MICRO SWITCH Cable-Pull Safety Switches
CPS Series
004785
Issue 3
Datasheet
FEATURES
DESCRIPTION
Honeywell’s MICRO SWITCH CPS Series Cable-Pull Safety
Switches provide a readily accessible emergency stop signal, a
cost-effective means compared to using multiple emergency
stop push-buttons. The CPS Series Cable Pull Safety Switch’s
internal mechanism latches on both slackened cable (push)
and pulled cable.
The 1CPS is intended for use in applications where the cable
span is 76 m [250 ft] or shorter. It is an economical solution for
shorter runs or zone protection typical to automated systems.
The 2CPS Series is intended for use in very long cable runs of
152 m [500 ft] or shorter, such as long conveyor lines found in
warehouses.
A line in the midpoint of the cable tension window indicates
proper cable tension, providing easy set-up. The direct opening
switch contacts are held closed when the actuating cable is
under proper tension and the reset knob is set to the RUN
position. When the actuating cable is pulled, slackened, or
broken, a cam positively opens the NC (Normally Closed)
switch contacts. The snap-action operation causes the switch
contacts to change state and mechanically latch almost
simultaneously when the cable is pulled, slackened, or broken.
The NC switch contacts remain open until the CPS is reset by
properly tensioning the cable and manually rotating the reset
knob.
When the direct opening switch contacts open, the auxiliary
contacts also actuate (open contacts close). The auxiliary
contacts are electrically isolated from the direct-opening
switch contacts. These NO (Normally Open) contacts may be
used for monitoring or signaling.
DIFFERENTIATION
• Internal mechanism latches on both slackened cable (push)
and pulled cable
Safety and Productivity Solutions
• Direct opening action of NC (Normally Closed) contacts
• 2CPS: 2NO/2NC, 1NO/3NC, or 4NC contact configurations
• 1CPS: 1NO/1NC, 2NO/2NC, 1NO/3NC, or 4NC contact
configurations
• Typical cable span of 76 m [250 ft] in an environment with
a temperature change of ±17 °C [±30 °F]. Longer spans
are possible depending upon temperature change and
installation
• Choice of three actuator configurations (2CPS)
• Removable contact block version available (2CPS)
• J-hook turnbuckle included (2CPS)
• Large wiring cavity with straight-through wiring
• Models avaliable without broken cable, slack-cable detection
• 24 Vdc or 120 Vac bright, multi-cluster high-intensity LED
status indicator light available on 2CPS. Single LED on 1CPS
• Gold-plated contacts are standard on 2CPS, available on
1CPS
• Electrostatic, epoxy-coated, die-cast zinc housing
• Optional hardware packets available
POTENTIAL INDUSTRIAL APPLICATIONS
• Long conveyor systems found in warehouses and
distribution centers
• Conveyor systems with a high amount of vibration
• Conveyor systems that experience wide temperature swings
• Long conveyor systems where easy-through wiring, or highly
visible trip status, is required
• Perimeter guarding in hose-down conditions
• Packaging equipment
• Assembly lines
VALUE TO CUSTOMERS
• Cost-effective means of providing an emergency stop signal
compared to multiple emergency stop push buttons
• Capability enhances productivity by minimizing nuisance
stops due to variations in temperature, stretch of cable over
time, or other application variables
• Direct opening of normally closed contacts when cable is
actuated
PORTFOLIO
The CPS Series is the largest switch in Honeywell’s MICRO
SWITCH line of safety switches. For more details on the
extensive line of Honeywell safety switches, click here.
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Table 1. Specifications
Characteristic
Parameter
Description
cable-pull safety switches
Switching options
1NO/1NC direct acting
2NO/2NC direct acting
1NO/3NC direct acting
4NC direct acting
Sealing
IP67, NEMA 1, 4, 12, 13
Contacts
silver, gold plated over silver
Conduit/Connectors
1/2 NPT, PG 13.5, 20 mm, PF 1/2; Brad Harrison 10-pin conductor
Force to maintain actuation shaft
2CPS: 25 lb*
Actuation shaft operating force
2CPS: 40 lb*
Operating temperature
-40 °C to 80 °C [-40 °F to 176 °F]
Storage temperature
1CPS: -40 °C to 85 °C [-40 °F to 185 °F]
Mechanical endurance
1 million operations
Rated thermal current (Ith)
10 A
Rated impulse withstand (Uimp)
2500 V
Rated insulation voltage (Ui)
300 V
Useable gold-plated current
1 mA to 50 mA, 60 Vdc max./125 Vdc max.
