485025M8843

Installation Instructions for the 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers Issue A 50099565 GENERAL INFORMATION Potentiometers convert rotary motion into a change of resistance, supplying a smooth transition of voltage or current levels. The resulting voltage output may be used to control position transducers in a wide variety of potential applications. TABLE OF CONTENTS General Specifications . . . . . . . . front cover-5 The five series listed below are all 2 W plastic potentiometers and are available in resistances from 100 Ohm to 5 MOhm, inclusive. Available tapers include linear, log, and antilog to meet a wide range of application requirements. These single turn devices have a 6,35 mm [0.250 in] diameter shaft that is available in a range of lengths. Most shafts are nickel-plated brass. Most configurations have a standard 3/8-32 NEF-2A bushing; a high torque version is also available. Termination types are solder lug (with or without a center tap), PC pin or fast-on, all are solderdipped. Custom designs are available upon request. 380 Series: • 53C Series: • 380 Series: 2 W conductive plastic potentiometer offering low contact resistance variation and a long rotational life RV4 Series: Military version of the 380 Series; meets MIL-R-94 requirements (non RoHS compliant) Specific Configurations . . . . . . . . . . . . . . . 6 Order Guides. . . . . . . . . . . . . . . . . . . . . 7-13 RV4 Series: Specific Configurations . . . . . . . . . . . . . . 14 Order Guides. . . . . . . . . . . . . . . . . . . . 15-16 485 Series: Specific Configurations . . . . . . . . . . . . 17-19 Order Guides. . . . . . . . . . . . . . . . . . . . 20-29 Specific Configurations . . . . . . . . . . . . . . 30 Order Guides. . . . . . . . . . . . . . . . . . . . 31-35 385 Series: • 485 Series: Custom version of the 380 Series Specific Configurations . . . . . . . . . . . . 36-37 • 53C Series: Cost-effective version of the 380 Series Order Guides. . . . . . . . . . . . . . . . . . . . 38-44 • 385 Series: Custom version of the 53C Series Table 1. Electrical Specifications Characteristic Maximum working voltage: linear tapers log, reverse log tapers Dielectric strength Power rating Taper CRV1: linear tapers log, reverse log tapers Resistance 380 Series RV4 Series 485 Series 53C Series 500 Vdc 350 Vdc 1000 Vac for 60 s at 1 mPa [atm], 450 Vac for 60 s at 11,5 kPa [3.4 inHg] 2 W at 70 °C [158 °F], derated to 120 °C [248 °F] See Order Guide Tables under each series. 3% max. total resistance 3% max. total resistance 100 Ohm to 5 MOhm, inclusive. See Order Guide Tables under each series. Resistance tolerance See Order Guide Tables under each series. End resistance See Order Guide Tables under each series. Linearity Electrical rotation 385 Series ±5% See Order Guide Tables under each series. Contact resistance variation is the maximum momentary change in contact resistance that occurs when the wiper is moved from one location to another location. The larger this change, the more difficult it is to set the trimmer potentiometer and the more unstable the long term setting will be. 1 Sensing and Control 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 2. Mechanical Specifications Characteristic 380 Series RV4 Series 485 Series Shaft: material diameter nickel-plated beryllium copper nickel-plated brass Bushing: material thread nickel-plated brass nickel-plated brass 3/8-32 NEF-2A Termination base material thermoset brass; solder (SAC305) dip finish brass; solder (SAC305) dip or tin-lead finish brass; solder (SAC305) dip finish Housing material brass; solder (SAC305) dip or tin-lead finish stainless steel Base material thermoset plastic Mounting hardware material: jam nut mounting nut lock washer o-ring nickel-plated brass nickel-plated brass nickel-plated brass phospher bronze1 silicone rubber Operating torque See Order Guides under each series. Stop torque See Order Guides under each series. Weight (approx.) 1 385 Series nickel-plated brass1 6,35 mm [0.250 in] Retaining ring material Terminal material 53C Series 32,7 g [0.072 lb] Unless otherwise specified on the Order Guides under each series. Table 3. Environmental Specifcations Characteristic 380 Series RV4 Series Operating temperature 485 Series 53C Series 385 Series -55 °C to 120 °C [-67 °F to 248 °F] Rotational life tested to 25,000 cycles Table 4. Maximum Percent Temporary Resistance from 25 °C [77 °F] Nominal Resistance 2 Temperature -55 °C [-67 °F] -40 °C [-40 °F] 0 °C [32 °F] 25 °C [77 °F] 55 °C [131 °F] 85 °C [185 °F] 120 °C [248 °F] 100 Ohm ±5.0 ±4.0 ±1.5 0 ±1.5 ±2.0 ±3.5 10 kOhm +7.0 +5.5 +2.0 0 ±1.5 ±2.5 ±5.5 100 kOhm +8.0 +6.0 +2.5 0 ±2.0 ±3.5 ±6.0 1 MOhm +10.0 +8.0 +3.0 0 ±2.5 ±4.0 ±7.5 Honeywell Sensing and Control 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Figure 1. Electrical Taper Diagrams (For reference only.) Log (Z) Reverse Log (RZ) Linear: 2.5% to 97.5% (S-1) 90 90 80 80 80 70 60 50 40 30 Total Resistance (%) 100 90 Total Resistance (%) 100 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 5% to 95% (S-2) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 7.5% to 92.5% (S-3) 90 80 80 80 60 50 40 30 Total Resistance (%) 90 Total Resistance (%) 100 90 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 10% to 90% (S-4) 100 70 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Honeywell Sensing and Control 3 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Figure 2. Electrical Taper Diagrams (continued) Linear: 15% to 95% (S-5) Linear: 35% to 65% (S-7) 90 80 80 80 70 60 50 40 30 Total Resistance (%) 90 Total Resistance (%) 100 90 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 37.5% to 82.5% (S-8) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 42.5% to 57.5% (S-9) 80 80 60 50 40 30 Total Resistance (%) 90 80 Total Resistance (%) 100 90 Total Resistance (%) 100 90 70 70 60 50 40 30 60 50 40 30 20 20 10 10 10 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Linear: 10% to 40%; 57.5% to 82.5% (S-12) 90 80 80 80 60 50 40 Total Resistance (%) 90 Total Resistance (%) 100 90 Total Resistance (%) 100 70 60 50 40 60 50 40 30 20 20 20 10 10 10 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Honeywell Sensing and Control 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 70 30 0 0 Linear: 10% to 45%; 55% to 90% (S-13) 100 70 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 70 20 0 0 Linear: 45% to 55% (S-10) 100 Linear: 5% to 50%; 50% to 90% (S-11) 4 Linear: 25% to 75% (S-6) 100 30 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Figure 2. Electrical Taper Diagrams (continued) Linear: 35% to 45%; 55% to 65% (S-14) Linear: 45% to 47.5%; 47.5% to 52.5%; 52.5% to 55% (S-15) Linear: 5% to 40%; 45% to 52.5%; 60% to 95% (S-16) 90 80 80 80 70 60 50 40 30 Total Resistance (%) 100 90 Total Resistance (%) 100 90 Total Resistance (%) 100 70 60 50 40 30 70 60 50 40 30 20 20 20 10 10 10 0 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) 0 0 10 20 30 40 50 60 70 80 90 100 Angular Rotation, Clockwise Left to Right (%) Figure 3. Power Derating Curve 100 90 80 Rated Power (%) 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 Temperature (°C) 90 100 110 120 Figure 4. Mounting Hardware Jam Nut 7,94 mm [5/16 in] across flats 3,97 mm [5/32 in] thick Mounting Nut 1/4 x 32 thread 7,94 mm [5/16 in] across flats Lock Washer 10,32 mm [5/16 in] outside diameter 0,64 mm [0.025 in] thick O-Ring 6,35 mm [0.25 in] outside diameter 1,78 mm [0.070 in] thick Honeywell Sensing and Control 5 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 5. 