 c1 U1 PcB [2] Description PcB Mount SMA connector 1000 pF capacitor, 0402 Pkg. hMc641Lc4 Switch 126508 evaluation PcB [1] Reference this number when ordering complete evaluation PcB [2] circuit Board Material: Rogers 4350 or Arlon FR4 the circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation board should be mounted to an appropriate heat sink. the evaluation circuit board shown is available from hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com