392551M9725

PART NUMBER 4 2 3 REVISION HISTORY SEE SHEET-2 TABLE .812 MAX [ 20.62 ] D .234 MAX 2 CENTER (C) (3X .088 ) [ 2.24 ] .062 .005 TYP [ 1.57 0.13 ] C .484 .016 [ 12.29 0.41 ] D REV DOCUMENT DESCRIPTION CHG'D BY DATE APPROVED A 0112190 RELEASED BM 2014-08-05 M. MIKE [ # 0.79] A D SHOWN WITH SHAFT AT 50% ROTATION [ # 0.41] .025 MAX [ 0.64 ] 1 2 .515 .016 [ 13.08 0.41 ] [ # 0.25] B # .002 [ # 0.05] 2 ( .080 [ 2.03 ] TYP ) .200 .005 [ 5.08 0.13 ] 3 RIGHT (R) .125 .001 [ 3.18 0.02 ] 1 LEFT (L) .200 .005 [ 5.08 0.13 ] C DATE CODE YY IS LAST 2 DIGITS OF YEAR WW IS WEEK NUMBER 1/4-32 NEF-2A 1 MARKING SURFACE 45 $ MOUNTING SURFACE 2X .025 .015 [ 0.64 0.38 ] B 45 $ 1/2 $ ( 90 $ ) X.012 [ 0.3 ] OUTSIDE OF LOCATING PINS MAY BE FLAT LOCKING WASHER O-RING EPOXY SEALANT SPECIFICATIONS. B TAPER: LINEAR LINEARITY (INDEPENDENT): # 5% TAPER TOLERANCE # 20% OF NOMINAL RESISTANCE AT 50% # 3% MECHANICAL ROTATION. MAX WORKING VOLTAGE: 350 VDC APPLIED ACROSS L & R TERMINALS. POWER NOT TO EXCEED RATING. DIELECTRIC STRENGTH: 750 VAC FOR 60s @ ATM [1 MPa] 350 VAC FOR 60s @ 3.4 IN Hg [11.5 KPa] POWER RATING: 0.5W @ 158 $ F [70 $ C], DE-RATED LINEARLY TO 0@ 248 $ F [120 $ C] CRV 1.5% OF TOTAL RESISTANCE END RESISTANCE: 4 ^ MAX AT EACH END OF ROTATION RESISTANCE AND TOLERANCE: (REFER TO TABLE) ELECTRICAL ROTATION: 295 $ # 5 $ EFFECTIVE ELECTRICAL ROTATION: 265 $ TYPICAL SCALE 2:1 ( ISOMETRIC VIEW - REF ONLY ) SHAFT NICKEL PLATED BRASS HOUSING THERMOPLASTIC NICKEL PLATED BRASS BASE C THERMOSET TERMINALS BRASS, SOLDER (TIN-LEAD) DIP FINISH SEALANT EPOXY LOCK WASHER CW NICKEL PLATED PHOS BRONZE MOUNTING NUT NICKEL PLATED BRASS PANEL O-RING BUNA N UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION L ROTATIONAL LIFE: 50,000 CYCLES STORAGE TEMPERATURE: -67 $ F [-55 $ C] TO 248 $ F [120 $ C] OPERATING TEMPERATURE: -40 $ F [-40 $ C] TO 248 $ F [120 $ C] . ROTATIONAL TORQUE: 0.5 TO 2.0 OZ-IN [3.5 TO 14 mN m] . STOP TORQUE: 3 LB-IN [0.34 N m] MIN MECHANICAL ROTATION: 295 $ # 5 $ 4 MATERIALS BUSHING OPERATIONAL SPECIFICATIONS: A C MOUNTING NUT 3 ELECTRICAL SPECIFICATIONS: 3 R .040 .002 2 [ 1.02 0.05 ] (FROM n .515) 2 PLS LOCATING PIN #2 2 GENERAL SPECIFICATIONS AND NOTES: SERIES: 392 CONDUCTIVE PLASTIC ELEMENT SUPPLIED WITH MOUNTING NUT, LOCKING WASHER AND O-RING. NUT AND WASHER PACKAGED ASSEMBLED OR UNASSEMBLED BASED ON LISTING (REFER TO TABLE ON SHEET2), O-RING IS ASSEMBLED. 1 MARKING INFORMATION SHOWN ON SIDE OF HOUSING. REFER TO TABLE FOR SPECIFIC LISTING MARKING INFORMATION. WEIGHT OF SINGLE CONTROL: .25 OUNCE [6.8 GRAMS] APPROX. VALUES ARE SHOWN IN STANDARD AND METRIC UNITS. METRIC UNITS ARE IN [ ]. IF CONVERSION DIFFERENCE EXISTS, THE STANDARD UNIT PREVAILS. CONTROLS HAVE AN INTERNAL O-RING SHAFT SEAL. UNITS ARE SEALED FOR WAVE SOLDER AND WASH PROCESSING. BUILT IN ACCORDANCE WITH MIL-R-94. 2 DIMENSIONS FOR BODY DIAMETER AND LOCATING PINS DEVIATE FROM MIL-R-94 LOCATING PIN #1 SCHEMATIC R DIMENSIONS ARE IN INCHES DECIMAL TOL NO PLACE 1 PLACE 2 PLACE 3 PLACE ANGULAR TOL MATERIAL MULTI-SHEET DRAWING 3 ----------- # # # # # .400 .030 .010 .005 2 $ [10.16] [0.76] [0.25] [0.13] CHAMFER - TITLE # 5 $ SEE TABLE FINISH APPLICABLE DOCUMENTS: ASME Y14.100-2004 ASME Y14.5-2009 2 COMPUTER GENERATED DRAWING: PRO/ENGINEER SIZE CAGE CODE C - 4:1 SCALE DWG NO 392-MATRIX-IDWG-2 REF WT: SEE NOTE RELEASE DATE 2014-08-05 DRW: B. MOHAPATRA 2014-05-28 RDE: M. MIKE 2014-05-28 QA: A S-TAPER, FLATTED SHAFT, PANEL SEAL BUSHING, SOLDER HOOK TERMS - CHK: S. RAGHU 2014-08-05 1 SHEET TYPE I REV A 1 of 2 HONEYWELL CONFIDENTIAL THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION AND SUCH INFORMATION MAY NOT BE DISCLOSED TO OTHERS FOR ANY PURPOSE, NOR USED FOR MANUFACTURING PURPOSE'S WITHOUT WRITTEN PERMISSION FROM HONEYWELL PART NUMBER 4 2 3 1 SEE SHEET-2 TABLE CHARACTERISTICS D LISTING 392551M9725 ELECTRICAL RES ( ^ ) 5K ^ RES TOL A FLAT LENGTH IN [mm] .609 [15.47] MARKING 1 MECHANICAL B FLAT THICK IN [mm] C SHAFT LENGTH IN [mm] D BUSHNG LENGTH IN [mm] MTG HARDWARE LINE-1 .094 [2.39] .875 [22.23] .250 [6.35] UNASSEMBLED RV6SAYFD502B D LINE-2 LINE-3 LINE-4 5K ^ 20 YYWW MEXICO C C B B A A TITLE SIZE C 4 3 2 SCALE S-TAPER, FLATTED SHAFT, PANEL SEAL BUSHING, SOLDER HOOK TERMS CAGE CODE DWG NO NONE REF WT: - 392-MATRIX-IDWG-2 SEE NOTE 1 SHEET TYPE I 2 of 2 REV A