380 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 380-A (See Table 380-A on p. 7.) flatted standard, 9,53 mm [0.375 in] 1 solder lug 380-C (See Table 380-C on p. 8.) flatted standard, 9,53 mm [0.375 in 1 PC pin 380-E (See Table 380-E on p. 10.) slotted high torque, 12,7 [0.500] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing AR TerminType Pin ation 380-B (See Table 380-B on p. 8.) slotted standard, 9,53 mm [0.375 in 2 solder lug 380-D (See Table 380-D on p. 9.) round standard, 9,53 mm [0.375 in 1 solder lug 380-F (See Table 380-F on p. 11.) slotted standard, 9,53 mm [0.375 in 1 solder lug 380-G (See Table 380-G on p. 12.) 380-H (See Table 380-H on p. 12.) standard, slotted 9,53 mm [0.375 in slotted 1 solder lug 380-I (See Table 380-I on p. 13.) standard, slotted 9,53 mm [0.375 in 6 2 solder lug Honeywell Sensing and Control standard, 9,53 mm [0.375 in 1 fast-on Configuration with Associated Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 380-A Order Guide 4 274 312 S-4 312 380000M8643 1k 10 4 4 274 312 S-4 312 380000M8682 50 k 10 4 4 274 312 S-4 312 380017M00071,2 500 10 4 4 274 312 S-4 312 380017M8606 10 k 10 4 4 274 312 S-4 312 380017M87681 25 k 10 4 4 274 312 S-4 312 380017M95501 5 k 10 4 4 274 312 S-4 312 no no no yes yes yes yes D Bushing Length (mm [in]) 4 no C Shaft Length (mm [in]) 10 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] B Flat Thickness (mm [in]) 380000M8630 2.5 k 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 6 [7-42] 6 [7-42] 6 [7-42] 6 [7-42] A Flat Length (mm [in]) 312 S-4 312 Dimensions Shaft Seal 274 Stop Torque (N m [in-lb]) Effective Electrical Rotation, Typ. (Degree) 4 Operating Torque (mN m [in-oz]) End Resistance at CCW, Max. (Ohm) 4 Mechanical Rotation (Degree) End Resistance at CW, Max. (Ohm) 10 380000M8629 Taper Resistance Tolerance (±%) 1k Catalog Listing Electrical Rotation, ±3 (Degree) Resistance (Ohm) Mechanical 7,95 [0.313] 7,95 [0.313] 14,30 [0.563] 7,95 [0.313] 7,95 [0.313] 7,95 [0.313] 7,95 [0.313] 7,95 [0.313] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 5,54 [0.218] 19,46 [0.766] 19,46 [0.766] 25,4 [1.000] 19,46 [0.766] 22,23 [0.875] 19,05 [0.750] 19,05 [0.750] 19,05 [0.750] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled no unassembled yes unassembled yes unassembled yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D A 3,18 [0.125] B Locating pin ø6,35 3X 1,57 [0.062] Terminal base 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] [0.250] 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] 22,25 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° Supplied with nickel-plated, phosphor bronze lock washer. Supplied with two mounting nuts. 1 2 Honeywell Sensing and Control 7 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 380-B Order Guide C D Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Flat Thickness (mm [in]) Shaft Seal A Flat Length (mm [in]) Dimensions Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 3800017M8956 10 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1-6 12 7,95 5,54 19,05 9,53 yes yes unassembled [7-42] [1.4] [0.313] [0.218] [0.750] [0.375] 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A 2X 3,18 [0.125] B Locating pin ø6,35 3X 1,57 [0.062] 22,25 Max. [0.875] 3/8-32 NEF-2A 90° Mounting surface 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] [0.250] 3X 1,57 [0.062] Terminal base 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 380-C Order Guide D Bushing Length (mm [in]) 9,53 5,54 22,23 9,27 yes [0.375] [0.218] [0.875] [0.365] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A B Locating pin 3,18 [0.125] 13,87 [0.546] ø6,35 [0.250] Terminal base 3/8-32 NEF-2A 32,77 Max. [1.290] 90° Mounting surface 3X 1,57 [0.062] 3X 1,02 [0.040] 8 Honeywell Sensing and Control 2X 5,08 [0.200] 0,635 [0.025] 3,18 Min. [0.125] RoHS Compliant C Shaft Length (mm [in]) yes B Flat Thickness (mm [in]) 1-6 12 [7-42] [1.4] A Flat Length (mm [in]) Shaft Seal 312 S-2 312 Dimensions Stop Torque (N m [in-lb]) 288 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 380096M9088 10 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 3 1 2 Left Center Right Mounting Hardware none 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 380-D Order Guide 312 S-4 312 380C11000 1000 10 4 4 274 312 S-4 312 380C1100K 100 k 10 4 4 274 312 S-4 312 380C110K 10 k 10 4 4 274 312 S-4 312 380C11MEG 1M 10 10 10 274 312 S-4 312 380C12000 2k 10 4 4 274 312 S-4 312 380C120K 20 k 10 4 4 274 312 S-4 312 380C1250 250 10 4 4 274 312 S-4 312 380C12500 2.5 k 10 4 4 274 312 S-4 312 380C125K 25 k 10 4 4 274 312 S-4 312 380C135K 35 k 10 4 4 274 312 S-4 312 380C1500 500 10 4 4 274 312 S-4 312 380C15000 5k 10 4 4 274 312 S-4 312 380C1500K 500 k 10 10 10 274 312 S-4 312 380C150K 50 k 10 4 4 274 312 S-4 312 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no 50,8 [2.000]) 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] no no no no no no no no no no no no no no RoHS Compliant 274 B Bushing Length (mm [in]) 4 A Shaft Length (mm [in]) Effective Electrical Rotation, Typ. (Degree) 4 Dimensions Shaft Seal End Resistance at CCW, Max. (Ohm) 10 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 100 Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) 380C1100 Taper Catalog Listing Resistance (Ohm) Mechanical Rotation (Degree) Mechanical Electrical Rotation, ±3 (Degree) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled no unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] 3,18 [0.125] Locating pin [0.250] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 0,635 [0.025] 22,25 Max. [0.875] 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 9 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 380-E Order Guide Bushing Length (mm [in]) RoHS Compliant Shaft Length (mm [in]) 4 274 312 S-4 312 1,60 1,19 15,88 12,7 1-4 12 yes unassembled no [0.063] [0.047] [0.625] [0.500] [7-28] [1.4] 380C210K 10 k 10 4 4 274 312 S-4 312 1,60 1,19 15,88 12,7 1-4 12 yes unassembled no [0.063] [0.047] [0.625] [0.500] [7-28] [1.4] 380C225K 25 k 10 4 4 274 312 S-4 312 1,60 1,19 15,88 12,7 1-4 12 yes unassembled no [0.063] [0.047] [0.625] [0.500] [7-28] [1.4] 380C25000 5k 10 4 4 274 312 S-4 312 1,60 1,19 15,88 12,7 1-4 12 yes unassembled no [0.063] [0.047] [0.625] [0.500] [7-28] [1.4] Slot Depth (mm [in]) 4 Shaft Seal 10 Stop Torque (N m [in-lb]) 1k Operating Torque (mN m [in-oz]) 380C2000 Taper Catalog Listing Effective Electrical Rotation, Typ. (Degree) D End Resistance at CCW, Max. (Ohm) C End Resistance at CW, Max. (Ohm) B Resistance Tolerance A Slot Width (mm [in]) Dimensions Resistance (Ohm) Mechanical Rotation (Degree) Mechanical Electrical Rotation, ±3 (Degree) Electrical Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A 90° 3,18 [0.125] Locating pin ø6,35 3X 1,57 [0.062] 10 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] Honeywell Sensing and Control B 22,25 Max. [0.875] Mounting surface 0,635 [0.025] 2X 20° 12,87 [0.546] [0.250] 3X 1,57 [0.062] 3,18 Min. [0.125] 1 Left 3 2 Right Center Mounting Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 380-F Order Guide 1k 10 4 4 274 312 S-4 312 380C3100K 100 k 10 4 4 274 312 S-4 312 380C310K 10 k 10 4 4 274 312 S-4 312 380C31MEG 1M 10 10 10 274 312 S-4 312 380C32000 2k 10 4 4 274 312 S-4 312 380C3200K 200 k 10 4 4 274 312 S-4 312 380C3250 250 10 4 4 274 312 S-4 312 380C32500 2.5 k 10 4 4 274 312 S-4 312 380C3250K 250 k 10 10 10 274 312 S-4 312 380C325K 25 k 10 4 4 274 312 S-4 312 380C3500 500 10 4 4 274 312 S-4 312 380C35000 5k 10 4 4 274 312 S-4 312 380C3500K 500 k 10 10 10 274 312 S-4 312 380C350K 50 k 10 4 4 274 312 S-4 312 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no no no no no no no 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] 1,60 1,19 22,23 9,53 [0.063] [0.047] [0.875] [0.375] RoHS Compliant 380C31000 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] 1-4 [7-28] D Bushing Length (mm [in]) 312 S-4 312 C Shaft Length (mm [in]) 274 B Slot Width (mm [in]) 4 Slot Length (mm [in]) Effective Electrical Rotation, Typ. (Degree) 