HMC807LP6CE_11

HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Features • rF Bandwidth: 12.4 gHz to 13.4 gHz • Fractional or Integer Modes • Ultra Low Phase noise 12.9 gHz; 50 MHz ref. -95 / -98 dBc/Hz @ 10 kHz (Frac / Int) -132 dBc/Hz @ 1 MHz (Open Loop) • Figure of Merit (FOM) -221 / -226 dBc/Hz (Frac / Int) • 24-bit Step Size, resolution 3 Hz typ • 225 MHz, 14-bit reference path input • direct FSK Modulation Mode • Cycle Slip Prevention • read / Write Serial Port, Chip Id • 40 Lead 6 x 6 mm SMt Package: 36 mm² Typical Applications 7 PLLS w/ Integrated VCO - SMt • VSat radio • Point-to-Point / Multi-Point radio • test equipment & Industrial Control • Military end-Use • Phased array applications Functional Diagram [1] Please refer to the pin description table for details 7-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz General Description the HMC807LP6Ce is a fully functioned Fractional-n Phase-Locked-Loop (PLL) with an Integrated Voltage Controlled Oscillator (VCO). the input reference frequency range is 100 kHz to 220 MHz while the advanced deltasigma modulator design in the fractional PLL allows both ultra-fine step sizes and very low spurious products. the highly integrated structure provides excellent phase noise performance over temperature, shock and process. the HMC807LP6Ce is packaged in a leadless QFn 6 x 6 mm surface mount package. the output power is 8 dBm typical, making the HMC807LP6Ce ideal for driving the LO port of many of Hittite’s Hi Linearity and I/Q mixer products. For theory of operation and register map refer to the “PLLs w/ Integrated VCO - Microwave VCOs” Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC807LP6CE from the “Search by Part Number” pull down menu. Electrical Specifications, TA = +25° C; VCCVCO, VDDCP, VCCCP = +5V; AVCC, VCCPS VDDPFD, AVDD, RVDD, DVDD, DVDDM, DVDDQ, VDDIO = +3.3V; AGND = DGND = 0V Parameter Condition Min. typ. Max. Units RF Output Characteristics VCO Output Frequency range VCO Output Power VCO tuning Voltage VCO tuning Sensitivity Frequency Pulling (into a 2:1 VSWr) Frequency Pushing Frequency drift rate Sub Harmonic (1/2) Harmonic (2nd) Harmonic (3rd) VCO SSB Phase noise @ 100 kHz Offset (Open Loop) Synthesizer In-Band SSB Phase noise @ 10 kHz Offset (Frac/Int) Synthesizer normalized In-Band SSB Phase noise Floor (Frac/Int) Synthesizer Fractional Spurs [1] Synthesizer Frequency Settling time (100 MHz Step) 16-Bit divider range (Int) 16-Bit divider range (Frac) From 13 gHz to 12.9 gHz Loop BW = 100 kHz n divider ratio 216+31 n divider ratio 2 -1 16 7 PLLS w/ Integrated VCO - SMt 7-2 12.4 4 2 V tUne = +5V V tUne = +5V 12.9 8 13.4 10 13 gHz dBm V MHz/V MHz pp MHz/V MHz/ °C dBc dBc dBc dBc/Hz dBc/Hz dBc/Hz dBc μs 190 5 6 1.2 25 18 35 V tUne = +5V Fvco = 12.9 gHz Fref = 50 MHz Fvco = 12.9 gHz Loop BW = 100 kHz -110 -95 / -98 -221 / -226 -65 104 32 36 65567 65535 REF Input Characteristics Max ref Input Frequency (3.3V) Min ref Input Frequency ref Input Sensitivity Max ref Input ref Input Capacitance 14-Bit ref divider range 16383 aC Coupled dC Coupled 0 200 225 100 500 200 700 VddIO 5 1 MHz kHz mVpp V pF [1] actual spur level is dependent on loop parameters and will increase at division ratios closest to integer boundaries. number listed is average value. