HMC861LP3E

HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Features Low noise Floor: -152 dBc/Hz at 100 kHz offset Programmable Frequency Divider, n = 1 or 3 Wide Bandwidth 100 MHz to 13 GHz 16 Lead 3X3 mm sMt Package: 9mm 2 4 Frequency DiviDers & Detectors - sMt Typical Applications the HMc861LP3e is ideal for: • Satellite Communication Systems • Point-to-Point & Point-to-Multi-Point Radios • Military Applications • Test Equipment Functional Diagram General Description the HMc861LP3e is a low noise programmable frequency divider in a 3 x 3 mm leadless surface mount package. the divider can be programmed to divide from n = 1,3 in the 100 MHz to 13 GHz input frequency range. the low phase noise and wide frequency range make this device ideal for high performance and wide band communication systems. Electrical Specifications, TA = +25 °C, Vcc1 = Vcc2 = +5V Parameter RF Input Characteristics Max rF input Frequency Min rF input Frequency [1] rF input Power range Divider Output Characteristics output Power Divider ratio n ssB Phase noise @ 100 kHz offset ssB Phase noise @ 100 kHz offset Logic Inputs viH input High voltage viL input Low voltage Power Supplies vcc1, vcc2 Current Consumption icc control Bits n = 1, s0 = L n = 3, s0 = H 125 180 1 mA mA Bit Analog Supply (See pin description table) 4.75 5 5.25 v 3 0 5 0.4 v v Fin = 6 GHz, Pin = 0 dBm, n = 1 Fin = 6 GHz, Pin = 0 dBm, n = 3 (see the Pout plots for each division ratio) 1 -152 -153 2 3 dBc/Hz dBc/Hz dBm sine Wave or square Wave input sine Wave or square Wave input -10 0 13 0.1 10 GHz GHz dBm conditions Min. typ. Max. units [1] square wave input waveform is recommended below 400 MHz for best phase noise performance. if sine wave input waveform is used below 400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance. 4-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Divide-by-1 Output Power vs. Temperature, Pin = 0 dBm 6 4 Input Sensitivity vs. Temperature 15 10 4 Frequency DiviDers & Detectors - sMt 4-2 INPUT POWER (dBm) 5 0 -5 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C OUTPUT POWER (dBm) 2 0 -10 -15 -20 -25 0 2 4 6 -2 +25C +85C -40C 0 2 4 6 8 10 12 14 -4 -6 8 10 12 14 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 Phase Noise vs. Temperature, Fin = 6 GHz, Pin = 0 dBm -120 SSB PHASE NOISE (dBc/Hz) -130 SSB PHASE NOISE (dBc/Hz) 100MHz SQ 100MHz SINE 6 GHz 13 GHz -130 +25C +85C -40C -140 -140 -150 -150 -160 -160 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm 10 0 Reverse Leakage, Pin = 0 dBm 0 -10 OUTPUT LEVEL (dBm) -10 POWER LEVEL (dBm) -20 -20 -30 -30 Pfeedthru 3rd Harmonic -40 -40 Both Output Ports Terminated One Output Port Terminated -50 0 2 4 6 8 10 12 14 -50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Divide-by-3 4 Frequency DiviDers & Detectors - sMt Input Sensitivity vs. Temperature 15 10 Output Power vs. Temperature, Pin = 0 dBm 6 4 INPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C OUTPUT POWER (dBm) 2 0 -2 +25C +85C -40C 0 2 4 6 8 10 12 14 -4 -6 2 4 6 8 10 12 14 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 100MHz SQ 100MHz SINE 6 GHz 13 GHz Phase Noise vs. Temperature, Fin = 6 GHz, Pin = 0 dBm -120 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) -130 -130 +25C +85C -40C -140 -140 -150 -150 -160 -160 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY(Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm 10 0 Reverse Leakage, Pin = 0 dBm 0 -10 -20 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) -10 -20 -30 -40 -50 -60 Pfeedthru 3rd Harmonic 0 2 4 6 8 10 12 14 POWER LEVEL (dBm) -30 -40 -50 -60 -70 -80 -90 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) 4-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Icc vs. Vcc 225 200 4 Frequency DiviDers & Detectors - sMt 4-4 OPERATING CURRENT (mA) 175 150 125 N=1 N=3 75 4.7 4.8 4.9 5 5.1 5.2 5.3 100 Vcc (V) Absolute Maximum Ratings rF input Power supply voltage (vcc) control inputs (s0) storage temperature esD sensitivity (HBM) 13 dBm 5.5v 5.5v -65 to +125 °c Class 1A Digital Control Input Voltages state Low High s0 0 to 0.4v 3v to 5v Programming Truth Table for Frequency Division Ratios s0 0 1 Divider ratio (n) 1 3 0 = Logic Low 1 = Logic High note: vcc1, vcc2 must be applied before logic. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Reliability Information Junction temperature to Maintain 1 Million Hour MttF nominal Junction temperature (t = 85 °c and Pin = 10 dBm)) thermal resistance (Junction to GnD Paddle, 5v supply) operating temperature 150 °c 108 °c 25 °c/W -40 to +85 °c F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Outline Drawing 4 Frequency DiviDers & Detectors - sMt notes: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST Be soLDereD to PcB rF GrounD. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part number HMc861LP3e Package Body Material roHs-compliant Low stress injection Molded Plastic Lead Finish 100% matte sn MsL rating MsL1 [2] Package Marking [1] 861 XXX X [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °c 4-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Pin Description Pin number 1, 4, 8, 9, 12, 14, 15 Function GnD Description Ground: Backside of package has exposed metal ground slug which must be connected to rF/Dc ground. interface schematic 4 Frequency DiviDers & Detectors - sMt 4-6 2 in rF input must be Dc blocked. 3 nin rF input 180° out of phase with pin 2 for differential operation. AC ground for single ended operation. 5 s0 cMos compatible division ratio control bit. see programming truth table. 6 GnD internally connected to circuitry, must be connected to rF/Dc ground for proper operation. the pins are not connected internally; however, all data shown herein was measured with these pins connected to rF/Dc ground externally. 7 nc 10 nout Divider output 180° out of phase with pin 11. rF output must be Dc blocked. 11 out Divided output. rF output must be Dc blocked. 13, 16 vcc1, vcc2 supply voltage 5v. connect both pins to +5v supply. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Evaluation PCB Schematic 4 Frequency DiviDers & Detectors - sMt 4-7 notes: 1. the shorting link from PcB ground to pin 6 must be installed for proper operation. 2. Capacitors C1, C2, C3, and C4 are broadband multilayer capacitors, American Technical Cermaics part number ATC530L. The 100 nF capacitance value is per ATC datasheet. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC861LP3E v00.0310 13 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 3) Evaluation PCB 4 Frequency DiviDers & Detectors - sMt 4-8 List of Materials for Evaluation PCB Eval01-HMC861LP3E item J1 - J3 J4 c1 - c4 c5, c6 c7, c8 r3 vcc1, vcc2 u1 PcB [2] Description Connector, SMA, Female Dc connector Header, Molex 2mm 100 nF capacitor, Broadband, 0402 1000 pF capacitor, 0402 Pkg. 4.7 uF capacitor, 1206 10 k ohm resistor, 0402 Dc Pin, 0.040" Dia. HMc861LP3e, Programmable Divider 119349 evaluation Board [1] the circuit board used in the application should use rF circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from Hittite upon request. [1] reference this number when ordering complete evaluation PcB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com