4 Shaft Seal End Resistance at CCW, Max. (Ohm) 10 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 100 Dimensions A Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) 380C3100 Taper Catalog Listing Resistance (Ohm) Mechanical Rotation (Degree) Mechanical Electrical Rotation, ±3 (Degree) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled no unassembled no unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] C D 90° A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 1,57 [0.062] [0.250] Terminal base 0,635 [0.025] 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø27,79 3/8-32 NEF-2A Mounting surface 3,18 Min. [0.125] B 22,25 Max. [0.875] 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 11 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 380-G Order Guide RoHS Compliant 312 D Busing Length (mm [in]) 274 C Shaft Length (mm [in]) 10 B Slot Width (mm [in]) 25 Slot Depth (mm [in]) 380101M96991,2 2.5 M 10 Shaft Seal 312 Stop Torque (N m [in-lb]) 274 Dimensions A Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) 10 Taper Effective Electrical Rotation, Typ. (Degree) 5 3800000748500058 500 k Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 10 Catalog Listing Resistance (Ohm) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Electrical Mounting Hardware 1,60 1,19 22,23 9,53 12 yes unassembled no [0.063] [0.047] [0.875] [0.375] [1.4] 1,60 1,19 22,23 9,53 12 yes unassembled yes [0.063] [0.047] [0.875] [0.375] [1.4] 1-6 [7-42] 1-6 Z 312 [7-42] Z 312 Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C D ø27,79 Max. [1.094] 13,49 [0.531] 90° 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] Locating pin 3X 2,36 [0.093] 3X 3,15 [0.124] 2 B 3/8-32 NEF-2A 22,25 Max. [0.875] Mounting surface 0,635 [0.025] 2X 20° 12,87 [0.546] [0.250] Terminal base 3X 1,57 [0.062] 1 ø6,35 1 Left 3 2 Center Right 3,18 Min. [0.125] Supplied with stainless-steel shaft. Supplied with nickel-plated beryllium copper retaining ring. Table 380-H Order Guide 312 S-2 312 Dimensional Drawings (For reference only: mm [in].) C D C D Shaft Length (mm [in]) Bushing Length (mm [in]) ø27,79 Max. [1.094] 13,49 [0.531] 90° 2,77 [0.109] A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 1,27 [0.050] 3X ø1,14 [0.045] 3X 3,96 [0.156] 3X 2,79 [0.110] 12 Honeywell Sensing and Control 3X 1,73 [0.068] 2X 20° 12,87 [0.546] ø6,35 [0.250] Terminal base 0,56 [0.022] Mounting Hardware 6-20 12 1,60 1,19 22,23 9,53 no yes unassembled [42-141] [1.4] [0.063] [0.047] [0.875] [0.375] Shown with 50% shaft rotation 14,30 [0.563] RoHS Compliant B Slot Width (mm [in]) Slot Length (mm [in]) 288 Shaft Seal 4 Dimensions A Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 1k Taper End Resistance at CW, Max. (Ohm) 380099M9425 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical B 27,38 Max. [1.078] 3/8-32 NEF-2A Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 380-I Order Guide C D Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Slot Width (mm [in]) Slot Depth (mm [in]) 310 Shaft Seal 4 Dimensions A Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 1k Taper End Resistance at CW, Max. (Ohm) 380036M7444 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware 1-4 12 1,60 1,19 22,23 9,53 no yes unassembled [7-28] [1.4] [0.063] [0.047] [0.875] [0.375] 344 S-3 360 Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] C D ø27,79 Max. [1.094] 13,49 [0.531] 90° 2,77 [0.109] A 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 12,87 [0.546] [0.250] Terminal base 0,635 [0.025] 3/8-32 NEF-2A B 22,25 Max. [0.875] Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Honeywell Sensing and Control 13 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 6. RV4 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination Configuration with Associated Hardware Shaft Type Bushing AR Type Pin Termination RV4-A (See Table RV4-A on p. 15.) RV4-B (See Table RV4-B on p. 16.) high torque, slotted 12,7 mm [0.500 in] slotted 14 1 solder lug Honeywell Sensing and Control standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table RV4-A Order Guide 274 312 S-4 312 RV4LAYSD103A 10 k 10 4 4 274 312 S-4 312 RV4LAYSD104A 100 k 10 4 4 274 312 S-4 312 RV4LAYSD502A 5k 10 4 4 274 312 S-4 312 RV4LAYSD504A 500 k 10 10 10 274 312 S-4 312 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no B Shaft Bushing Length Length (mm [in]) (mm [in]) 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] RoHS Compliant 4 Shaft Seal Electrical Rotation, ±3 (Degree) 4 Stop Torque (N m [in-lb]) Effective Electrical Rotation, Typ. (Degree) 10 Dimensions A Operating Torque (mN m [in-oz]) End Resistance at CCW, Max. (Ohm) 1k Mechanical Rotation (Degree) End Resistance at CW, Max. (Ohm) RV4LAYSD102A Taper Catalog Listing Reistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] 11,9 [0.047] A B 1,6 [0.063] 3,18 [0.125] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 Locating pin 12,87 [0.546] 22,23 Max. [0.875] [0.250] 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 3,18 Min. [0.125] 90° 1 Left 3 Right 2 Center 2X 20° Honeywell Sensing and Control 15 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table RV4-B Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 4 274 312 S-4 312 RV4NAYSB103A 10 k 10 4 4 274 312 S-4 312 RV4NAYSB503A 50 k 10 4 4 274 312 S-4 312 RV4NAYSK103A 10 k 10 4 4 274 312 S-4 312 RV4NAYSK502A 5k 10 4 4 274 312 S-4 312 RV4SAYSD502A 5 10 - - 274 312 S-4 312 RV4NAYSD503D 50 k 20 500 4 274 312 Z 312 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] yes yes yes yes yes yes yes B Shaft Bushing Length Length (mm [in]) (mm [in]) 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 63,5 [2.500] 63,5 [2.500] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 10 Shaft Seal End Resistance at CCW, Max. (Ohm) 100 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) RV4NAYSB101A Dimensions A Operating Torque (mN m [in-oz]) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 2,77 [0.109] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 16 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 2X 20° Honeywell Sensing and Control 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 Right 2 Center Mounting Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 7. 485 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 485-A (See Table 485-A on p. 20.) standard, flatted 9,53 mm [0.375 in] 1 solder lug 485-C (See Table 485-C on p. 21.) round standard, 6,35 mm [0.250 in] 1 solder lug with center tap 485-E (See Table 485-E on p. 22.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-G (See Table 485-G on p. 23.) round standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing AR Type Pin Termination Configuration with Associated Hardware 485-B (See Table 485-B on p. 20.) standard, flatted 9,53 mm [0.375 in] 1 solder lug with center tap 485-D (See Table 485-D on p. 21.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-F (See Table 485-F on p. 22.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-H (See Table 485-H on p. 23.) standard, slotted 9,53 mm [0.375 in] 1 solder lug with center tap Honeywell Sensing and Control 17 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 7. 485 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 485-I (See Table 485-I on p. 24.) standard, 6,35 mm [0.250 in] slotted and 9,53 mm [0.375 in] 1 solder lug 485-K (See Table 485-K on p. 25.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 485-M (See Table 485-M on p. 26.) slotted standard, 7,9 mm [0.312 in] 1 solder lug 485-O (See Table 485-O on p. 27.) slotted 18 standard, 12,7 mm [0.500 in] 1 solder lug Honeywell Sensing and Control Configuration with Associated Hardware Shaft Type Bushing AR Type Pin Termination 485-J (See Table 485-J on p. 24.) slotted standard, 8,69 mm [0.342 in] 0 solder lug 485-L (See Table 485-L on p. 25.