HMC862LP3E

HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Features Low noise Floor: -153 dBc/Hz at 100 kHz offset Programmable Frequency Divider, n = 1, 2, 4, 8 Wide Bandwidth: 100 MHz to 15 GHz 16 Lead 3X3 mm sMt Package: 9mm 2 4 Frequency DiviDers & Detectors - sMt Typical Applications the HMc862LP3e is ideal for: • satellite communication systems • Point-to-Point & Point-to-Multi-Point radios • Military Applications • test equipment Functional Diagram General Description the HMc862LP3e is a low noise programmable frequency divider in a 3x3 mm leadless surface mount package. the divider can be programmed to divide from n=1, 2, 4, 8 in the 100 MHz to 15 GHz input frequency range. the low phase noise, wide frequency range and flexible division ratio make this device ideal for high performance and wide band communication systems. Electrical Specifications, TA = +25° C, Vcc1 = Vcc2 = +5V Parameter RF Input Characteristics Max rF input Frequency Min rF input Frequency rF input Power range (n = 1) rF input Power range (n = 2, 4, 8) Divider Output Characteristics output Power (n = 1) output Power (n = 2, 4, 8) Divider ratio n ssB Phase noise @ 100 kHz offset Logic Inputs viH input High voltage viL input Low voltage Power Supplies vcc Current Consumption n = 1, s0 = L, s1 = L, s2 = L icc n = 2, s0 = H, s1 = L, s2 = L n = 4, s0 = H, s1 = H, s2 = L n = 8, s0 = H, s1 = H, s2 = H control Bits 106 143 153 162 3 mA mA mA mA Bit Analog supply 4.75 5 5.25 v 3 0 5 0.4 v v Fin = 6 GHz, Pin = 0 dBm, n = 2 (see the Pout plot for n = 1) [2] (see the Pout plots for each division ratio) -2 to +3 2 1, 2, 4, 8 -153 dBc/Hz dBm dBm sine Wave or square Wave input sine Wave or square Wave input [1] sine Wave or square Wave input [1] [2] Fin < 8 GHz sine Wave or square Wave input [1] [2] Fin > 8 GHz sine Wave or square Wave input [1] -10 -10 -10 15 0.1 10 0 10 GHz GHz dBm dBm dBm conditions Min. typ. Max. units [1] square wave input waveform is recommended below 400 MHz for best phase noise performance. if sine wave input waveform is used below 400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance. [2] For n = 1, frequencies > 8 GHz, and input power > 0 dBm, output power will saturate and gradually drop with increasing input power, but part will continue to function. 4-1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-1 Input Sensitivity vs. Temperature 15 10 Output Power vs. Temperature, Pin = 0 dBm 8 6 4 Frequency DiviDers & Detectors - sMt 4-2 INPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 18 20 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C OUTPUT POWER (dBm) 4 2 0 -2 -4 -6 -8 -10 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 +25C +85C -40C INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 -125 Phase Noise vs. Temperature, Pin = 0 dBm, Fin = 6 GHz -120 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) -130 -135 -140 -145 -150 -155 -160 1.0e+2 100MHz SQ 100MHz SINE 6 GHz 15 GHz -130 +25C +85C -40C -140 -150 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -160 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm T = 25 °C 10 0 Reverse Leakage, Pin = 0 dBm T = 25 °C 0 OUTPUT LEVEL (dBm) -20 -30 -40 -50 -60 -70 Pfeedthru 3rd Harmonic POWER LEVEL (dBm) -10 -10 -20 -30 Both Output Ports Terminated One Output Port Terminated -40 0 2 4 6 8 10 12 14 16 18 20 -50 INPUT FREQUENCY (GHz) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-2 4 Frequency DiviDers & Detectors - sMt Input Sensitivity vs. Temperature 15 10 INPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 18 20 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C Output Power vs. Temperature, Pin = 0 dBm 8 6 OUTPUT POWER (dBm) 4 2 0 -2 -4 -6 -8 -10 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 +25C +85C -40C INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 SSB PHASE NOISE (dBc/Hz) -130 SSB PHASE NOISE (dBc/Hz) 100MHz SQ 100MHz SINE 6 GHz 15 GHz -130 +25C +85C -40C -140 -140 -150 -160 -150 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -160 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm T = 25 °C 10 0 Reverse Leakage, Pin = 0 dBm T = 25 °C 0 -10 -20 POWER LEVEL (dBm) -30 -40 -50 -60 -70 -80 -90 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) -10 -20 -30 -40 -50 -60 -70 Pfeedthru 3rd Harmonic 0 2 4 6 8 10 12 14 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) 4-3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-4 Input Sensitivity vs. Temperature 15 10 Output Power vs. Temperature, Pin = 0 dBm 8 6 4 Frequency DiviDers & Detectors - sMt 4-4 INPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 16 18 20 INPUT FREQUENCY (GHz) Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C OUTPUT POWER (dBm) 4 2 0 -2 -4 -6 -8 -10 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 +25C +85C -40C INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 SSB PHASE NOISE (dBc/Hz) -130 SSB PHASE NOISE (dBc/Hz) 100MHz SQ 100MHz SINE 6 GHz 15 GHz -130 +25C +85C -40C -140 -140 -150 -160 -150 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -160 