Manual Switches
Lamps, Soldering Recommendations, Receptacles
AML91 LAMP ORDER GUIDE
Lamp
Type
Industry
Lamp No.
Catalog
Listing
Incandescent
T-1-3/4
wedge base
86
6.3
AML91LA86
73
14.0
AML91LA73
85
28.0
AML91LA85
Voltage
LAMP DATA
The following data was compiled from
manufacturer’s specifications, for reference only.
SOLDERING RECOMMENDATIONS
All terminals are solder plated. Proper soldering and cleaning procedures must be
followed to maintain the reliability of AML
products during installation. An instruction sheet which outlines these procedures is included with AML shipments.
You may also obtain a copy from your
MICRO SWITCH Sales Office. Request
PK 8518.
As a general guide, the following information may be used:
INCANDESCENT LAMPS
Industry
Lamp No.
AML91 Series
Volts
Amps
Watts
MSCP
Life
A/C Volts
86
6.3
5.5
5.0
.200
.185
.177
1.25
1.12
.89
.49
.246
.185
20,000 hours
106,200 hours
290,000 hours
73
14.0
12.0
.080
.077
1.12
1.00
.30
.23
15,000 hours
36,450 hours
85
28.0
24.0
.04
.037
1.12
.89
.30
.177
7,000 hours
41,860 hours
Use a 280°C (538°F) solder iron tip, up to
6 seconds duration, with a 60-40 rosin
core solder. This allows the terminal to
heat quickly on the exterior of the housing
only, and greatly reduces the chance of
flux migrating inside the housing.
Neon Lamps
25,000 hours (half life)
INTEGRAL LEDs
LEDs Furnished
Permanently
Installed in
These Products
Peak Inverse Voltage
w/o Diode
w/Diode
Protection
Protection
Vf
If
VPD
AML12, 15, 16,
22, 25, 26, 42
2.4 V
20 mA
.7 V
5V
34 V
AML45
2.4 V
20 mA
.7 V
4V
33 V
100,000 hours (half life).
LED APPLICATION INFORMATION
For those devices without internal current
limiting resistors, suitable external control
of the LED current must be provided. It is
recommended that a minimum of 5 VDC
open circuit voltage with an appropriate
series resistance be used to drive LED devices. This minimizes the effect of temperature (current variation) on forward voltage of the LED.
Resistor values can be determined by
supply voltage or current for LED:
AML92 SERIES LEDs
RS J
For use with these AML switches and indicators equipped with lamp sockets:
Pushbutton switches: AML11 (Square
Only)*, AML21 (rectangular and square),
and AML31.
Paddle switches: AML31/23/33
Rocker switches: AML14/24/34
Indicators: AML41
* Rectangular solid state with one or two lamp circuits
cannot be used with LED catalog listings ending in
‘‘L’’.
E – Vf
If
AML92 ORDER GUIDE
Quad Chip
Six Chip
Red
LED Color
AML92ERY
AML92ERL
Green
AML92EGY
AML92EGL
Yellow
AML92EYY
AML92EYL
White
—
AML92EWL**
** For use with white or yellow buttons.
OPERATING CHARACTERISTICS
WHERE: RS J Series Resistance
E J Supply Voltage
Vf J Forward Voltage of LED
If J Circuit Current
If a diode is added in series for reverse
polarity protection then:
RS J
Type
VF Fwd. Voltage (typ.)
Yellow
Green
Red
White
IF Fwd.
Current
VR Rev.
Voltage
Quad Chip
8.6
8.6
7.8
—
15 mA
16 V
Six Chip
4V
4V
4V
4V
50 mA
5.6 V
E – Vf – VPD
If
WHERE: VPD Forward Voltage of
Protection Diode
TEMPERATURE RANGE
(Quad Chip or Six Chip)
Operating: –20 to 60°C (–4 to 140°F)
Storage: –30 to 100°C (–22 to 212°F)
58
Honeywell 1 Sensing and Control 1 1-800-537-6945 USA 1 F1-815-235-6847 International 1 1-800-737-3360 Canada
很抱歉,暂时无法提供与“AML91LA85”相匹配的价格&库存,您可以联系我们找货
免费人工找货