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 485-N (See Table 485-N on p. 26.) standard, 9,53 mm [0.375 in] slotted and 12,7 mm [0.500 in] 1 solder lug 485-P (See Table 485-P on p. 27.) slotted standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 7. 485 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 485-Q (See Table 485-Q on p. 28.) standard, slotted 9,53 mm [0.375 in] 1 solder lug with center tap 485-S (See Table 485-S on p. 29.) slotted standard, 12,7 mm [0.500 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing AR Type Pin Termination Configuration with Associated Hardware 485-R (See Table 485-R on p. 28.) round standard, 9,53 mm [0.375 in] 1 solder lug 485-T (See Table 485-T on p. 29.) standard, straight 8,67 mm knurled [0.342 in] 1 solder lug Honeywell Sensing and Control 19 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-A Order Guide 312 S-7 312 B C D 2,77 [0.109] Flat Thickness (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) Mounting Hardware 1-4 12 11,13 5,54 22,23 9,53 no yes unassembled [7-28] [1-4] [0.438] [0.218] [0.875] [0.375] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] RoHS Compliant A Flat Length (mm [in]) 112 Dimensions Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485000M8990 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Locating pin 12,87 [0.546] ø6,35 [0.250] B 0,635 [0.025] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Terminal base Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-B Order Guide Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] D Bushing Length (mm [in]) Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D A 22,23 Max. [0.875] 3,18 [0.125] 4X 1,57 [0.062] 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] 20 2X 20° Honeywell Sensing and Control Terminal base 12,87 [0.546] ø6,35 B [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] Mounting Hardware 11,13 5,54 22,23 9,53 yes unassembled [0.438] [0.218] [0.875] [0.375] C Locating pin RoHS Compliant C Shaft Length (mm [in]) no B Flat Thickness (mm [in]) 12 A Flat Length (mm [in]) Shaft Seal 312 S-9 312 S-14 Dimensions Stop Torque (N m [in-lb]) 112 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485025M9052 10 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-C Order Guide 485025M9267 5k 10 4 4 112 A B Shaft Length (mm [in]) Bushing Length (mm [in]) 15,88 [0.625] 15,88 [0.625] 6,35 [0.250] 6,35 [0.250] 1-4 12 no [7-28] [1.4] 1-4 12 312 S-13 312 no [7-28] [1.4] 312 S-13 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] yes unassembled 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 3/8-32 NEF-2A 0,635 [0.025] yes unassembled 22,23 Max. [0.875] 3,18 [0.125] Terminal base Mounting Hardware Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 4X 1,57 [0.062] RoHS Compliant 112 Shaft Seal 4 Dimensions Stop Torque (N m [in-lb]) Effective Electrical Rotation, Typ. (Degree) 4 Operating Torque (mN m [in-oz]) End Resistance at CCW, Max. (Ohm) 10 Mechanical Rotation (Degree) End Resistance at CW, Max. (Ohm) 10 k Taper Resistance Tolerance (±%) 485025M8843 Mechanical Electrical Rotation, ±3 (Degree) Catalog Listing Resistance (Ohm) Electrical 1 Left Mounting surface 3 2 Right Center 3,18 Min. [0.125] 2X 20° Table 485-D Order Guide 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] A B Shaft Length (mm [in]) Bushing Length (mm [in]) 22,23 [0.875] 9,53 [0.375] 1-6 12 yes [7-42] [1.4] RoHS Compliant 284 Dimensions Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485008M7167 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Terminal base 12,87 [0.546] ø6,32 Locating pin [0.249] 22,23 Max. [0.875] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 21 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 485-E Order Guide 1-4 12 no [7-28] [1.4] 312 S-16 312 A B Shaft Length (mm [in]) Bushing Length (mm [in]) 50,8 [2.000] 9,53 [0.375] RoHS Compliant 284 Shaft Seal 4 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485000M8930 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation A ø27,79 Max. B 2,77 [0.109] [1.094] 13,49 [0.531] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] ø6,35 12,87 [0.546] [0.25] Locating pin 3X 2,36 [0.093] 3X 3,15 [0.124] 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 2X 20° Mounting surface 0,635 [0.025] 1 Left 3,18 Min. [0.125] 3 2 Right Center Table 485-F Order Guide 312 S-11 312 1-4 12 [7-28] [1.4] no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 31,75 [1.250] 9,53 [0.375] Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 22 [0.250] 0,635 [0.025] 2X 20° Honeywell Sensing and Control 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 Locating pin Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center RoHS Compliant 284 Shaft Seal 100 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 10 k Taper End Resistance at CW, Max. (Ohm) 485000M9156 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-G Order Guide 348 S-6 360 1-4 [7-28] - no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 76,2 [3.000] 9,53 [0.375] RoHS Compliant 180 Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Dimensions Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 25 k Taper End Resistance at CW, Max. (Ohm) 485004M8986 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A B 2,77 [0.109] ø1,58 [0.062] 2,39 [0.094] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Locating pin 22,23 Max. [0.875] [0.249] Mounting surface 0,635 [0.025] 12,87 [0.546] 3,18 [0.125] ø6,32 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-H Order Guide Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] 12 1,60 1,19 no [1.4] [0.063] [0.047] 12 1,60 1,19 no [1.4] [0.063] [0.047] RoHS Compliant D Bushing Length (mm [in]) 263 C Shaft Length (mm [in]) 4 B Slot Width (mm [in]) 4 Slot Length (mm [in]) 10 1k Shaft Seal 485042M9576 1-6 [7-42] 1-6 312 S-8 312 [7-42] 312 S-8 312 Dimensions A Stop Torque (N m [in-lb]) 263 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper Effective Electrical Rotation, Typ. (Degree) 10 Electrical Rotation, ±3 (Degree) End Resistance at CCW, Max. (Ohm) 485025M9428 10 k Catalog Listing Resistance (Ohm) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Electrical Mounting Hardware 22,23 9,53 yes unassembled [0.875] [0.375] 22,23 9,53 yes unassembled [0.875] [0.375] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D A 22,23 Max. [0.875] 3,18 [0.125] 3X 1,57 [0.062] 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin Terminal base B [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 23 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-I Order Guide 284 485000M9641 10 k 10 4 4 284 485000M9708 10 4 4 284 1k Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 15,88 [0.625] 9,53 [0.375] 9,53 [0.75] 9,53 [0.375] 6,35 [0.250] Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] RoHS Compliant 4 D Bushing Length (mm [in]) 4 1,60 [0.063] 1,60 no [0.063] 1,60 no [0.063] 1,60 no [0.063] no C Shaft Length (mm [in]) 10 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] B Slot Width (mm [in]) 485000M9564 50 k 1-4 [1-28] 1-4 312 S-9 312 [1-28] 1-4 312 S-9 312 [1-28] 1-4 312 S-9 312 [1-28] 312 S-9 312 Slot Length (mm [in]) 284 Shaft Seal 4 A Stop Torque (N m [in-lb]) 4 Dimensions Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485000M8723 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical A 3,18 [0.125] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin 3X 1,57 [0.062] [0.250] 3 2 Right Center 1 Left Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A 3,18 Min. [0.125] 2X 20° Table 485-J Order Guide 312 S-4 312 D 14,30 [0.563] Bushing Length (mm [in]) Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D A 3,18 [0.125] 12,87 [0.546] ø6,35 [0.250] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 24 Honeywell Sensing and Control 3/8-32 NEF-2A Terminal base 2X 20° Mounting surface 0,635 [0.025] Mounting Hardware 1-4 12 1,60 1,19 50,8 9,53 no yes unassembled [1-28] [1.4] [0.063] [0.047] [2.000] [0.375] Dimensional Drawings (For reference only: mm [in].) 