HI-3182PSX-N

HI-3182PSx-N, HI-3185PSx-N August 2006 ARINC 429 DIFFERENTIAL LINE DRIVER PIN CONFIGURATION VREF 1 N/C (See Note * ) 2 SYNC 3 DATA (A) 4 14 V1 13 CLOCK 12 DATA (B) 11 CB 10 BOUT 9 +V 8 GND GENERAL DESCRIPTION The HI-3182, and HI-3185 bus interface products are silicon gate CMOS devices designed as a line driver in accordance with the ARINC 429 bus specifications. In addition to being functional upgrades of Holt's HI-8382 product, they are also alternate sources for a variety of similar line driver products from other manufacturers. Inputs are provided for clocking and synchronization. These signals are AND'd with the DATA inputs to enhance system performance and allow the HI-318X series of products to be used in a variety of applications. Both logic and synchronization inputs feature built-in 2,000V minimum ESD input protection as well as TTL and CMOS compatibility. The differential outputs of the HI-318X series of products are programmable to either the high speed or low speed ARINC 429 output rise and fall time specifications through the use of two external capacitors. The output voltage swing is also adjustable by the application of an external voltage to the VREF input. A 37.5 ohm resistor is in series with each ARINC output. In addition the HI-3182 product also has a fuse in series with each output. The HI-318X series of line drivers are intended for use where logic signals must be converted to ARINC 429 levels such as when using an ASIC, the HI-8584/HI-3282/HI-8282A ARINC 429 Serial Transmitter/Dual Receiver, the HI-6010 ARINC 429 Transmitter/Receiver or the HI-8783 ARINC Interface Device. Holt products are readily available for both industrial and military applications. Please contact the Holt Sales Department for additional information. (Top View) CA 5 AOUT 6 -V 7 HI-3185PSx-N 14 - PIN PLASTIC SMALL OUTLINE (SOIC) NB Note: * Pin 2 is internally not connected (See Page 5 for HI-3182PSx-N package pin configurations) FUNCTION + _ ARINC 429 DIFFERENTIAL LINE DRIVER FEATURES ! Low power CMOS ! TTL and CMOS compatible inputs ! Programmable output voltage swing ! Adjustable ARINC rise and fall times ! Operates at data rates up to 100 Kbits ! Overvoltage protection ! Industrial and Military temperature ranges TRUTH TABLE SYNC CLOCK DATA(A) DATA(B) AOUT X L H H H H L X H H H H X X L L H H X X L H L H 0V 0V 0V -VREF +VREF 0V BOUT COMMENTS 0V 0V 0V +VREF -VREF 0V NULL NULL NULL LOW HIGH NULL (DS3182N Rev. A ) HOLT INTEGRATED CIRCUITS www.holtic.com 08/06 HI-3182PSx-N, HI-3185PSx-N FUNCTIONAL DESCRIPTION The SYNC and CLOCK inputs establish data synchronization utilizing two AND gates, one for each data input (figure 2). Each logic input is TTL/CMOS compatible. Figure 1 illustrates a typical ARINC 429 bus application. Three power supplies are necessary to operate the HI-318X; typically +15V, -15V and +5V. The chip also works with ±12V supplies. The +5V supply can also provide a reference voltage that determines the output voltage swing. The differential output voltage swing will equal 2VREF. If a value of VREF other than +5V is needed, a separate +5V power supply is required for pin V1. With the DATA (A) input at a logic high and DATA (B) input at a logic low, AOUT will switch to the +VREF rail and BOUT will switch to the -VREF rail (ARINC HIGH state). With both data input signals at a logic low state, the outputs will both switch to 0V (ARINC NULL state). The driver output impedance, ROUT, is nominally 75 ohms. The rise and fall times of the outputs can be calibrated through the selection of two