Pollution degree
3
Conditional short circuit current
1000 A
Short circuit protective device
(type/maximum rating)
Class J fuse (10 A/600 V)
Shock
15 g per IEC 68-2-27
Vibration
10 Hz to 500 Hz, 5 g per IEC 68-2-6
Approvals
UL, CSA, CE, SIL
Standards
• UL Listed per File E37138 against UL508
• CSA Certified per File 57323 against CSA C22.2 No. 14
• CE mark: The CPS complies with Low Voltage Directive 2006/95/EC; Machinery Directive
2006/42/EC only as the directives relate to the components being used in a safety function; EN
60947-1; EN 60947-5-1; EN 60947-5-5
• SIL: MCTF (Mechanical Life): >1,000,000 cycles with single-sided confidence limit of 100 %.
MCTF (Electrical Life): >25,000 cycles with single-sided confidence limit of 87.5 %.
Highest SIL Capability: SIL3 (HFT:1), IEC 61508-2: 2010. Proof Test Interval: 1 Year
* Incline measures, and not typical for manual trip
Table 2. Electrical Ratings
ac
dc
A300
Ue
AC15
Ie
Q300
Ue
DC13
Ie
Volts
Amps
Volts
Amps
–
–
24
2.8
120
6
125
0.55
240
3
250
0.27
Ith = 10 A
2 sensing.honeywell.com
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Figure 1. 1CPS Product Nomenclature and Order Guide
1CPS
Switch Type
1CPS Series
Single-Head
Cable-Pull
Safety Switch
A
1
A
-N
Conduit
Basic Switch
Code
Indicator-Pilot
Light Code
Without
Broken
Cable
Detection
1NO/1NC direct acting
Switch 1: 1NO/1NC
Switch 2: None
A
1/2 NPT
1
B
PG 13.5
2
C
20 mm
3
2NO/2NC direct acting
Switch 1: 1NO/1NC
Switch 2: 1NO/1NC
1NO/3NC direct acting
Switch 1: 1NO/1NC
Switch 2: 2NC
D
PF 1/2
4
4NC direct acting
Switch 1: 2NC
Switch 2: 2NC
5
6
7
8
1NO/1NC direct acting, gold contacts
Switch 1: 1NO/1NC
Switch 2: None
2NO/2NC direct acting, gold contacts
Switch 1: 1NO/1NC
Switch 2: 1NO/1NC
1NO/3NC direct acting, gold contacts
Switch 1: 1NO/1NC
Switch 2: 2NC
A
24 Vdc LED
B
120 Vac LED
4NC direct acting, gold contacts
Switch 1: 2NC
Switch 2: 2NC
NOTE: Not all combinations of model code are available.
Please contact your Honeywell provider/representative for assistance.
Figure 2. 2CPS Product Nomenclature and Order Guide
2CPS
A
1
A
1
A
Conduit
Contact
Mounting Code
Basic Switch
Code
Actuation
Code
Indicator-Pilot
Light Code
A
1/2 NPT
1
Standard: contact
block mounted
to housing
A
2NO/2NC, direct acting
Switch 1: 1NO/1NC
Switch 2: 1NO/1NC
1
Maintained,
both sides
A
24 Vdc LED
cluster
B
PG 13.5
2
Removeable:
contact blocks
with receptacles
B
1NO/3NC, direct acting
Switch 1: 1NO/1NC
Switch 2: 2NC
2
Maintained, left side
No actuation, right side
B
120 Vac LED
cluster
C
20 mm
D
4NC, direct acting
Switch 1: 2NC
Switch 2: 2NC
3
Maintained, right side
No actuation, left side
D
PF 1/2
4
Maintained, both sides
w/o broken cable detection
5
Maintained, left side
No actuation, right side
w/o broken cable detection
61
Maintained, right side
No actuation, left side
w/o broken cable detection
Switch Type
2CPS Series
Dual-Head
Cable-Pull
Safety Switch
NOTE: Not all combinations of model code are available.