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Electrical Specifications (Continued) Parameter Condition Min. typ. Max. Units Phase Detector Max Phase detector Frequency (Frac) Max Phase detector Frequency (Int) Min Phase detector Frequency 70 140 105 160 100 MHz MHz kHz Charge Pump Max Output Current Min Output Current Charge Pump noise Input referred 50 MHz ref. 2 500 -145 ma µa dBc/Hz Logic Inputs 7 PLLS w/ Integrated VCO - SMt VIH Input High Voltage VIL Input Low Voltage VddIO-0.4 0 VddIO 0.4 V V Logic Outputs VOH Output High Voltage VOL Output Low Voltage Serial Port Max Clock VddIO-0.4 0 50 VddIO 0.4 V V MHz Power Supply Voltages analog 3.3V Supplies: aVCC, VddPFd, aVdd, rVdd, VCCPS digital Internal Supplies: dVdd, dVddQ, dVddM digital I/O Supplies: VddIO analog 5V Supplies: VCCVCO, VddCP, VCCCP Logic I/O VCCCP must equal VddCP aVdd must equal dVdd 3 3 1.8 4.75 3.3 3.3 3.3 5 3.45 3.45 5.5 5.25 V V V V Power Supply Currents total Current Consumption (5V) total Current Consumption (3.3V) Power down Current [1] CSP disabled CSP enabled Measured with 10 gΩ meter 1.880 205 90 1 450 1.920 1.960 250 110 10 ma ma µa µa V Bias Reference Voltage [1] refers only to the Synthesizer portion of the HMC807LP6Ce 7-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz SSB Phase Noise vs. Frequency, Integer Mode -60 -70 12.4 GHz 12.9 GHz 13.4 GHz SSB Phase Noise vs. Temperature @ 12.9 GHz, Integer Mode -60 -70 +25 C +85 C -40 C PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -120 -130 -140 -150 10 2 PHASE NOISE (dBc/Hz) -80 -90 -100 -110 -120 -130 -140 -150 Fref = 50MHz Loop BW = 100kHz 2 3 4 5 6 Temp = 25C Fref = 50MHz Loop BW = 100kHz 3 4 5 6 7 10 10 10 10 10 10 10 10 10 10 10 7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) -60 -70 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 2 10 Temp = 25C Fref = 50MHz Loop BW = 100kHz 3 4 5 6 7 -80 -90 -100 -110 -120 -130 -140 -150 2 10 Fref = 10MHz Loop BW= 10kHz Fref = 50MHz Loop BW=100kHz 3 4 5 6 7 10 10 10 10 10 10 10 10 10 10 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Example of Cycle Slip Prevention Hop from 13.2 to 12.7 GHz 13.3 13.2 Typical Reference Sensitivity vs. Frequency, 3.3V [1] 20 10 R = Max, +25C R = Max, +85C FREQUENCY (GHz) 13.1 13 12.9 12.8 12.7 12.6 -10 0 10 20 30 40 50 CSP ON CSP OFF SENSITIVITY (dBm) 0 -10 -20 -30 -40 -50 R = 3, +25C R = 3, +85C 0 50 100 150 200 250 300 TIME (μSEC) FREQUENCY (MHz) [1] r refers to the reference path division ratio F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-4 PLLS w/ Integrated VCO - SMt SSB Phase Noise Fractional Spurs @ 12.902 GHz SSB Phase Noise vs. Reference Freq. & Loop BW @ 12.9 GHz, Integer Mode 7 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Frequency vs. Tuning Voltage, T = 25°C 14 Frequency vs. Tuning Voltage, Vcc = +5V 14 OUTPUT FREQUENCY (GHz) 13.2 12.8 12.4 12 11.6 11.2 10.