HIH-4602-L-CP

HIH-4602-L Series Humidity Sensors DESCRIPTION A typical current draw of only 200 µA allows use in battery- HIH-4602-L Series Relative Humidity (RH) sensors are powered systems. designed to deliver RH sensing in a rugged, low-cost slotted TO-5 can. HIH-4602-L-CP sensors include a calibration and data printout to allow individually matched downstream electronics and The laser-trimmed, thermoset polymer capacitive sensing ±3.5 %RH total accuracy. elements have on-chip integrated signal conditioning, helping to reduce product development times. FEATURES POTENTIAL APPLICATIONS • Near linear voltage output vs %RH • Refrigeration • Laser-trimmed interchangeability • Drying • Enhanced accuracy, fast response • Meteorology • Chemically resistant • Battery-powered systems • Stable, low drift performance • OEM (Original Equipment Manufacturer) assemblies • Built-in static protection • TO-5 can HIH-4602-L Series Table 1. Performance Specifications (At 5 Vdc supply and 25 ºC [77 ºF] unless otherwise noted.) Parameter Minimum Interchangeability (first order curve) 0% RH to 59% RH 60% RH to 100% RH Accuracy (best fit straight line) Hysterisis Repeatability Settling time Response time (1/e in slow moving air) Stability (at 50% RH in one year) Voltage supply Current supply Output voltage temp. coefficient at 50% RH, 5 V Voltage output (1st order curve fit) – – – – -5 – 5 % RH -8 – 8 % RH -3.5 – +3.5 % RH – 3 – % RH – ±0.5 – % RH – – 70 ms – 30 – s – 1.2 – % RH 4 – 5.8 Vdc – 200 500 µA – -4 – mV/°C VOUT = (VSUPPLY)(0.0062(sensor RH) + 0.16), typical at 25 °C Temperature compensation Operating temperature Operating humidity Storage temperature Storage humidity Specific Notes: 1. Applies to HIH-4602-L-CP only. 2. Device is calibrated at 5 Vdc and 25 ºC. 3. Non-condensing environment. Ratiometric response for 0% RH to 100% RH VOUT 2 HIH-4602-L-CP 92 030996M 337313 0.958 V 3.268 V 0.958 V 30.680 mV/%RH (VOUT - zero offset)/slope (VOUT - 0.958)/0.0307 VSUPPLY (0.1915 to 0.8130) www.honeywell.com/sensing Maximum Unit Specific Note – – – 1 – – – – – – – – 2 True RH = (sensor RH)/(1.0546-0.00216T), T in °C -40[-40] See Figure 1. 85[185] °C[°F] – 0 See Figure 1. 100 % RH 3 -40[-40] See Figure 2. 125[257] °C[°F] – See Figure 2. % RH 3 General Notes: • Sensor is ratiometric to supply voltage. • Extended exposure to >90% RH causes a reversible shift of 3% RH. • Sensor is light sensitive. For best performance, shield sensor from bright light. Factory Calibration Data HIH-4602-L-CP Sensors include a calibration and data printout. See Table 2. Table 2. Example Data Printout Model Channel Wafer MRP Calculated values at 5 V VOUT at 0% RH VOUT at 75.3% RH Linear output for 3.5% RH accuracy at 25 °C Zero offset Slope RH Typical Humidity Sensors Figure 1. Operating Environment (Non-condensing environment.) Figure 2. Storage Environment (Non-condensing environment.) Honeywell Sensing and Control 3 HIH-4602-L Series Figure 3. Typical Output Voltage vs Relative Humidity (At 5 V and 25 °C.) 4 3.5 Output Voltage (Vdc) 3 2.5 Sensor Response Sensor Response Best Linear Fit 2 1.5 1 0.5 0 20 40 60 80 100 Relative Humidity (%RH) Figure 4. Typical Output Voltage (BFSL) vs Relative Humidity (At 0 ºC, 70 ºC and 5 V.) 4.5 4 3.5 Output Voltage (Vdc) 3 2.5 0C 70 C 2 1.5 1 0.5 0 0 10 20 30 40 50 60 Relative Humidity (%) 4 www.honeywell.com/sensing 70 80 90 100 Humidity Sensors Figure 5. Mounting Dimensions (For reference only. mm/[in]) 1. Case ground 2. Vdc out 3. (-) Power or ground 4. (+) Vdc supply 5. No connection 6. No connection Figure 6. RH Sensor Construction Figure 7. Typical Application Circuit Sensor construction consists of a planar capacitor with a second polymer layer to protect against most dirt/dust particles, oils and other hazards. Honeywell Sensing and Control 5 Order Guide Catalog Listing HIH-4602-L HIH-4602-LP Description Relative humidity sensor in TO-5 can Relative humidity sensor in TO-5 can with calibration and data printout ADDITIONAL HUMIDITY SENSOR INFORMATION See the following associated literature at www.honeywell.com/sensing: • Product installation instructions • Application sheets: – Humidity Sensor Performance Characteristics – Humidity Sensor Theory and Behavior – Humidity Sensor Moisture and Psychrometrics – Thermoset Polymer-based Capacitive Sensors WARNING WARNING MISUSE OF DOCUMENTATION • The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. • Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. SALES AND SERVICE Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: E-mail: info.sc@honeywell.com Internet: www.honeywell.com/sensing Phone and Fax: Asia Pacific +65 6355-2828 +65 6445-3033 Fax Europe +44 (0) 1698 481481 +44 (0) 1698 481676 Fax Latin America +1-305-805-8188 +1-305-883-8257 Fax USA/Canada +1-800-537-6945 +1-815-235-6847 +1-815-235-6545 Fax Automation and Control Solutions Sensing and Control Honeywell 1985 Douglas Drive North Minneapolis, MN 55422 www.honeywell.com/sensing 009043-1-EN IL50 GLO Printed in USA December 2008 © 2008 Honeywell International Inc. All rights reserved.