Please contact your Honeywell provider/representative for assistance.
1
Not valid on 4NC switches
Safety and Productivity Solutions
3
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
TEMPERATURE-SPAN DISTANCE APPLICATION
INFORMATION
Cable-pull switches featuring broken cable detection require
pre-tensioning in order to enable the RUN condition.
The relative expansion or contraction of the steel actuating
cable when the ambient temperature increases or decreases
must be taken into account when pre-tensioning a cable pull
switch.
Table 3. Circuitry Charts
Circuitry
Chart
1NO/1NC
2NO/2NC
The change in cable length with change in temperature can
cause significant nuisance shut downs on longer runs.
Install the system when the temperature is at the mid point of
the extremes. If a warehouse has a low temperature of 15.6 °C
[60 °F]and a high of 32.2 °C [90 °F], set up the system at the
midpoint 23.9 °C [75 °F].
1NO/3NC
Use an endspring or another CPS at the opposite end of the
cable span to double the temperature tolerance and to meet
the requirements of EN 418.
4NC
Figure 3. Total Temperature Variation vs. Cable Span
Distance
1NO/1NC
1NO/3NC
2NO/2NC
4NC
Table 4. 1CPS Contact Blocks
= grounding screw
4 sensing.honeywell.com
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Table 5. 2CPS Contact Blocks
Removable Contact Blocks with
Heavy-Duty Wiring Receptacles
Contact Block Mounted to Housing
A = grounding screw
A = grounding screw
2NO/2NC
2NO/2NC
1NO/3NC
1NO/3NC
4NC
Safety and Productivity Solutions
5
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Conduit
Switching
Bar Chart
¢ Contact Closed | ¨ Contact Open
Contact
Material
1CPSA1
1/2 in NPT 1NO/1NC
silver alloy
1CPSA1A
1/2 in NPT 1NO/1NC
silver alloy
1CPSA1B
1/2 in NPT 1NO/1NC
1CPSA5
1/2 in NPT 1NO/1NC
1CPSC1
20 mm
1NO/1NC
1CPSC1A
20 mm
1NO/1NC
1CPSC5
20 mm
1NO/1NC
1CPSA2
1/2 in NPT 2NO/2NC
silver alloy
1CPSA2A
1/2 in NPT 2NO/2NC
silver alloy
1CPSA2B
1/2 in NPT 2NO/2NC
1CPSA6
1/2 in NPT 2NO/2NC
1CPSA6A
1/2 in NPT 2NO/2NC
1CPSA6B
1/2 in NPT 2NO/2NC
1CPSC2
20 mm
2NO/2NC
12,7
[0.5]
Left 21-22
Switch 13-14
9,9
[0.39]
9,9
[0.39]
7,9
3,8
3,8
7,9
12,7
[0.31] [0.15] [0.15] [0.31]
[0.5]
0
Slackened
cable
–
ü
gold-plated
Pulled
cable
silver alloy
–
–
ü
gold-plated
Left
Switch
Right
Switch
12,7
[0.5]
21-22
13-14
21-22
13-14
9,9
[0.39]
0
7,9
3,8
3,8
7,9
[0.31] [0.15] [0.15] [0.31]
9,9
[0.39]
Pulled
cable
silver alloy
1CPSC2B
20 mm
2NO/2NC
silver alloy
1CPSC6
20 mm
2NO/2NC
gold-plated
1CPSC6A
20 mm
2NO/2NC
gold-plated
1CPSA3
1/2 in NPT 1NO/3NC
silver alloy
1CPSA3A
1/2 in NPT 1NO/3NC
silver alloy
1/2 in NPT 1NO/3NC
0
7,9
3,8
3,8
7,9
[0.31] [0.15] [0.15] [0.31]
9,9
[0.39]
–
–
–
ü
ü
silver alloy
Proper
cable
tension
2NO/2NC
9,9
[0.39]
–
ü
gold-plated
20 mm
12,7
[0.5]
21-22
13-14