external capacitor values that are connected to the CA and CB input pins. Typical values for high-speed operation (100KBPS) are CA = CB = 75pF and for low-speed operation (12.5 to 14KBPS) CA = CB = 500pF. The CA and CB pins swing between +5V and ground allowing the switching of capacitor values with an external singlesupply analog switch. The ARINC outputs of the HI-3182, are protected by internal fuses capable of sinking between 800 - 900 mA for short periods of time (125ms). The Vref pin has an internal pull-up resistor to V+, allowing the use of a simple external zener diode to set the reference voltage. POWER SUPPLY SEQUENCING The power supplies should be controlled to prevent large currents during supply turn-on and turn-off. The recommended sequence is +V followed by V1, always ensuring that +V is the most positive supply. The -V supply is not critical and can be asserted at any time. +5V +15V VREF DATA (A) V1 SYNC CLOCK AOUT +V -V INPUTS DATA (B) CA CB GND TO ARINC BUS BOUT -15V Figure 1. ARINC 429 BUS APPLICATION VREF +V CA A OUT DATA (A) LEVEL SHIFTER AND SLOPE CONTROL (A) CLOCK 24.5 W OUTPUT DRIVER (A) CL SYNC LEVEL SHIFTER AND SLOPE CONTROL (B) 24.5 W OUTPUT DRIVER (B) 13 W RL 13 W FA FB DATA (B) V1 CURRENT REGULATOR Shorted on HI-3185PSx-N GND -V CB B OUT Figure 2. FUNCTIONAL BLOCK DIAGRAM HOLT INTEGRATED CIRCUITS 2 HI-3182PSx-N, HI-3185PSx-N PIN DESCRIPTIONS SYMBOL VREF SYNC DATA (A) CA AOUT -V GND +V BOUT CB DATA (B) CLOCK V1 FUNCTION ANALOG INPUT INPUT INPUT OUTPUT POWER POWER POWER OUTPUT INPUT INPUT INPUT POWER Synchronizes data inputs Data input terminal A DESCRIPTION Ref. voltage used to determine output voltage swing. Pin sources current to allow use of a zener reference. Connection for DATA (A) slew-rate capacitor ARINC output terminal A -12V to -15V 0.0V +12V to +15V ARINC output terminal B Connection for DATA (B) slew-rate capacitor Data input terminal B Synchronizes data inputs +5V ±5% ABSOLUTE MAXIMUM RATINGS All Voltages referenced to GND, TA = Operating Temperature Range (unless otherwise specified) PARAMETER Differential Voltage Supply Voltage SYMBOL VDIF +V -V V1 VREF VIN CONDITIONS Voltage between +V and -V terminals OPERATING RANGE MAXIMUM 40 UNIT V V V V V V V V +10.8 to +16.5 -10.8 to -16.5 +5 ±5% For ARINC 429 For Applications other than ARINC +5 ±5% 1.5 to 6 +7 6 6 > GND -0.3 < V1 +0.3 Voltage Reference Input Voltage Range Output Short-Circuit Duration Output Overvoltage Protection Operating Temperature Range Storage Temperature Range Lead Temperature Junction Temperature See Note: 1 See Note: 2 TA TSTG High-temp & Military Industrial Ceramic & Plastic Soldering, 10 seconds TJ -55 to +125 -40 to +85 -65 to +150 +275 +175 °C °C °C °C °C Note 1. Heatsinking may be required for continuous Output Short Circuit at +125°C and for 100KBPS at +125°C. Note 2. The fuses used for Output Overvoltage Protection may be blown by the presence of a voltage at either output that is greater than ±12.0V with respect to GND. (HI-3182 only) NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. HOLT INTEGRATED CIRCUITS 3 HI-3182PSx-N, HI-3185PSx-N DC ELECTRICAL CHARACTERISTICS +V = +15V, -V = -15V, V1 = VREF = +5.0V, TA = Operating Temperature Range (unless otherwise specified). PARAMETER Supply Current +V (Operating) Supply Current -V (Operating) Supply Current V1 (Operating) Reference Pin Current VREF (Operating) Supply Current +V (During Short Circuit Test) Supply Current -V (During Short Circuit Test) Output Short Circuit Current (Output High) Output Short Circuit Current (Output