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm T = 25 °C 10 0 Reverse Leakage, Pin = 0 dBm T = 25 °C 0 -10 -20 POWER LEVEL (dBm) -30 -40 -50 -60 -70 -80 -90 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) -10 -20 -30 -40 -50 -60 -70 Pfeedthru 3rd Harmonic 0 2 4 6 8 10 12 14 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Divide-by-8 4 Frequency DiviDers & Detectors - sMt Input Sensitivity vs. Temperature 15 10 INPUT POWER (dBm) 5 0 -5 -10 -15 -20 -25 0 2 4 6 8 10 12 14 INPUT FREQUENCY (GHz) 16 18 20 Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C Output Power vs. Temperature, Pin = 0 dBm 8 6 OUTPUT POWER (dBm) 4 2 0 -2 -4 -6 -8 -10 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 +25C +85C -40C INPUT FREQUENCY (GHz) Phase Noise vs. Frequency, Pin = 0 dBm -120 100MHz SQ 100MHz SINE 6 GHz 15 GHz Phase Noise vs. Temperature Pin = 0 dBm, Fin = 6 GHz -120 SSB PHASE NOISE (dBc/Hz) -130 SSB PHASE NOISE (dBc/Hz) -130 +25C +85C -40C -140 -140 -150 -160 -150 -170 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 -160 1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) Output Harmonics, Pin = 0 dBm T = 25 °C 10 0 Reverse Leakage, Pin = 0 dBm T = 25 °C 0 -10 -20 POWER LEVEL (dBm) -30 -40 -50 -60 -70 -80 -90 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) -10 -20 -30 -40 -50 -60 -70 Pfeedthru 3rd Harmonic 0 2 4 6 8 10 12 14 16 18 20 -100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) 4-5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Icc vs. Vcc 200 Programming Truth Table for Frequency Division Ratios s0 0 s1 0 0 1 1 s2 0 0 0 1 Divider ratio (n) 1 2 4 Frequency DiviDers & Detectors - sMt 4-6 OPERATING CURRENT (mA) 150 1 1 4 8 100 1 50 N=1 N=2 N=4 N=8 0 = Logic Low 1 = Logic High note: vcc1, vcc2 must be applied before logic. Digital Control Input Voltages 5.1 5.2 5.3 0 4.7 4.8 4.9 5 state Low High s0, s1, s2 0 to 0.4v 3v to 5v Vcc (V) Absolute Maximum Ratings rF input Power supply voltage (vcc) Logic inputs (s0, s1, s2) storage temperature esD sensitivity (HBM) 13 dBm 5.5v -0.5v to (0.5v + vcc) -65 to +125 °c class 1A Reliability Information Junction temperature to Maintain 1 Million Hour MttF nominal Junction temperature (t = 85 °c) thermal resistance (Junction to GnD Paddle, 5v supply) operating temperature 150 °c 112 °c 33 °c/W -40 to +85 °c eLectrostAtic sensitive Device oBserve HAnDLinG PrecAutions F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Outline Drawing 4 Frequency DiviDers & Detectors - sMt notes: 1. LeADFrAMe MAteriAL: coPPer ALLoy 2. DiMensions Are in incHes [MiLLiMeters]. 3. LeAD sPAcinG toLerAnce is non-cuMuLAtive 4. PAD Burr LenGtH sHALL Be 0.15mm MAXiMuM. PAD Burr HeiGHt sHALL Be 0.05mm MAXiMuM. 5. PAcKAGe WArP sHALL not eXceeD 0.05mm. 6. ALL GrounD LeADs AnD GrounD PADDLe Must Be soLDereD to PcB rF GrounD. 7. reFer to Hittite APPLicAtion note For suGGesteD PcB LAnD PAttern. Package Information Part number HMc862LP3e Package Body Material roHs-compliant Low stress injection Molded Plastic Lead Finish 100% matte sn MsL rating MsL1 [2] Package Marking [1] 862 XXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °c 4-7 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Pin Description Pin number 1, 4, 8, 9, 12, 14, 15 Function GnD Description Ground: Backside of package has exposed metal ground slug which must be connected to rF/Dc ground. interface schematic 4 Frequency DiviDers & Detectors - sMt 4-8 2 in rF input must be Dc blocked. 3 nin rF input 180° out of phase with pin 2 for differential operation. Ac ground for single ended operation. Dc block for differential operation. 5, 6, 7 s0, s1, s2 cMos compatible division ratio control bit. see Programming truth table 10 nout Divider output 180° out of phase with pin 11. rF output must be Dc blocked. 11 out Divided output. rF output must be Dc blocked. 13, 16 vcc1, vcc2 supply voltage 5v. connect both pins to +5v supply. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Evaluation PCB 4 Frequency DiviDers & Detectors - sMt List of Materials for Evaluation PCB 119351 item J1 - J3 J4 c1 - c4 c5, c6 c7, c8 r1 - r3 vcc1, vcc2 u1 PcB [2] Description PcB Mount sMA-F rF connector Dc connector Header, Molex 2mm Atc530L, 100 nF, 16v, Broadband capacitor, 0402 Pkg. 1000 pF capacitor, 0402 Pkg. 4.7 µF capacitor, tantalum, 1206 Pkg. 10 kohm resistor, 0402 Pkg. Mill-Max 0.040" Dia. Pc Pin, 3101-2-00-21-00-00-08-0 HMc862LP3e, Programmable Divider 119349 evaluation Board [1] the circuit board used in the application should use rF circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. the evaluation circuit board shown is available from Hittite upon request. [1] reference this number when ordering complete evaluation PcB [2] circuit Board Material: rogers 4350 or Arlon 25Fr 4-9 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC862LP3E v03.1210 0.1 - 15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2, 4, 8) Evaluation PCB Schematic 4 Frequency DiviDers & Detectors - sMt F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 4 - 10