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 Vcc=4.75V Vcc=5.0V Vcc=5.25V OUTPUT FREQUENCY (GHz) 13.6 13.6 13.2 12.8 12.4 12 11.6 11.2 10.8 0 1 2 3 4 5 6 7 8 9 10 11 12 13 +25C +85C -40C 7 PLLS w/ Integrated VCO - SMt 800 700 600 500 400 300 200 100 0 0 1 2 3 TUNING VOLTAGE (V) TUNING VOLTAGE (V) Sensitivity vs. Tuning Voltage, Vcc = +5V Output Power vs. Tuning Voltage, Vcc = +5V 12 10 OUTPUT POWER (dBm) SENSITIVITY (MHz/V) 8 +25C +85C -40C 6 4 2 +25C +85C -40C 0 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) TUNING VOLTAGE (V) Open Loop VCO SSB Phase Noise @ Vtune = +5V 0 Open Loop VCO SSB Phase Noise vs. Tuning Voltage 0 SSB PHASE NOISE (dBC/Hz) SSB PHASE NOISE (dBc/Hz) -20 -40 -60 -80 -100 -120 -140 -160 10 3 -20 10 kHz Offset 100 kHz Offset +25C +85C -40C -40 -60 -80 -100 -120 10 4 10 5 10 6 10 7 1 2 3 4 5 6 7 8 9 10 11 12 13 OFFSET FREQUENCY (Hz) TUNING VOLTAGE (V) 7-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Pin Descriptions Pin number 1, 9 - 13, 22, 36 2 - 4, 7, 37, 39 5 8 40 6 14 Function n/C gnd [1] gnd VCCVCO2 [2] VCCVCO1 VtUne aCg description no Connection. these pins may be connected to rF/dC ground. Performance will not be affected. these pins must be connected to rF/dC ground these pins and package bottom must be connected to rF/dC ground +5V Power Supply for VCO Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. aC ground. this pin must be connected to an external capacitor to ground. analog Power supply pin for the rF Section. a decoupling capacitor to the ground plane should be placed as close as possible to this pin. nominally 3.3V +5V Power Supply for charge pump digital section +5V Power Supply for the charge pump analog section Charge pump output analog Power supply for the phase frequency detector, nominally 3.3V external bypass decoupling for precision bias circuits, 1.920V ±20 mV is generated internally analog Power supply for analog ref paths, nominally 3.3V reference input (negative or aC coupled to gnd) reference input (Positive) ref path supply digital supply for Substrate, nominally 3.3V Chip enable Serial port latch enable input Serial port clock input Serial port data input Power supply pin for internal digital circuitry. nominally 3.3V Power Supply for digital I/O driver Lock detect, Main Serial data Output or VCO Serial Port data Out analog Power Supply for Prescaler, nominally 3.3V digital Power Supply for M-Counter, nominally 3.3V rF output (aC coupled). 15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 35 38 aVCC VddCP VCCCP CP VddPFd BIaS [3] aVdd reFn reFP rVdd dVddQ Ce Sen SCK SdI dVdd VddIO Ld_SdO VCCPS dVddM rFOUt 7 PLLS w/ Integrated VCO - SMt 7-6 [1] this pin is not connected internally, however, this pin must be connected to gnd to maintain product family pin for pin compatibility. [2] this pin is not connected internally, however, this pin must be connected to Vcc to maintain product family pin for pin compatibility. [3] BIaS ref voltage (pin 20) cannot drive an external load, and must be measured with a 10 gOhm meter such as agilent 34410a; a typical 10 Mohm dVM will read erroneously. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Pin Schematic Equivalents Pins equivalent Schematic rFOUt VCCVCO1 7 PLLS w/ Integrated VCO - SMt VtUne gnd Sen, Ce, SCK, SdI Ld_SdO CP 7-7 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Pin Schematic Equivalents (Continued) Pins equivalent Schematic Bias 7 PLLS w/ Integrated VCO - SMt 7-8 reFn, reFP F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Evaluation Circuit 3VDIGITAL R8 100K 2 3VANALOG C12 100NF C10 10PF C8 10PF C9 100NF 3VDIGITAL CEN 3VDIGITAL C14 100NF C13 10PF a B C d R1 100K JP1 1 J3 1 RFout 2 C15 100PF R20 1K 50 Ohm Co-Planar Trace 7 