11-12
21-22
–
ü
gold-plated
gold-plated
Slackened
cable
Left
Switch
Right
Switch
–
silver alloy
12,7
[0.5]
–
–
silver alloy
Proper
cable
tension
Notes
–
ü
silver alloy
1CPSC2A
1CPSA3A-F01
Pilot Light
120 Vac LED
Catalog
Listing
Pilot Light
24 Vdc LED
Table 6. 1CPS With Broken Cable Detection Order Guide
–
–
–
ü
ü
–
–
–
ü
–
ü
–
silver alloy
ü
10-pin Brad
Harrison connector; actuator
to right
silver alloy
ü
10-pin Brad
Harrison connector; actuator
to left
12,7
[0.5]
1CPSA3A-F02
1/2 in NPT 1NO/3NC
1CPSA3B
1/2 in NPT 1NO/3NC
1CPSA7
1/2 in NPT 1NO/3NC
gold-plated
–
1CPSC3
20 mm
1NO/3NC
silver alloy
–
1CPSC3A
20 mm
1NO/3NC
silver alloy
1CPSC7
20 mm
1NO/3NC
gold-plated
–
1CPSA4
1/2 in NPT 4NC
silver alloy
–
1CPSA4B
1/2 in NPT 4NC
1CPSA8
1/2 in NPT 4NC
1CPSC4
20 mm
1CPSC8
20 mm
6 sensing.honeywell.com
4NC
4NC
Slackened
cable
Left
Switch
Right
Switch
12,7
[0.5]
11-12
21-22
11-12
21-22
9,9
[0.39]
Proper
cable
tension
0
9,9
[0.39]
7,9
3,8
3,8
7,9
[0.31] [0.15] [0.15] [0.31]
Slackened
cable
Proper
cable
tension
silver alloy
Pulled
cable
Pulled
cable
12,7
[0.5]
silver alloy
ü
–
–
ü
ü
–
gold-plated
–
silver alloy
–
gold-plated
–
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
1CPSA1-N
Conduit
Switching
Bar Chart
¢ Contact Closed | ¨ Contact Open
1/2 in NPT 1NO/1NC
7,9
[0.31]
0
1CPSA1A-N
1/2 in NPT 1NO/1NC
1CPSA1B-N
1/2 in NPT 1NO/1NC
1CPSA2-N
1/2 in NPT 2NO/2NC
1CPSA2B-N
1/2 in NPT 2NO/2NC
9,9
[0.39]
silver alloy
silver alloy
Pulled
cable
21-22
13-14
21-22
13-14
0
7,9
[0.31]
9,9
[0.39]
Notes
–
12,7
[0.5]
Left 21-22
Switch 13-14
Left
Switch
Right
Switch
Contact
Material
Pilot Light
120 Vac LED
Catalog
Listing
Pilot Light
24 Vdc LED
Table 7. 1CPS Without Broken Cable Detection Order Guide
silver alloy
–
ü
ü
silver alloy
–
–
12,7
[0.5]
silver alloy
ü
–
silver alloy
ü
–
Pulled
cable
9,9
[0.39]
1CPSA4B-N
1/2 in NPT 4NC
Left
Switch
Right
Switch
11-12
21-22
11-12
21-22
0
7,9
[0.31]
12,7
[0.5]
Pulled
cable
Safety and Productivity Solutions
7
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Pilot Light LED
Actuation
Bar Chart
¢ Contact Closed
¨ Contact Open
Removeable
Contact Block
Standard
Contact Block
Switching
Catalog Listing
Conduit
Table 8. 2CPS With Broken Cable Detection and Silver Alloy Contacts Order Guide
Notes
2CPSA1A1
1/2 in NPT 2NO/2NC
ü
Both
2CPSA1A1A
1/2 in NPT 2NO/2NC
ü
Both
24
Vdcdc
2CPSA1A1A-FW 1/2 in NPT 2NO/2NC
ü
Both
10-pin Brad
24 Vdc Harrison
connector
2CPSA1A1B
1/2 in NPT 2NO/2NC
ü
Both
120
Vac
2CPSA1A2
1/2 in NPT 2NO/2NC
ü
Left only
2CPSA1A2A
1/2 in NPT 2NO/2NC
ü
Left only
24 Vdc
2CPSA1A2A-FW 1/2 in NPT 2NO/2NC
ü
Left only
10-pin Brad
24 Vdc Harrison
connector
2CPSA1A2B
1/2 in NPT 2NO/2NC
ü
Left only
120
Vac
2CPSA1A3
1/2 in NPT 2NO/2NC
ü
Right only
2CPSA1A3A
1/2 in NPT 2NO/2NC
ü
Right only 24 Vdc
ü
10-pin Brad
