HFD3022-002

HFD3022-002/XXX Silicon PIN Photodiode FEATURES • Low capacitance • High speed: t² = 30 ns max. @ 5 V • Housing electrically isolated • Wave solderable • Mounting options SMA single hole ST single hole SMA PCB ST PCB SMA 4 hole DESCRIPTION The HFD3022-002/XXX PIN Photodiode is designed for high speed use in fiber optic receivers. It has a large area detector, providing efficient response to 50 - 1000 mm diameter fibers at wavelengths of 750 to 950 nanometers. The HFD3022-002/XXX is comprised of an HFD3022 PIN photodiode which is mounted in a fiber optic connector which aligns the component's optical axis with the axis of the optical fiber. The HFD3022-002/XXXs case is electrically isolated from the anode and cathode terminals to enhance the EMI/RFI shielding which increases the sensitivity and speed. The housing acts as a shield for the PIN photodiode component. 466 h Honeywell reserves the right to make changes in order to improve design and supply the best products possible. HFD3022-002/XXX Silicon PIN Photodiode ELECTRO-OPTICAL CHARACTERISTICS (TÙ = 25¡C unless otherwise stated) PARAMETER SYMBOL Peak Response Wavelength Flux Responsivity [À] MIN æÎ R I° Báß C tß Field of View FoV MAX 850 0.45 Dark Leakage Current Reverse Breakdown Voltage Package Capacitance Rise Time 10-90% TYP 110 0.58 0.58 0.52 0.25 0.05 250 2.1 17 5 1 110 UNITS nm A/W 2 nA V pF ns 30 10 TEST CONDITIONS æ = 850 nm 50 µm core fiber, 0.20 µA 100 µm core fiber, 0.28 µA 200 µm core fiber, 0.40 µA 1000 µm core fiber, 0.53 µA Vß = 5 V Iß = 10 µA Vß = 5 V, f = 1 MHz Vß = 5 V Vß = 15 V Vß = 90 V Degrees Notes 1. Responsivity is measured with a fiber optic cable centered on the mechanical axis, using an 850 nm HFE4000 LED as the optical source to the fiber. The fiber length is nominally 3 meters. ABSOLUTE MAXIMUM RATINGS (Tcase = 25¡C unless otherwise noted) Storage temperature -40 to +100¡C Operating temperature -40 to +100¡C Lead solder temperature 240¡C for 3 min, 260¡C for 10 s Reverse voltage 110 V Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Honeywell reserves the right to make changes in order to improve design and supply the best products possible. h 467 HFD3022-002/XXX Silicon PIN Photodiode ORDER GUIDE Description Catalog Listing Standard silicon PIN photodiode HFD3022-002/XXX MOUNTING OPTIONS Substitute XXX with one of the following 3 letter combinations - AAA SMA single hole - BAA ST single hole - ABA SMA PCB - BBA ST PCB - ADA SMA 4 hole Dimensions on page 441 FIBER INTERFACE Honeywell detectors are designed to interface with multimode fibers with sizes (core/cladding diameters) ranging from 50/125 to 200/230 microns. Honeywell performs final tests using 100/140 micron core fiber. The fiber chosen by the end user will depend upon a number of application issues (distance, link budget, cable attenuation, splice attenuation, and safety margin). The 50/125 and 62.5/125 micron fibers have the advantages of high bandwidth and low cost, making them ideal for higher bandwidth installations. The use of 100/140 and 200/230 micron core fibers results in greater power being coupled by the transmitter, making it easier to splice or connect in bulkhead areas. Optical cables can be purchased from a number of sources. CAUTION The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. Fig. 1 Rise/Fall Time vs Reverse Bias Voltage FIBER033.GRA Fig. 2 Package Capacitance vs Reverse Bias Voltage FIBER051.GR 468 h Honeywell reserves the right to make changes in order to improve design and supply the best products possible. HFD3022-002/XXX Silicon PIN Photodiode Fig. 3 Spectral Responsivity Fig. 4 Dark Leakage Current vs Temperature FIBER101.GRA Fig. 5 FIBER036.GR Angular Response FIBER053.GRA Honeywell reserves the right to make changes in order to improve design and supply the best products possible. h 469 European Connectorized Receivers Honeywell receiver components are available in the following connector styles. Each style has a three-digit reference used in the order guides. SMA SINGLE HOLE MOUNTING (REF.: AAA) ST SINGLE HOLE MOUNTING (REF.: BAA) SMA PCB MOUNTING (REF.: ABA) Honeywell Optoelectronics reserves the right to make changes at any time in order to improve design and supply the best products possible. 441 European Connectorized Receivers ST PCB MOUNTING (REF.: BBA) SMA 4 HOLE MOUNTING (REF.: ADA) 442 Honeywell Optoelectronics reserves the right to make changes at any time in order to improve design and supply the best products possible.