PLLS w/ Integrated VCO - SMt TP6 SDO 5016 TP5 SYNTH C32 4.7UF C38 1NF 2 NC NC NC ACG AVCC VDDCP VCCCP CP VDDPFD BIAS GND 5016 1 2 3 4 5 6 7 8 9 10 VCCVCO1 GND RFOUT GND NC DVDDM VCCPS LD_SDO VDDIO DVDD JP2 LD 5VVCO C4 4.7UF 1 C1 1NF 40 39 38 37 36 35 34 33 32 31 NC GND GND GND GND VTUNE GND VCCVCO2 NC NC U1 SDI SCK SEN CE DVDDQ RVDD REFP REFN NC AVDD 30 29 28 27 26 25 24 23 22 21 e F g H C34 100NF C21 1NF 11 12 13 14 15 16 17 18 19 20 JP3 C31 1 C35 100NF R2 120 100PF R23 C65 R27 DEPOP 0 L1 R28 C61 3.9NF DEPOP DEPOP DEPOP R21 30 R3 1K C62 DEPOP I R12 DEPOP R4 620 C64 DEPOP R13 200 C37 39NF C33 1.2NF J +15V TP4 FB4 C57 22UF 1000 FB3 1000 THS4031IDGN C58 4.7UF C39 1NF 6 C63 DEPOP K R25 5016 TP3 7 2 U5 4 3 DEPOP GND 5016 DEPOP R26 R22 R15 10K C60 1NF R14 10K 0 L JP6 1 2 M 7-9 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Evaluation Circuit (Continued from page 9) 3VDIGITAL C9 100NF Header to USB Board J1 a B C d R1 100K SCK SDI SDO SEN CEN 1 3 5 7 9 11 2 4 6 8 10 12 NC NC NC NC 3VDIGITAL TLW-106-05-T-D C5 10PF C7 100NF 3VDIGITAL 3VANALOG C2 10PF C3 100NF 5.5V GND TP2 5016 TP1 C42 100NF 7 FB2 1000 C59 4.7UF FB1 PLLS w/ Integrated VCO - SMt 1 e F g H C34 100NF R6 C35 100NF R2 120 56 R7 120 50 Ohm Trace C29 100NF REFin 1 J2 5016 1000 C40 100NF TCXO 3 FOUT Y2 GND 2 VDD VC 4 1 R9 C6 10PF C28 100NF R24 10 DEPOP 3VTCXO R11 4.02K JP5 1 2 R41 1K 6 U9 LP3878MR-ADJ SD ADJ VIN BPASS VOUT GND 8 4 1 3 5VVCO C36 100NF C68 4.7UF R40 4.02K C67 1.2NF C41 100NF 5 C73 10NF C30 DEPOP R10 0 I C16 10PF C18 100NF 3VANALOG R17 1K 6 U8 LP3878MR-ADJ SD ADJ VIN BPASS VOUT GND 8 4 1 3 J 3VANALOG C22 10PF C23 100NF R16 4.02K C44 1.2NF C43 100NF 5 5VCP C46 100NF C45 4.7UF C47 10NF K 5VCP C24 10PF C25 100NF U2 LP5900-3_3V L 3VANALOG C26 10PF C27 100NF 3VANALOG C19 10PF C20 100NF 1 VOUT VIN 6 4 GND EN 3 R5 10K C11 100NF 3VDIGITAL U4 LP5900-3_3V 1 M 5VCP C51 10PF C52 100NF VOUT VIN 6 4 GND EN 3 R18 10K C50 100NF 3VTCXO C55 10PF C56 100NF U6 LP5900-3_3V 1 VOUT VIN GND EN 3 6 4 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com R19 10K C54 100NF JP4 2 7 - 10 HMC807LP6CE r to USB Board J1 1 3 5 7 9 11 2 4 6 8 10 12 NC NC NC NC v03.0411 3VDIGITAL FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz TLW-106-05-T-D C7 100NF 3VDIGITAL Evaluation Circuit (Continued from page 10) 3VANALOG C3 100NF 5.5V GND TP2 FB2 1000 C42 100NF C59 4.7UF FB1 1000 5016 TP1 Trace C29 100NF REFin 1 J2 5016 TCXO 3 FOUT Y2 GND 2 VDD VC 4 1 R9 C6 10PF C28 100NF R24 10 DEPOP 3VTCXO R11 4.02K JP5 1 2 R41 1K 6 U9 LP3878MR-ADJ SD ADJ VIN BPASS VOUT GND 8 4 1 3 7 PLLS w/ Integrated VCO - SMt C18 100NF 5VVCO C36 100NF C68 4.7UF R40 4.02K C67 1.2NF C41 100NF C73 10NF C74 4.7UF 5 C30 DEPOP R10 0 3VANALOG R17 1K 6 U8 LP3878MR-ADJ SD ADJ VIN BPASS VOUT GND 8 4 1 3 3VANALOG R16 4.02K C44 1.2NF C43 100NF C47 10NF C48 4.7UF 5 C23 100NF 5VCP C46 100NF C45 4.7UF 5VCP U2 LP5900-3_3V C25 100NF 3VANALOG 3VANALOG C19 10PF C20 100NF 1 VOUT VIN 6 4 C27 100NF GND EN 3 R5 10K C11 100NF C17 4.7UF 3VDIGITAL C51 10PF C52 100NF U4 LP5900-3_3V 1 VOUT VIN GND EN 3 6 4 5VCP R18 10K C50 100NF C49 4.7UF 3VTCXO C55 10PF C56 100NF U6 LP5900-3_3V 1 VOUT VIN GND EN 3 6 4 R19 10K 1 C54 100NF JP4 2 C53 4.7UF 7 - 11 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Absolute Maximum Ratings nominal 3.3V Supplies to gnd nominal