Right only 24 Vdc Harrison
connector
ü
Right only
2CPSA1A3A-FW 1/2 in NPT 2NO/2NC
2CPSA1A3B
1/2 in NPT 2NO/2NC
2CPSA2A1
1/2 in NPT 2NO/2NC
2CPSA2A1A
1/2 in NPT 2NO/2NC
2CPSA2A1B
1/2 in NPT 2NO/2NC
2CPSA2A2
Left
Switch
Right
Switch
12,7
[0.5]
21-22
13-14
21-22
13-14
9,9
[0.39]
0
7,9
3,8
3,8
7,9
[0.31] [0.15] [0.15] [0.31]
9,9
[0.39]
12,7
[0.5]
120
Vac
ü
Both
ü
Both
24 Vdc
ü
Both
120
Vac
1/2 in NPT 2NO/2NC
ü
Left only
2CPSA2A2A
1/2 in NPT 2NO/2NC
ü
Left only
24 Vdc
2CPSA2A2B
1/2 in NPT 2NO/2NC
ü
Left only
120
Vac
2CPSA2A3
1/2 in NPT 2NO/2NC
ü
Right only
2CPSA2A3A
1/2 in NPT 2NO/2NC
ü
Right only 24 Vdc
2CPSA2A3B
1/2 in NPT 2NO/2NC
ü
Right only
2CPSC1A1
20 mm
2NO/2NC
ü
Both
2CPSC1A1A
20 mm
2NO/2NC
ü
Both
2CPSC1A2
20 mm
2NO/2NC
ü
Left only
2CPSC1A2A
20 mm
2NO/2NC
ü
Left only
2CPSC1A3
20 mm
2NO/2NC
ü
Right only
2CPSC1A3A
20 mm
2NO/2NC
ü
2CPSC2A1A
20 mm
2NO/2NC
8 sensing.honeywell.com
Slackened
cable
Proper
cable
tension
Pulled
cable
120
Vac
24 Vdc
24 Vdc
Right only 24 Vdc
ü
Both
24 Vdc
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Pilot Light LED
Actuation
Bar Chart
¢ Contact Closed
¨ Contact Open
Removeable
Contact Block
Standard
Contact Block
Switching
Catalog Listing
Conduit
Table 8. 2CPS With Broken Cable Detection and Silver Alloy Contacts Order Guide, continued
Notes
2CPSA1B1
1/2 in NPT 1NO/3NC
ü
Both
2CPSA1B1A
1/2 in NPT 1NO/3NC
ü
Both
24 Vdc
2CPSA1B1A-F01 1/2 in NPT 1NO/3NC
ü
Both
10-pin Brad
24 Vdc Harrison
connector
2CPSA1B1B
1/2 in NPT 1NO/3NC
ü
Both
120
Vac
2CPSA1B2
1/2 in NPT 1NO/3NC
ü
Left only
120
Vac
2CPSA1B2A
1/2 in NPT 1NO/3NC
ü
Left only
24 Vdc
ü
Left only
10-pin Brad
24 Vdc Harrison
connector
ü
Left only
120
Vac
ü
Right only
ü
Right only 24 Vdc
2CPSA1B3A-F01 1/2 in NPT 1NO/3NC
ü
10-pin Brad
Right only 24 Vdc Harrison
connector
2CPSA1B3B
1/2 in NPT 1NO/3NC
ü
Right only
2CPSA2B1
1/2 in NPT 1NO/3NC
ü
Both
2CPSA2B1A
1/2 in NPT 1NO/3NC
ü
Both
24 Vdc
2CPSA2B1B
1/2 in NPT 1NO/3NC
ü
Both
120
Vac
Both
24 Vdc
2CPSA1B2A-F01 1/2 in NPT 1NO/3NC
2CPSA1B2B
1/2 in NPT 1NO/3NC
2CPSA1B3
1/2 in NPT 1NO/3NC
2CPSA1B3A
1/2 in NPT 1NO/3NC
2CPSC1D1A
20 mm
4NC
Left
Switch
Right
Switch
12,7
[0.5]
21-22
13-14
11-12
21-22
9,9
[0.39]
7,9
3,8
3,8
7,9
[0.31] [0.15] [0.15] [0.31]
Slackened
cable
Left
Switch
Right
Switch
12,7
[0.5]
11-12
21-22
11-12
21-22
0
Proper
cable
tension
9,9
[0.39]
12,7
[0.5]
Pulled
cable
120
Vac
0
9,9
[0.39]
7,9
3,8
3,8
7,9
12,7
[0.31] [0.15] [0.15] [0.31]
[0.5]
9,9
[0.39]
Slackened
cable
ü
Proper
cable
tension
Pulled
cable
Safety and Productivity Solutions
9
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
2CPSA1A4
1/2 in NPT 2NO/2NC
2CPSA1A4B
1/2 in NPT 2NO/2NC
2CPSA1A5B
1/2 in NPT 2NO/2NC
2CPSA1A6B
1/2 in NPT 2NO/2NC
2CPSA2A4A
1/2 in NPT 2NO/2NC
2CPSA2A4B
1/2 in NPT 2NO/2NC
2CPSC1A4-F02
20 mm
