HMC822LP6CE

HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Features • RF Bandwidth: 665 - 825, 1330 - 1650, 2660 - 3300 MHz • Ultra Low Phase Noise -105 dBc/Hz in Band Typ. • Figure of Merit (FOM) -227 dBc/Hz • < 180 fs RMS Jitter • 24-bit Step Size, Resolution 3 Hz typ • Exact Frequency Mode • Built-in Digital Self Test • 40 Lead 6x6 mm SMT Package: 36 mm2 Typical Applications 7 PLLS w/ INTEGRATED VCO - SMT • Cellular/4G Infrastructure • Repeaters and Femtocells • Communications Test Equipment • CATV Equipment • Phased Array Applications • DDS Replacement • Very High Data Rate Radios Functional Diagram 7-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz General Description The HMC822LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with a tri-band output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. For theory of operation and register map refer to the “ PLLs w/ Integrated VCOs - RF VCOs Operating Guide”. To view the Operating Guide, please visit www.hittite.com and choose HMC822LP6CE from the “Search by Part Number” pull down menu. Electrical Specifications, TA = +25° C Parameter Condition Min. Typ. Max. Units RF Output Characteristics VCO Frequency at PLL Input RF Output Frequency at f VCO/2 RF Output Frequency at f VCO RF Output Frequency at 2f VCO RF Output Power at f VCO/2 RF Output Power at f VCO RF Output Power at 2f VCO VCO Tuning Sensitivity VCO Supply Pushing RF Output fo/2 Harmonic RF Output 3fo/2 Harmonic RF Output 2nd Harmonic RF Output 5fo/2 Harmonic RF Output 3rd Harmonic RF Output 7fo/2 Harmonic Measured at fo, 2V Measured at fo, 2V Doubler Mode Doubler Mode fo/2/fo/2fo Doubler Mode fo/2/fo/2fo Doubler Mode -2 -22 -50 1330 665 1330 2660 9 2.5 -9 11 6.5 -4 15 1.5 -18 -41 1650 825 1650 3300 13 10.5 1 MHz MHz MHz MHz dBm dBm dBm MHz/V MHz/V dBc dBc dBc dBc dBc dBc -26 / -30 / -42 -22 / -19 / -36 -60 -56 -27 / -40 / -60 -23 / -32 / -51 -65 -61 RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 Fractional nominal divide ratio varies (-3 / +4) dynamically max 524,287 524,283 REF Input Characteristics Synthesizer phase noise can degrade by about 5 dB when operating with a reference frequency near the low end of this range. AC Coupled Max Ref Input Frequency 10 50 200 MHz Ref Input Range Ref Input Capacitance 14-Bit R-Divider Range 1 2 3.3 5 Vpp pF 1 16,383 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-2 PLLS w/ INTEGRATED VCO - SMT VPPCP, VDDCP, VCC1, VCC2 = 5V ±4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V ±6% GNDCP = GNDLS = Ground Paddle = 0V 7 HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Electrical Specifications (Continued) Parameter Condition [1] Min. Typ. Max. Units Phase Detector (PD) PD Frequency Fractional Feedback Mode PD Frequency Fractional Feedforward Mode (and Register 6 [17:16] = 10) PD Frequency Integer Mode [1] 0.1 0.1 0.1 100 80 125 MHz MHz MHz Charge Pump Output Current Charge Pump Gain Step Size PD/Charge Pump SSB Phase Noise 50 MHz Ref, Input Referred -141 Add 1 dB for Fractional Add 3 dB for Fractional -149 -153 dBc/Hz dBc/Hz dBc/Hz 0.02 20 2.54 mA µA 7 PLLS w/ INTEGRATED VCO - SMT 1 kHz 10 kHz 100 kHz Logic Inputs VIH Input High Voltage VIL Input Low Voltage DVDD3V-0.4 0 DVDD3V 0.4 V V Logic Outputs VOH Output High Voltage VOL Output Low Voltage DVDD3V-0.4 0 