Low) Input Current (Input High) Input Current (Input Low) Input Voltage High Input Voltage Low Output Voltage High (Output to Ground) Output Voltage Low (Output to Ground) Output Voltage Null Input Capacitance SYMBOL ICCOP (+V) ICCOP (-V) ICCOP (V1) ICCOP (VREF) ISC (+V) ISC (-V) IOHSC IOLSC IIH IIL VIH VIL VOH VOL VNULL CIN No Load No Load No Load CONDITION (0 - 100KBPS) (0 - 100KBPS) (0 - 100KBPS) MIN -16 TYP MAX UNITS +16 500 mA mA µA mA mA mA -80 mA mA 1.0 µA µA V 0.5 V V V mV pF +VREF +.25 -VREF +.25 +250 No Load, VREF = 5V (0 - 100KBPS) Short to Ground Short to Ground Short to Ground Short to Ground (See Note: 1) (See Note: 1) -1.0 -150 +80 -1.0 2.0 -0.4 -0.15 150 VMIN=0 (See Note: 2) VMIN=0 (See Note: 2) No Load No Load No Load See Note 1 (0 -100KBPS) (0 -100KBPS) (0-100KBPS) +VREF -.25 -VREF -.25 -250 15 Note 1. Not tested, but characterized at initial device design and after major process and/or design change which affects this parameter. Note 2. Interchangeability of force and sense is acceptable. AC ELECTRICAL CHARACTERISTICS +V = +15V, -V = -15V, V1 = VREF = +5.0V, TA = Operating Temperature Range (unless otherwise specified). PARAMETER Rise Time ( A OUT , B OUT ) Fall Time ( A OUT , B OUT ) Propagtion Delay Input to Output Propagtion Delay Input to Output SYMBOL tR tF t PLH t PHL CONDITION C A = C B = 75pF C A = C B = 75pF C A = C B = 75pF C A = C B = 75pF See Figure 3. See Figure 3. See Figure 3. See Figure 3. MIN 1.0 1.0 TYP MAX UNITS 2.0 2.0 3.0 3.0 µs µs µs µs DATA (A) 0V DATA (B) 0V VREF 50% 50% ADJUST BY CA 2.0V 0.5V 2.0V 0.5V +4.75V to +5.25V AOUT 0V ADJUST BY CA -VREF 50% 50% -4.75V to -5.25V ADJUST BY CB ADJUST BY CB t PHL +VREF +4.75V to +5.25V -4.75V to -5.25V HIGH NULL BOUT 0V -VREF t PLH tR DIFFERENTIAL OUTPUT 0V 2VREF +9.5V to +10.5V (AOUT - BOUT) NOTE: OUTPUTS UNLOADED tF -2VREF LOW -9.5V to -10.5V Figure 3. SWITCHING WAVEFORMS HOLT INTEGRATED CIRCUITS 4 HI-3182PSx-N, HI-3185PSx-N ADDITIONAL PIN CONFIGURATIONS (See page 1 for 14-Pin Small Outline SOIC) HI-3182PSx-N VREF - 1 GND (See Note * ) - 2 SYNC - 3 DATA(A) - 4 CA - 5 AOUT - 6 -V - 7 GND - 8 16 - V1 15 - N/C 14 - CLOCK 13 - DATA(B) 12 - CB 11 - BOUT 10 - N/C 9 - +V Notes: * Pin 2 may be left floating 16 - PIN PLASTIC SMALL OUTLINE (SOIC) ORDERING INFORMATION HI - 318xPS x x - N PART NUMBER LEAD FINISH Blank F PART NUMBER Tin / Lead (Sn / Pb) Solder 100% Matte Tin (Pb-free, RoHS compliant) TEMPERATURE RANGE FLOW BURN IN I T PART NUMBER 3182PS 3185PS Legend: NB WB -40°C TO +85°C -55°C TO +125°C PACKAGE DESCRIPTION I T NO NO OUTPUT SERIES RESISTANCE FUSE 16 PIN PLASTIC SMALL OUTLINE - WB (SOIC) 14 PIN PLASTIC SMALL OUTLINE - NB (SOIC) - Narrow Body - Wide Body 37.5 Ohms 37.5 Ohms Yes No HOLT INTEGRATED CIRCUITS 5 HI-318xPSx-N PACKAGE DIMENSIONS inches (millimeters) HI-3182PSx-N 16-PIN PLASTIC SMALL OUTLINE (SOIC) - WB (Wide Body) .405 ± .008 (10.287 ± .203) .0105 ± .0015 (.2667 ± .0381) Package Type: 16HW .4065 ± .0125 (10.325 ± .318) Top View .295 ± .004 (7.493 ± .102) Detail A .090 ± .010 (2.286 ± .254) 0° to 8° .050 ± .010 (1.270 ± .254) .0165 ± .0035 (.4191 ± .0889) .033 ± .017 (.838 ± .432) .0025 ± .0015 (.0635 ± .0381) Detail A HI-3185PSx-N 14-PIN PLASTIC SMALL OUTLINE (SOIC) - NB (Narrow Body) .3406 ± .0039 (8.651 ± .099) .00865 ± .00115 (.220 ± .029) Package Type: 14H 14HN .236 ± .008 (6.00 ± .20) Top View .1535 ± .0035 (3.899 ± .089) .0165 ± .0035 (.419 ± ..089) Detail A .061 ± .007 (1.549 ± .178) 0° to 8 ° .050 ± .010 (1.270 ± .254) .033 ± .017 (.838 ± .432) Detail A .0069 ± .0029 (.175 ± .074) HOLT INTEGRATED CIRCUITS 6