2,77 [0.109] RoHS Compliant C Shaft Length (mm [in]) Slot Depth (mm [in]) Shaft Seal B Slot Width (mm [in]) Dimensions A Stop Torque (N m [in-lb]) 284 Operating Torque (mN m [in-oz]) 10 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 10 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485000M9017 1 M Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-K Order Guide 311 S-7 312 D RoHS Compliant C Bushing Length (mm [in]) Slot Width (mm [in]) Shaft Seal B Slot Depth (mm [in]) A Shaft Length (mm [in]) Dimensions Stop Torque (N m [in-lb]) 284 Operating Torque (mN m [in-oz]) 100 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485042M9668 10 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1-6 12 1,60 1,19 22,23 9,53 yes yes unassembled [7-42] [1.4] [0.063] [0.047] [0.875] [0.375] Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. C [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-L Order Guide 312 S-2 312 Dimensional Drawings (For reference only: mm [in].) A [0.250] 3X 1,57 [0.062] Bushing Length (mm [in]) RoHS Compliant Shaft Length (mm [in]) Mounting Hardware ø27,79 Max. [1.094] 13,49 [0.531] B C ø6,35 3X 2,36 [0.093] 3X 3,15 [0.124] D Shown with 50% shaft rotation 14,30 [0.563] 2,77 [0.109] 3,18 [0.125] 12,87 [0.546] 3/8-32 NEF-2A Locating pin Terminal base C 1-4 12 1,60 1,19 22,23 9,53 no yes unassembled [7-28] [1.4] [0.063] [0.047] [0.875] [0.375] D 3X 1,57 [0.062] B Slot Width (mm [in]) Slot Depth (mm [in]) 304 A Shaft Seal 10 Dimensions Stop Torque (N m [in-lb]) 10 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 1M Taper End Resistance at CW, Max. (Ohm) 485000M8911 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 25 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-M Order Guide 312 S-9 312 Dimensional Drawings (For reference only: mm [in].) C D Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Slot Width (mm [in]) Slot Depth (mm [in]) 33 Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Dimensions A Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485010M6860 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware 1,60 1,19 27,19 7,92 1-4 12 yes unassembled no [0.063] [0.047] [1.031] [0.312] [7-28] [1.4] 14,30 [0.563] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] B D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° 4 4 45 485008M8967 5k 10 4 4 45 485008M9458 5k 10 4 4 45 485008M9687 5k 10 4 4 45 485008M9688 5k 10 4 4 45 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 20,62 [0.182] 50,8 [2.000] 50,8 [2.000] 50,8 [2.000] 47,63 [1.875] 39,88 [1.570] 12,7 [0.500] 12,7 [0.500] 12,7 [0.500] 9,53 [0.375] 9,53 [0.375] 12,7 [0.500] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] Bushing Length (mm [in]) 10 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] Shaft Length (mm [in]) 5k 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] D Slot Width (mm [in]) 485008M0002 1-6 312 S-10 312 [7-42] 1-6 312 S-10 312 [7-42] 1-6 312 S-10 312 [7-42] 1-6 312 S-10 312 [7-42] 1-6 312 S-10 312 [7-42] 1-6 312 S-A 312 [7-42] Slot Depth (mm [in]) 45 Shaft Seal 4 A Stop Torque (N m [in-lb]) 4 Dimensions B C Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485000M8990 Catalog Listing Electrical Rotation, ±3 (Degree) Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical A 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 26 Honeywell Sensing and Control 2X 20° 12,87 [0.546] ø6,35 Locating pin [0.250] 22,23 Max. [0.875] 3/8-32 NEF-2A 90° 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center RoHS Compliant Table 485-N Order Guide Mounting Hardware yes unassembled no unassembled yes unassembled yes unassembled yes unassembled yes unassembled 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-O Order Guide 312 S-10 312 C D Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Slot Width (mm [in]) Slot Depth (mm [in]) Shaft Seal Stop Torque (N m [in-lb]) 45 Dimensions A Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485008M0004 5 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1,60 1,19 25,4 12,7 1-6 12 no unassembled yes [0.063] [0.047] [1.000] [0.500] [7-42] [1.4] Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. C [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] 3X 1,57 [0.062] [0.250] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin Mounting surface 0,635 [0.025] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-P Order Guide 312 S-10 312 D Bushing Length (mm [in]) RoHS Compliant C Shaft Length (mm [in]) Slot Depth (mm [in]) Shaft Seal B Slot Width (mm [in]) Dimensions A Stop Torque (N m [in-lb]) 46 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485000M9651 20 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1-4 12 1,60 1,19 50,8 9,53 no yes unassembled [7-28] [1.4] [0.063] [0.047] [2.000] [0.375] Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] Terminal base 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 27 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-Q Order Guide RoHS Compliant D Bushing Length (mm [in]) no C Shaft Length (mm [in]) - B Slot Width (mm [in]) 1-4 348 S-12 360 Slot Depth (mm [in]) Shaft Seal A Stop Torque (N m [in-lb]) 270 Dimensions Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485030M9652 10 k Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1,60 1,19 50,8 9,53 yes unassembled [0.063] [0.047] [2.000] [0.375] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 22,56 Max. [0.888] 3,18 [0.125] 4X 1,57 [0.062] Terminal base 4X 2,36 [0.093] 4X 3,15 [0.124] 4X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 0,635 [0.025] 22,23 Max. [0.875] 90° Mounting surface 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 485-R Series Order Guide 312 S-5 312 1-4 12 no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 63,5 [2.500] 9,53 [0.375] RoHS Compliant Shaft Seal 250 Stop Torque (N m [in-lb]) 4 Dimensions Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 10 Taper End Resistance at CCW, Max. (Ohm) 1k Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485040M9512 Resistance Tolerance (±%) Catalog Listing Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] D Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C ø2,36 2,77 [0.109] 49,40 [1.945] [0.093] 5,70 [0.226] 3,18 [0.125] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 28 Locating pin 2X 20° Honeywell Sensing and Control 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 12,7 [0.125] 12,7 [0.125] 12,87 [0.546] 22,23 Max. [0.875] ø6,35 [0.250] 1 Left 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 485-S Order Guide 312 S-15 312 1-6 C D Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Slot Width (mm [in]) Slot Depth (mm [in]) 45 A Shaft Seal 4 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 5 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 485048M9728 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware 0,23 1,19 25,15 12,7 no unassembled [0.009] [0.047] [0.990] [0.500] 12 yes Dimensional Drawings (For reference only: mm [in].) Shown with 50% shaft rotation 14,30 [0.563] ø27,79 Max. C [1.094] 13,49 [0.531] D 2,77 [0.109] A 7,32 [0.288] B 3,18 [0.125] 5,64 [0.222] 3X 1,57 [0.062] Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin [0.250] 3/8-32 NEF-2A 0,635 [0.025] 22,23 Max. [0.875] 90° Mounting surface 3 1 2 Left Center Right 3,18 Min. [0.125] 2X 20° Table 485-T Order Guide 348 S-8 360 1-4 - no A B Shaft Length (mm [in]) Bushing Length (mm [in]) 19,05 [0.750] 8,69 [0.342] Dimensional Drawings (For reference only: mm [in].) 