10 sensing.honeywell.com
2NO/2NC
Left
Switch
Right
Switch
21-22
13-14
21-22
13-14
0
7,9
[0.31]
9,9
[0.39]
Pulled
cable
12,7
[0.5]
Pilot Light
LED
Actuation
Bar Chart
¢ Contact Closed
¨ Contact Open
Removeable
Contact Block
Standard
Contact Block
Switching
Catalog Listing
Conduit
Table 9. 2CPS Without Broken Cable Detection and With Silver Alloy Contacts Order Guide
ü
Both
ü
Both
120 Vac
ü
Left only
120 Vac
ü
Right only 120 Vac
ü
ü
Both
24 Vdc
ü
Both
120 Vac
Both
Notes
No turnbuckles included
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Figure 4. 1CPS Dimensional Drawing
172,72 mm [6.8 in]
6,6 mm
[0.26 in]
88,9 mm
[3.5 in]
152,4 mm [6.0 in]
Indicator version only
81,28 mm [3.2 in]
33,02 mm
[1.3 in]
12,7 mm
[0.5 in]
99,1 mm 76,2 mm
[3.9 in]
[3.0 in]
53,34 mm
[2.1 in]
4 X Ø 7,37 mm
[4 X Ø 0.29 in]
117,25 mm [4.616 in]
approx. at full travel
56,8 mm
[2.24 in]
65,2 mm
[2.57 in]
50,82 mm
[2.001 in]
3X 25,4 mm
[3X 1.0 in]
25,4 mm
[1.0 in]
3X conduit thread
4X mounting pad
Safety and Productivity Solutions
11
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Figure 5. 2CPS Dimensional Drawing
40,39 mm
[1.59 in]
66,8 mm
[2.63 in]
84,07 mm
[3.31 in]
92,89 mm
[3.66 in]
323,85 mm [12.75 in] approx. at actuation
152,4 mm [6.0 in]
Manual reset button
19,05 mm
[0.75 in]
52,07 mm
[2.05 in]
12,7 mm
[0.5 in]
40,39 mm
[1.59 in]
2X 7,11 mm [0.28 in]
18,29 mm [0.72 in]
34,93 mm [1.375 in]
152,4 mm
[6 in]
2X 7,11 mm
[0.28 in]
2X 9,14 mm [0.36 in]
81,3 mm
[3.2 in]
2X mounting pad
104,78 mm [4.125 in]
Indicator version only
2X 31,75 mm [1.25 in]
12,7 mm [0.5 in]
57,15 mm
[2.25 in]
139,7 mm [5.50 in]
3X conduit thread
2X mounting pad
2X 6,9 mm [0.27 in]
3X 12,46 mm [0.845 in]
12 sensing.honeywell.com
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Figure 6. 1CPS Application Information
Figure 7. 2CPS Application Information
Safety and Productivity Solutions
13
MICRO SWITCH Cable-Pull Safety Switches, CPS Series
Table 10. Accessories/Hardware Packets
Catalog Listing
Accessory
CLSZC1
Cable - 7,6 m [25 ft] length
CLSZC2
Cable - 15,2 m [50 ft] length
CLSZC3
Cable - 30,5 m [100 ft] length
CLSZC4
Cable - 45,7 m [150 ft] length
CLSZC5
Cable - 61 m [200 ft] length
CLSZC7
Cable - 76,2 m [250 ft] length
CLSZTC
(2) Thimbles
(2) Low-profile duplex cable clamps
CLSZ1S
(1) Draw-bar endspring
CPSZ1E
M6 x 1 x 60 mm eyebolt
CPSZ1S
(1) Draw-bar endspring
CPSZK1
(1) J-hook turnbuckle with lock nuts
(2) Thimbles
(2) Low-profile duplex cable clamps
(16) Sets of cable supports [(16) 1/4-20 eye bolts, (32) 1/4-20 nuts, (32) flat washers, (16) lock washers]
CPSZK2
European hardware packet
(1) J-hook turnbuckle with lock nuts
(2) Thimbles
(2) Stainless steel cable clamps
(16) Sets of cable supports [(16) 1/4-20 eye bolts, (32) 1/4-20 nuts, (32) flat washers, (16) lock washers]