DVDD3V 0.4 V V Power Supply Voltages Analog 3.3V Supplies Digital Supply Analog 5V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD DVDD3V VPPCP, VDDCP, VCC1, VCC2 3.0 3.0 4.8 3.3 3.3 5 3.5 3.5 5.2 V V V Power Supply Currents +5V Analog Charge Pump +5V VCO Core and PLL Buffer +5V VCO Divider and RF Buffer +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz VPPCP, VDDCP VCC2 VCC1 AVDD, VCCHF, VCCPS, VCCPD, RVDD DVDD3V Reg 01h=0, Crystal Not Clocked Reg 01h=0, Crystal Clocked 100 MHz 5.3 56 36 45 6.5 10 10 200 mA mA mA mA mA µA µA Power on Reset Typical Reset Voltage on DVDD Min DVDD Voltage for No Reset Power on Reset Delay 1.5 250 700 mV V µs Note 1: This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less. 7-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Electrical Specifications (Continued) Parameter Condition Min. Typ. Max. Units VCO Open Loop Phase Noise at fo/2 10 kHz Offset 100 kHz Offset 1 MHz Offset 10 MHz Offset 100 MHz Offset -95 -124 -148 -162 -163 -89 -121 -145 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz VCO Open Loop Phase Noise at fo 10 kHz Offset 100 kHz Offset 1 MHz Offset 10 MHz Offset 100 MHz Offset -89 -118 -142 -162 -164 -83 -115 -139 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz 7 PLLS w/ INTEGRATED VCO - SMT 7-4 VCO Open Loop Phase Noise at 2fo 10 kHz Offset 100 kHz Offset 1 MHz Offset 10 MHz Offset 100 MHz Offset -83 -112 -136 -155 -160 -83 -115 -139 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco/2 Integer, 25 MHz PD Integer, 25 MHz PD Integer, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 kHz Offset 10 kHz Offset 100 kHz Offset -113 -118 -118 -109 -111 -116 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Closed Loop Phase Noise PLL + VCO at fvco Integer, 25 MHz PD Integer, 25 MHz PD Integer, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 kHz Offset 10 kHz Offset 100 kHz Offset -107 -112 -112 -103 -105 -110 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Closed Loop Phase Noise PLL + VCO at 2fo Integer, 25 MHz PD Integer, 25 MHz PD Integer, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD Fractional, 25 MHz PD 1 kHz Offset 10 kHz Offset 100 kHz Offset 1 kHz Offset 10 kHz Offset 100 kHz Offset Normalized 1 Hz Measured w/ 50 MHz PD at 30 kHz Offset Measured w/ 50 MHz PD at 30 kHz Offset -229 -227 dBc/Hz dBc/Hz -101 -106 -106 -97 -99 -104 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Figure of Merit Integer Mode Fractional Mode F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Closed Loop Integer Phase Noise -80 -90 Typical Closed Loop Fractional Phase Noise [1] -80 -90 PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) -100 -110 -120 -130 -140 -150 -160 -170 -180 2 10 10 3 -100 -110 -120 -130 -140 -150 -160 -170 851 MHz FF 1701 MHz FF 3402 MHz FF 800 MHz FF 1650 MHz FF 3200 MHz FF 10 4 10 5 10 6 10 7 10 8 -180 2 10 10 3 10 4 10 5 10 6 10 7 10 8 7 PLLS w/ INTEGRATED VCO - SMT -40 -60 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Free Running Phase Noise Typical VCO Sensitivity vs. Cap @ Fo Voltage TUNE VOLTAGE AFTER CALABRATION (V) 5 PHASE NOISE (dBc/Hz) -80 -100 -120 -140 -160 -180 10 3 750 MHz FF 1500 MHz FF 3000 MHz FF 4 fmin 3 31 15 fmax 0 2 1 10 4 10 5 10 6 10 7 10 8 0 920 960 1000 1040 1080 1120 1160 OFFSET FREQUENCY (Hz) VCO