2,77 [0.109] ø6,35 [0.250] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] yes unassembled ø27,79 Max. [1.094] 13,49 [0.531] A B 3,18 [0.125] 12,87 [0.546] Locating pin Terminal base Mounting Hardware Shown with 50% shaft rotation 14,30 [0.563] 3X 1,57 [0.062] RoHS Compliant Shaft Seal 158 Stop Torque (N m [in-lb]) 4 Dimensions Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 10 Taper End Resistance at CCW, Max. (Ohm) 20 k Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 485022M8995 Resistance Tolerance (±%) Catalog Listing Mechanical Resistance (Ohm) Electrical 22,23 Max. [0.875] 3/8-32 NEF-2A Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 29 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 8. 53C Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 53C1 (See Table 53C1 on pp. 31-32.) round standard, 9,53 mm [0.375 in] 1 solder lug 53C3 (See Table 53C3 on pp. 34-35.) slotted 30 standard, 6,35 mm [0.25 in] 1 solder lug Honeywell Sensing and Control Configuration with Associated Hardware Shaft Type Bushing AR TerminType Pin ation 53C2 (See Table 53C2 on p. 33.) high torque, slotted 12,7 mm [0.500 in] 1 solder lug Configuration with Associated Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 53C1 Order Guide 312 S-4 53C1100K 100 k 10 4 4 274 312 S-4 53C110K 10 k 10 4 4 274 312 S-4 53C110MEG 10 M 20 10 10 274 312 S-4 53C11500 1.5 k 10 4 4 274 312 S-4 53C115K 15 k 10 4 4 274 312 S-4 53C11K 1k 10 4 4 274 312 S-4 53C11MEG 1M 20 10 10 274 312 S-4 53C120k 20 k 10 4 4 274 312 S-4 53C1250 250 10 4 4 274 312 S-4 53C12500 2.5 k 10 4 4 274 312 S-4 53C1250K 250 k 10 10 10 274 312 S-4 53C125K 25 k 10 4 4 274 312 S-4 53C12K 2k 10 4 4 274 312 S-4 53C135k 35 k 10 4 4 274 312 S-4 53C150 50 k 10 4 4 274 312 S-4 53C1500 500 10 4 4 274 312 S-4 53C1500k 500 k 10 10 10 274 312 S-4 53C150k 50 k 10 4 4 274 312 S-4 53C15K 5k 10 4 4 274 312 S-4 53C15meg 5M 20 10 10 274 312 S-4 53c1sw100k 100 k 10 4 4 274 312 S-4 53c1sw10k 10 4 4 274 312 S-4 10 k 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 1-6 312 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no no no no no no no no no no no no no no no B Shaft Bushing Length Length (mm [in]) (mm [in]) 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 19,05 [2.00] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant 274 Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Dimensions A Operating Torque (mN m [in-oz]) Taper 10 53C1100 Mechanical Rotation (Degree) Electrical Rotation, ±3 (Degree) 100 Catalog Listing End Resistance at CW, Max. (Ohm) End Resistance at CCW, Max. (Ohm) Effective Electrical Rotation, Typ. (Degree) Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled (Continued on next page.) Honeywell Sensing and Control 31 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 53C1 Order Guide (continued) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 1k 4 274 312 Z 312 53c110KZ 10 k 10 100 4 274 312 Z 312 53c11MEGZ 1M 20 10 k 10 274 312 Z 312 53c1250KZ 250 k 10 2.5 k 10 274 312 Z 312 53c125KZ 25 k 10 250 4 274 312 Z 312 53c1500KZ 500 k 10 5k 10 274 312 Z 312 53c150KZ 50 k 10 500 4 274 312 Z 312 53c15KZ 5k 10 50 4 274 312 Z 312 100 k 10 1k 4 274 312 RZ 312 53C1-100K-RZ 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] no no no no no no no no no B RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 10 Shaft Seal End Resistance at CCW, Max. (Ohm) 100 k A Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 53c1100KZ Catalog Listing Dimensions Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled yes unassembled Shaft Bushing Length Length (mm [in]) (mm [in]) 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 50,8 [2.00] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] A Shown with 50% shaft rotation ø27,79 Max. B 2,77 [0.109] 3,18 [0.125] [1.094] 13,49 [0.531] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 32 Locating pin 3/8-32 NEF-2A Mounting surface Terminal base 0,64 [0.025] 2X 20° Honeywell Sensing and Control 12,87 [0.546] ø6,35 [0.250] 22,23 Max. [0.875] 1 Left 3,18 Min. [0.125] 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 53C2 Order Guide Dimensions 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2100K 100 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C210K 10 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C21500 1.5 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2150K 150 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C215K 15 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C21K 1k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C21MEG 1M 10 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 2.5 M 20 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C220K 20 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2250 250 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C22500 2.5 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2250K 250 k 10 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C225K 25 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C22K 2k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C22MEG 2M 20 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 3.5 M 20 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C250 50 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2500 500 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C2500K 500 k 10 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C250K 50 k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C25K 5k 10 4 4 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C25MEG 5M 20 10 10 274 312 S-4 312 1-6 [7-42] 12 [1.4] no 15,88 [0.625] 12,7 [0.500] no unassembled 53C22.5MEG 53C23.5MEG Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 2,77 [0.109] A RoHS Compliant 4 Shaft Seal Mechanical Rotation (Degree) 10 53C2100 Stop Torque (N m [in-lb]) Taper 100 Catalog Listing Operating Torque (mN m [in-oz]) Electrical Rotation, ±3 (Degree) Bushing Length (mm [in]) Effective Electrical Rotation, Typ. (Degree) Shaft Length (mm [in]) End Resistance at CCW, Max. (Ohm) B End Resistance at CW, Max. (Ohm) A Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] 11,9 [0.047] B 1,6 [0.063] 3,18 [0.125] ø12,7 [0.500] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] ø6,35 Locating pin 12,87 [0.546] 22,23 Max. [0.875] [0.250] 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 3,18 Min. [0.125] 90° 3 1 Right 2 Left Center 2X 20° Honeywell Sensing and Control 33 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 53C3 Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 274 312 S-4 312 53C3100K 100 k 10 4 4 274 312 S-4 312 53C310K 10 k 10 4 4 274 312 S-4 312 53C3150 150 10 4 4 274 312 S-4 312 53C31500 1.5 k 10 4 4 274 312 S-4 312 53C3150K 150 k 10 4 4 274 312 S-4 312 53C315K 15 k 10 4 4 274 312 S-4 312 53C31K 1k 10 4 4 274 312 S-4 312 53c31k/new 1k 10 4 4 274 312 S-4 312 53C31MEG 1M 10 10 10 274 312 S-4 312 53C32.5MEG 2.5 M 20 10 10 274 312 S-4 312 53C3200K 200 k 10 4 4 274 312 S-4 312 53c320k 20 k 10 4 4 274 312 S-4 312 53C3250 250 10 4 4 274 312 S-4 312 53C32500 2.5 k 10 4 4 274 312 S-4 312 53C3250K 250 k 10 10 10 274 312 S-4 312 53C325K 25 k 10 4 4 274 312 S-4 312 53C32K 2k 10 4 4 274 312 S-4 312 53c32MEG 2M 20 10 10 274 312 S-4 312 53c3350 350 10 4 4 274 312 S-4 312 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] (Continued on next page.) 34 Honeywell Sensing and Control no no no no no no no no no no no no no no no no no no no no B Shaft Bushing Length Length (mm [in]) (mm [in]) 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 4 Shaft Seal End Resistance at CCW, Max. (Ohm) 10 53C3100 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 100 Catalog Listing Dimensions A Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 53C3 Order Guide (continued) Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 4 274 312 S-4 312 53c350 50 10 4 4 274 312 S-4 312 53c3500 500 10 4 4 274 312 S-4 312 500 k 10 10 10 274 312 S-4 312 53c3500k/new 500 k 10 10 10 274 312 S-4 312 53c350k 50 k 10 4 4 274 312 S-4 312 53c35k 5k 10 4 4 274 312 S-4 312 53C35MEG 5M 20 10 10 274 312 S-4 312 53C3750k 750 k 10 4 4 274 312 S-4 312 53C375K 75 k 10 4 4 274 312 S-4 312 53c3500k 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] B Shaft Bushing Length Length (mm [in]) (mm [in]) 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] 22,23 [0.875] no no no no no no no no no no 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 4 Shaft Seal End Resistance at CCW, Max. (Ohm) 10 53c33500 Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 3.5 k Catalog Listing Dimensions A Operating Torque (mN m [in-oz]) Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 2,77 [0.109] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base Mounting surface 0,64 [0.025] 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Honeywell Sensing and Control 35 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 9. 