3132-1K

Model 3132 Tension/Compression Pancake Load Cell DESCRIPTION These general purpose designs have exceptional structural Minimum deflection and compactness make these general- capability to withstand extraneous loads, such as torque, purpose load cells easy to install and use. bending moments, and side loads. Available in capacities of 500 lb to 5000 lb, they offer maximum performance and enhanced accuracy. FEATURES • 500 lb to 5000 lb range • Low sensitivity to extraneous loads • Low deflection • Rugged welded construction • Built-in temperature compensation Model 3132 PERFORMANCE SPECIFICATIONS Characteristic Measure Load range 500, 1000, 2000, 3000, 5000 lb Non-linearity ±0.1 % of rated output Hysteresis ±0.1 % of rated output Repeatability ±0.05 % of rated output Output @ rated capacity 3 mV/V ±0.25 % (nominal) Operation Tension/compression Resolution Infinite Standard calibration Tension (+) and compression (-) 1 TYPICAL SYSTEM DIAGRAM Output Amplifier Universal In-Line Amplifiers +/-5 VDC UV +/-10 VDC UV-10 0 +/-5 VDC UBP 4-20mA (3 wire) U3W 4-20mA (2 wire) U2W DIN rail Mount In-Line Amplifiers 0 +/- 5 VDC (3 wire) DV-05 4-20mA (3 wire) DA-05 0 +/- 10 VDC (3 wire) DV10 Measure Temperature, operating -54 °C to 93 °C [-65 °F to 200 °F] Temperature, compensated 21 °C to 77 °C [70 °F to 170 °F] Temperature effect, zero ±0.002 % of rated output/°F Temperature effect, output ±0.002 % of reading/°F ELECTRICAL SPECIFICATIONS Characteristic Measure Strain gage type Foil Excitation (maximum) 20 Vdc or Vac RMS Insulation resistance > 5000 mOhm @ 50 Vdc Bridge resistance (tolerance) 350 ohm Number of bridges 1 or 2 Zero balance ±1.0 % Electrical termination PT02E-10-6P mates with PT06W-10-6S MECHANICAL SPECIFICATIONS Characteristic Measure Static overload capacity 150 % of nominal capacity Material Carbon steel Natural frequency See table WIRING CODES Cable Red (+) excitation Black (-) excitation Green (+) output White (-) output 2 Honeywell • Sensing and Control Power Supply Honeywell ENVIRONMENTAL SPECIFICATIONS Characteristic Customer Supplied Chart Recorder Alarm Panel Data Acquisition Computer PLC In-Line Amplifiers (Used with unamplified units only) In-Line Amplifier Output Input Serial Number Display Units MODEL 3132 SC500 SC2001 GM 7541 SC1000 SC3004 NK 7558 SC2000 HH 7561-PSD 2003.1 lb. L1 L2 L3 L4 OR VALUE CLEAR UP DOWN SETUP CHAN TARE ENTER EXIT Mating Connectors & Cables 023-LW181-023-LF Mating Connector 7205-76-XX* Mating connector & 6 conductor cable (unamplified unit with sense leads but not shunt cal) 7205-75-XX** Mating connector & 4 conductor cable (unamplified unit without sense leads but not shunt cal) 7205-83-XX* Mating connector & 6 conductor cable (for connection to instrument 7541) 7205-82-XX** Mating connector & 4 conductor cable (for connection to instrument 7541) * XX represents length in feet ** XX represents length in feet 100ft maximum 20ft maximum Tension/Compression Pancake Load Cell NATURAL FREQUENCY Nominal load limit capacity Fz Static extraneous load limits lb N Static overShear FX or load capacity FY (lb) (% of nominal capacity) Bending MX or MY (lb-in) Torque MZ (lb-in) Deflection at nominal load limit (in) Ringing frequency (Hz) 500 2K 150 1400 2800 1100 0.005 1600 1K 5K 150 2000 3900 1100 0.005 2000 2K 10K 150 2800 5000 1100 0.005 3200 3K 15K 150 3400 5500 1100 0.005 4100 5K 20K 150 4200 5500 1100 0.005 5000 MOUNTING DIMENSIONS Model A cm [in] B cm [in] C cm [in] D cm [in] E cm [in] F cm [in] 3132 6,65 [2.62] 1,60 [0.63] 8,89 [3.50] 2,54 [1.0] 3,02 [1.19] 4,45 [1.75] G cm [in] H cm [in] J cm [in] K cm [in] L cm [in] 0,64 [0.25] 8,70 [0.34] 5,08 [2.0] 3,33 [1.31] 2,54 [1.0] Honeywell • Sensing and Control 3 Model 3132 Tension/Compression Pancake Load Cell NOTES 1. This unit calibrated to Imperial (non-Metric) units. Warranty. Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. For more information about Sensing and Control products, visit www.honeywell.com/sensing or call +1-815-235-6847 Email inquiries to info.sc@honeywell.com WARNING PERSONAL INJURY • DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARNING MISUSE OF DOCUMENTATION • The information presented in this catalogue is for reference only. DO NOT USE this document as product installation information. • Complete installation, operation and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. Sensing and Control Automation and Control Solutions Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 USA +1-815-235-6847 www.honeywell.com/sensing 008624-1-EN IL50 GLO  May 2008 Copyright © 2008 Honeywell International Inc. All rights reserved.