FREQUENCY Free Running VCO Phase Noise Over Temperature -110 -120 100 kHz Offset +27C +85C -40C Typical VCO Sensitivity vs. Cap @ Fo Voltage 60 TUNING CAP 31, 1316 MHz AT 2V TUNING CAP 15, 1466 MHz AT 2V TUNING CAP 0, 1685 MHz AT 2V 50 PHASE NOISE (dBc/Hz) -140 1 MHz Offset kvco (MHz/V) -130 40 30 Typical Operating Range -150 20 -160 10 MHz Offset 10 -170 1300 1350 1400 1450 1500 1550 1600 1650 1700 0 0 1 2 3 4 5 FREQUENCY (MHz) TUNING VOLTAGE (V) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385µA Offset. 7-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Typical Output Power - Narrow Band Match 20 15 Divide-by-2 Fundamental 10 5 0 -5 -10 -15 600 700 800 9001000 -40C 27C 85C Doubler Figure of Merit NORMALIZED PHASE NOISE (dBc/Hz) -200 OUTPUT POWER (dBm) -210 Typ FOM vs Offset -220 FOM 1/f Noise -230 FOM Floor 2000 3000 4000 -240 2 10 10 3 10 4 10 5 10 6 OUTPUT FREQUENCY (MHz) FREQUENCY OFFSET (Hz) 7 PLLS w/ INTEGRATED VCO - SMT F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-6 HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Pin Descriptions Pin Number 1 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 34, 37, 38 3 4 7 10 15 Function AVDD Description DC Power Supply for analog circuitry. The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. Power Supply for charge pump analog section Charge Pump Output Power Supply for the charge pump digital section Reference Supply Reference Oscillator Input DC Power Supply for Digital (CMOS) Circuitry Chip Enable. Connect to logic high for normal operation. VCO Varactor. Tuning Port Input. VCO Analog Supply 2 VCO Analog Supply 1 RF Positive Output RF Negative Output PLL Serial Port Enable (CMOS) Logic Input PLL Serial Port Data (CMOS) Logic Input PLL Serial Port Clock (CMOS) Logic Input Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) DC Power Supply for Analog Circuitry DC Power Supply for Analog Prescaler DC Power Supply for Phase Detector External bypass decoupling for precision bias circuits. Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10GΩ meter such as Agilent 34410A, normal 10MΩ DVM will read erroneously. N/C VPPCP CP VDDCP RVDD XREFP DVDD3V CEN VTUNE VCC2 VCC1 RF_N [1] RF_P [1] 7 PLLS w/ INTEGRATED VCO - SMT 16 17 23 25 27 28 29 30 31 32 33 35 36 39 SEN SDI SCK LD_SDO VCCHF VCCPS VCCPD 40 BIAS [1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together. 7-7 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS VPPCP, VDDCP, VCC1 VCC2 Operating Temperature Storage Temperature Maximum Junction Temperature Thermal Resistance (RTH) ( junction to ground paddle) Reflow Soldering Peak Temperature Time at Peak Temperature ESD Sensitivity (HBM) 260°C 40 sec Class 1B -0.3V to +3.6V -0.3V to +5.8V -0.3V to +5.5V -40°C to +85°C -65°C to 125°C 125 °C 20 °C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 7 PLLS w/ INTEGRATED VCO - SMT H822 XXXX Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number HMC822LP6CE Package Body Material RoHS-compliant Low Stress Injection Molded Plastic Lead Finish 100% matte Sn MSL Rating MSL1 Package Marking [1] [1] 4-Digit lot number XXXX F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-8 HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Evaluation PCB, fo & fo/2 Modes 7 PLLS w/ INTEGRATED VCO - SMT