385 Series Specific Configurations Shaft Type Bushing AR Type Pin Termination 385-A (See Table 385-A on p. 38.) flatted standard, 9,53 mm [0.375 in] 1 solder lug 385-C (See Table 385-C on p. 39.) flatted standard, 1 9,53 mm and [0.375 in] 2 solder lug Configuration with Associated Hardware Shaft Type Bushing AR Type Pin Termination 385-B (See Table 385-B on p. 38.) round standard, 9,53 mm [0.375 in] 1 solder lug 385-D (See Table 385-D on p. 39.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-E (See Table 385-E on p. 40.) 385-F (See Table 385-F on p. 40.) high torque, slotted 12,7 mm [0.500 in] high torque, slotted 12,7 mm [0.500 in] 1 solder lug 1 solder lug 385-G (See Table 385-G on p. 41.) 385-H (See Table 385-H on p. 41.) high torque, slotted 12,7 mm [0.500 in] standard, 9,53 mm slotted [0.375 in] 36 1 solder lug Honeywell Sensing and Control 1 solder lug Configuration with Associated Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 Table 9. 385 Series Specific Configurations (continued) Shaft Type Bushing AR Type Pin Termination 385-I (See Table 385-I on p. 42.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-K (See Table 385-K on p. 43.) slotted standard, 9,53 mm [0.375 in] 1 solder lug Configuration with Associated Hardware Shaft Type Bushing AR TerminType Pin ation Configuration with Associated Hardware 385-J (See Table 385-J on p. 43.) slotted standard, 9,53 mm [0.375 in] 1 solder lug 385-L (See Table 385-L on p. 44.) slotted standard, 9,53 mm [0.375 in] 1 solder lug Honeywell Sensing and Control 37 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-A Order Guide 4 274 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 12,27 5,53 12 [1.4] no [0.483] [0.218] 9,53 3,96 12 [1.4] no [0.375] [0.156] C RoHS Compliant 4 D Bushing Length (mm [in]) 10 C Shaft Length (mm [in]) 5k B Flat Thickness (mm [in]) 385000M9136 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] A Flat Length (mm [in]) 274 Shaft Seal 4 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 10 k Taper End Resistance at CW, Max. (Ohm) 385000M5783 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware 22,23 9,53 [0.875] [0.375] yes unassembled 22,23 9,53 [0.875] [0.375] yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A 3,18 [0.125] ø6,35 Locating pin 3X 1,57 [0.062] B 3/8-32 NEF-2A 0,635 [0.025] 3X 1,57 [0.062] 22,23 Max. [0.875] 90° Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] [0.250] 1 Left Mounting surface 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Table 385-B Order Guide 385500M5694 5k 10 4 4 274 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] C Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 38 Honeywell Sensing and Control Locating pin B 0,635 [0.025] 2X 20° ø6,35 [0.250] 3/8-32 NEF-2A Terminal base Mounting surface 3,18 Min. [0.125] Mounting Hardware 12 9,53 5,53 22,23 9,53 [1.4] no [0.375] [0.218] [0.875] [0.375] no unassembled 12 9,53 5,53 22,23 9,53 [1.4] no [0.375] [0.218] [0.875] [0.375] no unassembled 12 9,53 5,53 22,23 9,53 [1.4] no [0.375] [0.218] [0.875] [0.375] no unassembled D 2,77 [0.109] RoHS Compliant 274 D Bushing Length (mm [in]) 4 C Shaft Length (mm [in]) 4 B Flat Thickness (mm [in]) 10 A Flat Length (mm [in]) 1k Dimensions Shaft Seal 385500M4863 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper Effective Electrical Rotation, Typ. (Degree) 10 Electrical Rotation, ±3 (Degree) End Resistance at CCW, Max. (Ohm) 385500M0012 100 k Catalog Listing Resistance (Ohm) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Electrical 12,87 [0.546] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-C Order Guide 4 274 312 S-4 312 385000M9168 100 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Operating Torque (mN m [in-oz]) 1-4 12 [7-28] [1.4] no 1-4 12 [7-28] [1.4] no C B Shaft Bushing Length Length (mm [in]) (mm [in]) 19,05 [0.750] 19,05 [0.750] 9,53 [0.375] 9,53 [0.375] RoHS Compliant Electrical Rotation, ±3 (Degree) 4 Shaft Seal Effective Electrical Rotation, Typ. (Degree) 10 Dimensions A Stop Torque (N m [in-lb]) End Resistance at CCW, Max. (Ohm) 150 Mechanical Rotation (Degree) End Resistance at CW, Max. (Ohm) 385000M8551 Taper Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled yes unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 [0.250] Locating pin 1 Left Mounting surface 0,635 [0.025] 3 2 Right Center 3,18 Min. [0.125] 2X 20° Table 385-D Order Guide Electrical Rotation, ±3 (Degree) Taper Mechanical Rotation (Degree) 100 4 274 312 Z 312 B Shaft Bushing Length Length (mm [in]) (mm [in]) 25,4 [1.000] 1-4 12 no [7-28] [1.4] 9,53 [0.375] RoHS Compliant Effective Electrical Rotation, Typ. (Degree) 10 Shaft Seal End Resistance at CCW, Max. (Ohm) 10 k Dimensions A Stop Torque (N m [in-lb]) End Resistance at CW, Max. (Ohm) 385000M8659 Operating Torque (mN m [in-oz]) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Mounting Hardware yes unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] C Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 22,23 Max. [0.875] 3/8-32 NEF-2A Terminal base 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 1 Left 3 2 Right Center 2X 20° Honeywell Sensing and Control 39 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-E Order Guide 14,30 [0.563] C D Slot Thickness (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) RoHS Compliant B Mounting Hardware 1-4 12 1,60 1,19 15,88 12,7 no yes unassembled [7-28] [1.4] [0.063] [0.047] [0.625] [0.500] 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) A Slot Length (mm [in]) 274 Dimensions Shaft Seal 4 Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 75 Taper End Resistance at CW, Max. (Ohm) 385500M9303 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] B D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 22,23 Max. [0.875] 90° Mounting surface 0,635 [0.025] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 1 Left 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Table 385-F Order Guide B C D Slot Thickness (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) Dimensional Drawings (For reference only: mm [in].) C D 2,77 [0.109] A Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B 3,18 [0.125] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 40 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 2X 20° Honeywell Sensing and Control 12,87 [0.546] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] Mounting Hardware 1-4 12 1,60 1,19 15,88 12,7 no no unassembled [7-28] [1.4] [0.063] [0.047] [0.625] [0.500] 312 S-4 312 14,30 [0.563] RoHS Compliant A Slot Length (mm [in]) Dimensions Shaft Seal Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) Effective Electrical Rotation, Typ. (Degree) 4 Taper End Resistance at CCW, Max. (Ohm) 10 Electrical Rotation, ±3 (Degree) End