digital Supply to 3.3V analog Supply nominal 5V Supply to gnd Vtune Storage temperature Max Peak reflow temperature eSd rating -0.3V to +3.6V -0.3V to +0.3V -0.3 to +5.5V 0 to +15V -65 to +150°C 260 °C Class 1a Reliability Information Junction temperature to Maintain 1 Million Hour MttF nominal Junction temperature (t=85 °C) thermal resistance (Junction to gnd Paddle, 5V Supply) Operating temperature 135 °C 120 °C 34.2 °C/W -40 to +85°C 7 PLLS w/ Integrated VCO - SMt Package Marking [1] H807 XXXX Outline Drawing nOteS: 1. LeadFraMe MaterIaL: COPPer aLLOY 2. dIMenSIOnS are In InCHeS [MILLIMeterS]. 3. Lead SPaCIng tOLeranCe IS nOn-CUMULatIVe 4. Pad BUrr LengtH SHaLL Be 0.15 mm MaXIMUM. Pad BUrr HeIgHt SHaLL Be 0.05 mm MaXIMUM. 5. PaCKage WarP SHaLL nOt eXCeed 0.05 mm. 6. aLL grOUnd LeadS and grOUnd PaddLe MUSt Be SOLdered tO PCB rF grOUnd. 7. reFer tO HIttIte aPPLICatIOn nOte FOr SUggeSted PCB Land Pattern. Package Information Part number HMC807LP6Ce Package Body Material roHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL rating MSL3 [1] 4-digit lot number XXXX F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 12 HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz Evaluation PCB 7 PLLS w/ Integrated VCO - SMt the circuit board used in the application should use rF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. a sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from Hittite upon request. 7 - 13 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC807LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 12.4 - 13.4 GHz List of Materials for Evaluation PCB 127283 [1] Item J1 J2, J3 JP1 - JP6 C1, C21, C38 - C39, C60 C2, C5, C6, C8, C10, C13, C16, C19, C22, C24, C26, C51, C55 C3, C7, C9, C11, C12, C14, C18, C20, C23, C25, C27 - C29, C34 - C36, C40 - C43, C46, C50, C52, C54, C56 C4, C17, C32, C45, C48, C49, C53, C68, C74 C15, C31 C33, C44, C67 C37 C47, C73 C57 C58, C59 C61 FB1 - FB4 r1, r8 r2, r7 r3, r17, r20, r41 r4 r5, r14, r15, r18, r19 r6 r9 r10, r22, r23 r11, r16, r40 r13 r21 tP1 - tP6 U1 U2, U4, U6 U5 U8, U9 Y2 PCB [2] description dual row terminal Strip PCB Mount SMa rF Connector Single row terminal Strip 1000 pF Capacitor, 0402 Pkg. 10 pF Capacitor, 0402 Pkg. 0.1 µF Capacitor, 0402 Pkg. 4.7 µF Capacitor, 0805 Pkg. 100 pF Capacitor, 0402 Pkg. 1200 pF Capacitor, 0402 Pkg. 0.039 µF Capacitor, 0603 Pkg. 10,000 pF Capacitor, 0402 Pkg. 22 µF tantalum Capacitor, Case d 4.7 µF tantalum Capacitor, Case B 3900 pF Capacitor, 0402 Pkg. 1000 Ohm 200 ma Ferrite Chip, 0805 Pkg. 100k Ohm resistor, 0402 Pkg. 120 Ohm resistor, 0402 Pkg. 1k Ohm resistor, 0402 Pkg. 620 Ohm resistor, 0402 Pkg. 10k Ohm resistor, 0402 Pkg. 56 Ohm resistor, 0402 Pkg. 10 Ohm resistor, 0402 Pkg. Zero Ohm resistor, 0402 Pkg. 4.02k Ohm resistor, 0402 Pkg. 200 Ohm resistor, 0402 Pkg. 30 Ohm resistor, 0402 Pkg. test Point PC Compact SMt HMC764LP6Ce Fractional-n PLL, with Integrated VCO Low noise 3.3V, 100 ma Linear regulator Low noise Op-amp, tHS4031Idgn 5V, 800ma Voltage regulator 3.3V, 50 MHz VCXO Crystal Oscillator 125536 evaluation Board 7 PLLS w/ Integrated VCO - SMt 7 - 14 [1] reference this number when ordering complete evaluation PCB [2] Circuit Board Material: rogers 4350 or arlon 25Fr and Fr4 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com