The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC822LP6CE from the “Search by Part Number” pull down menu to view the product splash page. 7-9 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz List of Materials for Evaluation PCB 127827, fo & fo/2 Mode [1] Item J1, J2 J3 J4 - J6 C1, C15 - C17, C25 C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 C4, C13 C5, C33 C8 C19 - C24, C28, C30, C32, C34 C26 C29 C35 C36 C37, C38 C39 - C42, C44 R1, R2, R5, R8, R11, R15, R18, R19, R21, R24 R3, R4 R6, R7 R12, R20, R29 R22, R25 R26 - R28 L1 L2, L3 TP3, TP4 U1 U2 Y1 PCB [2] Description PCB Mount SMA RF Connector Dual Row Terminal Strip Connector Header 10 µF Capacitor, 0805 Pkg. 0.47 µF Capacitor, 0402 Pkg. 22 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. 1.5 pF Capacitor, 0402 Pkg. 0.1 µF Capacitor, 0402 Pkg. 1 µF Capacitor, 0603 Pkg. 47 pF Capacitor, 0402 Pkg. 3300 pF Capacitor, 0402 Pkg. 270 pF Capacitor, 0402 Pkg. 68 pF Capacitor, 0402 Pkg. 4.7 µF Tantalum Capacitor, 0805 Pkg 0 Ohm Resistor, 0402 Pkg. 1 Ohm Resistor, 0402 Pkg. 0 Ohm Resistor, 0805 Pkg. 51 Ohm Resistor, 0402 Pkg. 20 kOhm Resistor, 0402 Pkg. 1k Ohm Resistor, 0402 Pkg. 8.2 nH Inductor, 0402 Pkg. 47 nH Inductor, 0402 Pkg. Test Point PC Compact SMT HMC822LP6CE PLL with Integrated VCO HMC860LP3E Low Noise Quad Linear Regulator 3.3V, 50 MHz VCXO Crystal Oscillator 125998 Evaluation Board 7 PLLS w/ INTEGRATED VCO - SMT 7 - 10 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz Evaluation PCB, 2xfo Mode 7 PLLS w/ INTEGRATED VCO - SMT The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC822LP6CE from the “Search by Part Number” pull down menu to view the product splash page. 7 - 11 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC822LP6CE v04.1010 FRACTIONAL-N SYNTHESIZER w/ INTEGRATED VCO 665 - 825, 1330 - 1650, 2660 - 3300 MHz List of Materials for Evaluation PCB 128159, 2xfo Mode Item J1, J2 J3 J4 - J6 C1, C15 - C17, C25 C2, C3, C6, C12, C14, C18, C27, C43, C45 C4, C13 C5, C33 C7, C11 C8 C19 - C24, C28, C30, C32, C34 C26 C29 C31 C35 C36 C37, C38 C39 - C42, C44 C46 C47 R1, R2, R8, R11, R15, R18, R19, R21, R24 R3, R4 R12, R20, R23, R29 R13, R14, R30 R22, R25 R26 - R28 R31 R32, R33 L1 L2, L3 L4 TP1 - TP4 U1 U2 Y1 PCB [2] Description PCB Mount SMA RF Connector Dual Row Terminal Strip Connector Header 10 µF Capacitor, 0805 Pkg. 0.47 µF Capacitor, 0402 Pkg. 22 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. 470 nF Capacitor, 0402 Pkg. 8.2 pF Capacitor, 0402 Pkg. 0.1 µF Capacitor, 0402 Pkg. 1 µF Capacitor, 0603 Pkg. 1 pF Capacitor, 0402 Pkg. 0.5 pF Capacitor, 0402 Pkg. 3300 pF Capacitor, 0402 Pkg. 270 pF Capacitor, 0402 Pkg. 68 pF Capacitor, 0402 Pkg. 4.7 µF Tantalum Capacitor, 0805 Pkg 27 pF Capacitor, 0402 Pkg. 47 pF Capacitor, 0402 Pkg. 0 Ohm Resistor, 0402 Pkg. 1 Ohm Resistor, 0402 Pkg. 51 Ohm Resistor, 0402 Pkg. 220 kOhm Resistor, 0402 Pkg. 20 kOhm Resistor, 0402 Pkg. 1 kOhm Resistor, 0402 Pkg. 0 Ohm Resistor, 0201 Pkg. 0 Ohm Resistor, 0805 Pkg. 10 nH Inductor, 0402 Pkg. 47 nH Inductor, 0402 Pkg. 1.8 nH Inductor, 0402 Pkg. Test Point PC Compact SMT HMC822LP6CE PLL with Integrated VCO HMC860LP3E Low Noise Quad Linear Regulator 3.3V, 50 MHz VCXO Crystal Oscillator 127729 Evaluation Board [1] 7 PLLS w/ INTEGRATED VCO - SMT 7 - 12 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com