CPSZTB
J-hook turnbuckle with lock nuts (included with 2CPS)
CPSLED24
Multi-cluster LED accessory - 24 Vdc (conduit mount)
CPSLED120
Multi-cluster LED accessory - 120 Vac (conduit mount)
CPS-BRACKET
Mounting bracket (to be used with 1CPS or 2CPS)
Figure 8. CPSLED Dimensional Drawing
14 sensing.honeywell.com
Figure 9. CPS-Bracket
m WARNING
ADDITIONAL MATERIALS
The following associated literature is available on the Honeywell
web site at sensing.honeywell.com:
•
•
•
•
•
•
Product line guide
Product part listing/nomenclature tree
Product range guide
CPS troubleshooting guide
Electromechanical safety switch product selection guide
Application note: MICRO SWITCH switches in conveyor
applications
RISK TO LIFE OR PROPERTY
Never use this product for an application involving serious
risk to life or property without ensuring that the system as a
whole has been designed to address the risks, and that this
product is properly rated and installed for the intended use
within the overall system.
Failure to comply with these instructions could result in
death or serious injury.
m WARNING
MISUSE OF DOCUMENTATION
•
•
The information presented in this product sheet is for
reference only. Do not use this document as a product
installation guide.
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
Warranty/Remedy
Find out more
Honeywell serves its customers
through a worldwide network of
sales offices, representatives and
distributors. For application assistance, current specifications,
pricing or name of the nearest
Authorized Distributor, contact
your local sales office.
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty
applies unless agreed to otherwise by Honeywell in writing;
please refer to your order acknowledgement or consult your
local sales office for specific warranty details. If warranted
goods are returned to Honeywell during the period of coverage,
Honeywell will repair or replace, at its option, without charge
those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all
other warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While Honeywell may provide application assistance personally,
through our literature and the Honeywell web site, it is buyer’s
sole responsibility to determine the suitability of the product in
the application.
To learn more about Honeywell’s
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this writing.
products, call +1-815-235-6847
However, Honeywell assumes no responsibility for its use.
or 1-800-537-6945,
visit sensing.honeywell.com, or
e-mail inquiries to
info.sc@honeywell.com
Honeywell Safety and Productivity Solutions
1985 Douglas Drive North
Golden Valley, MN 55422
honeywell.com
004785-3-EN IL50 GLO
September 2016
© 2016 Honeywell International Inc. All rights reserved.