F58000138

APPLICATIONS LT • HALF INCH DIAMETER LINEAR POSITION TRANSDUCER The Model LT is a small diameter linear position transducer that is rugged enough to withstand the hostile environment of the factory. Using a proprietary dual wiper and the MystR® conductive plastic film the LT provides usable output at high vibration levels for long periods. The LT transducers use precious metal wipers to further enhance reliability. The LT can be provided with shaft seals for spray of hose. Intrinsically Safe for Class I, II, and III Division 1, Groups A, B, C, D, E, F and G for Hazardous (indoor/outdoor) NEMA 4 locations. V max = 30 V, I max = 100 mA, Ci = 0, uF, Li, = 0 mH. • • • • • • • • BENEFIT 0.50 inch diameter Dual wiper design Extruded wiper block guides MystR® plastic element Anodized extruded aluminum housing Stainless steel shaft Precious metal contact Absolute continuous measurement • • • • • • • • Fits into tight spaces, clamps easily to cylinders Improves shock and vibration performance Smooth quiet motion; extends operating life Tested up to one billion operations Tolerates clamping loads Full performance in hostile environments Low noise level over entire life Accurate position at power up HOW TO ORDER LTS 05 N 05K F 5 C Model Termination LTS = Standard LTW = Water Resistant Electrical Travel* Unit of Measure C = Cable Shaft 5 = 4-40 Thread 01 02 03 04 05 = = = = = 1000 2000 3000 4000 5000 06 07 08 09 10 = = = = = 6000 7000 8000 9000 10000 Linearity B = 0.1% F = 1.0% 1000, 2000, 3000, 4000, 5000, 6000, 7000, 8000, 9000, 10000 N = Inches Note: Not all combinations are available. Minimum quantity orders apply. Contact the factory for more details. * Note: The Electrical Travel correlates to the Total Resistance (Ohms). Total Resistance* MODEL LT FEATURES HALF INCH DIAMETER LINEAR POSITION TRANSDUCER • MEDICAL EQUIPMENT • HOSPITAL BEDS • LINEAR ACTUATORS • ANIMATED CHARACTERS • GAUGING • WOODWORKING GUIDES • FLUID FLOW METERS • SEISMOLOGY • SEMI CONDUCTOR PROCESSING MODELS LT • HALF INCH DIAMETER LINEAR POSITION TRANSDUCER TECHNICAL SPECIFICATIONS MECHANICAL Total Mechanical Travel 1.05 to 10.05 in. (min) 26.7 to 255.3 mm (min) Starting Force xx.xx = inches (xx.x) = mm 1.0 oz (max)* Shock 50 g 11 ms half sine Vibration Life DIMENSIONS Housing Length 'X' (Electrical Travel +1.50 [38.1]) #28 Jacketed Cable 6.0 (152.4) Long Min 20 g rms 5 Hz to 2 KHz 1" [25.4] (Retracted) ¯1/8" [3.17] One Billion dither operations ¯1/2" [12.7] ELECTRICAL Electrical Travel (1 inch increments) 1 to 10 in. (25.4 to 254.0 mm) Total Resistance 1000 Ohms per inch electrical travel Operating Temperature Shaft Extended -40° to 80°C (-40° to 176°F) Resolution (Red) V-in (Black) Ground ±20% Resistance Tolerance Insulation Resistance #4-40 UNC-2A Thd x .50 (12.7) Long ±1.0% Independent Linearity ** (Brown) V-out Infinite Connect to High Impedance Circuit 500 M Ohms @ 500 Vdc Dielectric Strength 1000 V rms Model Electrical Travel in inches Total Resistance Ohms Housing Length ‘X’ in inches Weight in grams LTS01 or LTW01 1.0 1000 2.5 20 LTS02 or LTW02 2.0 2000 3.5 26 LTS03 or LTW03 3.0 3000 4.5 31 LTS04 or LTW04 4.0 4000 5.5 43 LTS05 or LTW05 5.0 5000 6.5 45 Caution: Do not test on an Ohm Meter on the Rx 1 scale or other current devices. LTS06 or LTW06 6.0 6000 7.5 48 Caution: Excessive Wiper Current can cause Output errors or damage. LTS07 or LTW07 7.0 7000 8.5 51 Caution: Zero shaft side load is recommended to achieve maximum life. LTS08 or LTW08 8.0 8000 9.5 57 LTS09 or LTW09 9.0 9000 10.5 62 LTS10 or LTW10 10.0 10000 11.5 68 Max. Applied Voltage Backlash 30 Vdc 0.0002 in. max