Resistance at CW, Max. (Ohm) 385500M1654 200 Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-G Order Guide B C D Slot Thickness (mm [in]) Shaft Length (mm [in]) Bushing Length (mm [in]) Mounting Hardware 1-6 24 1,60 1,19 15,88 12,7 yes no unassembled [7-42] [2.8] [0.063] [0.047] [0.625] [0.500] 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] RoHS Compliant A Slot Length (mm [in]) 274 Shaft Seal 4 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Effective Electrical Rotation, Typ. (Degree) 10 Mechanical Rotation (Degree) End Resistance at CCW, Max. (Ohm) 5k Taper End Resistance at CW, Max. (Ohm) 385518M0018 Electrical Rotation, ±3 (Degree) Catalog Listing Resistance Tolerance (±%) Mechanical Resistance (Ohm) Electrical Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] C D 2,77 [0.109] A 3,18 [0.125] 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 22,23Max. [0.875] 90° Mounting surface 0,635 [0.025] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 3X 1,57 [0.062] 1 Left 3,18 Min. [0.125] 3 2 Right Center 2X 20° Table 385-H Order Guide Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 12 1,60 1,19 no [1.4] [0.063] [0.047] 12 1,60 1,19 no [1.4] [0.063] [0.047] RoHS Compliant D Bushing Length (mm [in]) 274 C Shaft Length (mm [in]) 4 B Slot Thickness (mm [in]) 4 A Slot Length (mm [in]) 10 1-4 [7-28] 1-4 312 S-4 312 [7-28] 312 S-4 312 Dimensions Shaft Seal 385000M6960 270 Stop Torque (N m [in-lb]) 274 Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper Effective Electrical Rotation, Typ. (Degree) 10 Electrical Rotation, ±3 (Degree) End Resistance at CCW, Max. (Ohm) 385000M1495 5 M Catalog Listing Resistance (Ohm) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Electrical Mounting Hardware 15,88 9,53 yes unassembled [0.625] [0.375] 22,23 9,53 yes unassembled [0.875] [0.375] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] B D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 [0.250] Locating pin 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 2X 20° Honeywell Sensing and Control 41 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-I Order Guide 385500M0563 1k 10 4 4 274 385500M1231 200 10 4 4 274 385500M1377 500 10 4 4 274 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 22,23 [0.875] 22,23 [0.875] 31,75 [1.25] 22,23 [0.875] 22,23 [0.875] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] 1-4 312 S-4 312 [7-28] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 1,60 no [0.063] 1,60 no [0.063] 1,60 no [0.063] 1,60 no [0.063] 1,60 no [0.063] RoHS Compliant 274 Bushing Length (mm [in]) 4 Shaft Length (mm [in]) 4 D Slot Thickness (mm [in]) 10 C Slot Length (mm [in]) 1k B Shaft Seal 385500M0567 A Stop Torque (N m [in-lb]) 274 Dimensions Operating Torque (mN m [in-oz]) 4 Mechanical Rotation (Degree) 4 Taper Effective Electrical Rotation, Typ. (Degree) 10 Electrical Rotation, ±3 (Degree) End Resistance at CCW, Max. (Ohm) 385500M0297 10 k Catalog Listing Resistance (Ohm) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Electrical no unassembled no unassembled no unassembled no unassembled no unassembled Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] D 2,77 [0.109] A B 3,18 [0.125] Locating pin 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 42 [0.250] 3/8-32 NEF-2A Terminal base Mounting surface 0,635 [0.025] 2X 20° Honeywell Sensing and Control 12,87 [0.546] ø6,35 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center Mounting Hardware 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-J Order Guide 4 274 312 S-4 312 385518M1309 2.5 k 10 4 4 274 312 S-4 312 385518M1813 10 k 10 4 4 274 312 S-4 312 385518M2059 50 k 10 4 4 274 312 S-4 312 Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] 12,7 [0.500] 22,23 [0.875] 12,7 [0.500] 22,23 [0.875] 12,7 [0.500] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 9,53 [0.375] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 12 [1.4] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] 1,60 yes [0.063] Mounting Hardware no unassembled no unassembled no unassembled no unassembled no unassembled Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1,19 [0.047] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] 1-6 [7-42] RoHS Compliant 4 Bushing Length (mm [in]) 10 Shaft Length (mm [in]) 385518M0869 2.5 k D Slot Thickness (mm [in]) 312 S-4 312 C Slot Length (mm [in]) 274 B Shaft Seal 4 A Stop Torque (N m [in-lb]) Effective Electrical Rotation, Typ. (Degree) 4 Dimensions Operating Torque (mN m [in-oz]) End Resistance at CCW, Max. (Ohm) 10 Taper End Resistance at CW, Max. (Ohm) 385518M0106 10 k Catalog Listing Resistance (Ohm) Resistance Tolerance (±%) Mechanical Rotation (Degree) Mechanical Electrical Rotation, ±3 (Degree) Electrical A 3,18 [0.125] 3X 1,57 [0.062] 3X 1,57 [0.062] [0.250] 22,23 Max. [0.875] 90° 3/8-32 NEF-2A Terminal base 3X 2,36 [0.093] 3X 3,15 [0.124] 12,87 [0.546] ø6,35 Locating pin 1 Left Mounting surface 0,635 [0.025] 3,18 Min. [0.125] 3 Right 2 Center 2X 20° Table 385-K Order Guide 312 Z Dimensional Drawings (For reference only: mm [in].) RoHS Compliant 274 D Bushing Length (mm [in]) 10 C Shaft Length (mm [in]) 10 k B Slot Thickness (mm [in]) Z A Slot Length (mm [in]) 312 Shaft Seal 274 Dimensions Stop Torque (N m [in-lb]) 4 Operating Torque (mN m [in-oz]) Taper 4 Mechanical Rotation (Degree) Electrical Rotation, ±3 (Degree) 20 Effective Electrical Rotation, Typ. (Degree) 385500M9553 1 M End Resistance at CCW, Max. (Ohm) 385000M8686 100 k 10 Mechanical End Resistance at CW, Max. (Ohm) Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical Mounting Hardware 1-4 12 1,60 1,19 22,23 9,53 312 [7-28] [1.4] no [0.063] [0.047] [0.875] [0.375] yes unassembled 1-4 12 1,60 1,19 22,23 9,53 312 [7-28] [1.4] no [0.063] [0.047] [0.875] [0.375] yes unassembled 14,30 [0.563] 2,77 [0.109] Shown with 50% shaft rotation C ø27,79 Max. [1.094] 13,49 [0.531] B D A 3,18 [0.125] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 12,87 [0.546] ø6,35 Locating pin 3X 1,57 [0.062] [0.250] 3/8-32 NEF-2A Terminal base 0,635 [0.025] Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 Right 2 Center 2X 20° Honeywell Sensing and Control 43 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers 50099565 ISSUE A Table 385-L Order Guide RoHS Compliant 312 D Bushing Length (mm [in]) Z C Shaft Length (mm [in]) 312 B Slot Thickness (mm [in]) Taper Mechanical Rotation (Degree) 274 A Slot Length (mm [in]) Electrical Rotation, ±3 (Degree) 10 Dimensions Shaft Seal Effective Electrical Rotation, Typ. (Degree) 2.5 k Stop Torque (N m [in-lb]) End Resistance at CCW, Max. (Ohm) 10 385500M1246 250 k Operating Torque (mN m [in-oz]) End Resistance at CW, Max. (Ohm) Mechanical Resistance Tolerance (±%) Catalog Listing Resistance (Ohm) Electrical 1-4 12 1,60 1,19 22,23 9,53 no no unassembled [7-28] [1.4] [0.063] [0.047] [0.875] [0.375] Dimensional Drawings (For reference only: mm [in].) 14,30 [0.563] Shown with 50% shaft rotation ø27,79 Max. [1.094] 13,49 [0.531] B C D 2,77 [0.109] A 3,18 [0.125] 3X 1,57 [0.062] 3X 2,36 [0.093] 3X 3,15 [0.124] 3X 1,57 [0.062] 44 ø6,35 Locating pin 3/8-32 NEF-2A 0,635 [0.025] 2X 20° Honeywell Sensing and Control 12,87 [0.546] [0.250] Terminal base Mounting Hardware Mounting surface 3,18 Min. [0.125] 22,23 Max. [0.875] 90° 1 Left 3 2 Right Center 380, RV4, 485, 53C, 385 Series 2 W Conductive Plastic Potentiometers ISSUE A 50099565 WARRANTY/REMEDY WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: E-mail: info.sc@honeywell.com Internet: sensing.honeywell.com Phone and Fax: USA/Canada +1-800-537-6945 International +1-815-235-6847; +1-815-235-6545 Fax Sensing and Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 honeywell.com 50099565-A-EN  IL50 GLO  Printed in USA. October 2014 © 2014 Honeywell International Inc. All rights reserved.