HRF-SW1031

HRF-SW1031 Preliminary SP6T Absorptive RF Switch Features • • • • • • • • High Isolation Of > 40 dB @ 2 GHz Low Insertion Loss Of 1.9 dB @ 2 GHz DC To 3000 MHz Operating Frequency Integrated CMOS Control Logic Integrated ESD Protection on Digital I/O Single Positive Supply Voltage TM Ultra Small LPCC Packaging Impedance matched to 75 Ohm systems Product Description The Honeywell HRF-SW1031 is a high performance single pole six throw (SP6T) absorptive RF switch that is ideal for use in wireless basestation and handset applications that require minimum power and minimum insertion loss. The HRF-SW1031 is manufactured with Honeywell's patented Silicon On Insulator (SOI) CMOS technology, which provides the performance of GaAs with the economy and integration capabilities of conventional CMOS technology. HRF-SW1031 in LPCC™ Package RF Electrical Specifications @ + 25oC Results @ Vdd = 5.0 +/- 10%, Vss = 0 unless otherwise stated, Z0 = 75 ohms Parameter Insertion Loss T est Condition Frequency DC – 1.0 GHz 2.0 GHz 3.0 GHz DC – 1.0 GHz 2.0 GHz 3.0 GHz DC – 0.5 GHz 0.5 – 2.0 GHz 2.0 – 3.0 GHz Minimum T ypical 1.7 1.9 2.4 54 41 33 1.1:1 1.4:1 1.9:1 19 28 35 >35 10 20 10 Maximum Units dB dB dB dB dB dB Ratio Ratio Ratio dBm dBm dBm dBm nS nS mV Isolation VSWR* 2.1:1 1dB Compression Input Power Vss=Gnd Vss= -3 Two-Tone Inputs Up To + 5 dBm Vss= Gnd Vss= -3 10% To 90% 50% Cntl To 90%/10%Rf In-Band 1.0 GHz 1.0 GHz 2.0 GHz 2.0 GHz Input IP3 Trise, Tfall* Ton, Toff Transients *By design _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 1 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1031 Preliminary DC Electrical Specifications @ + 25 C Parameter Single VDD Supply Voltage CMOS Logic Level (0) CMOS Logic Level (1) Input Leakage Current *Note, performance curves are for Vdd = +5.0 +/- 10% Minimum 3.3* 0 VDD – 0.8 T ypical 5.0 Maximum 5.5 0.8 VDD 10 Units V V V uA o Absolute Maximum Ratings1 Parameter VDD Vin Digital Logic 0 Vin Digital Logic 1 Maximum Input Power ESD Voltage Operating Temperature Range Storage Temperature Range Absolute Maximum +6.0 Vss - 0.6 Vdd + 0.6 > 35 400 +85 +125 Units V V V dBm V Degrees C Degrees C (Note 1) Operation beyond any of these parameters may cause permanent damage. Latch-Up: Unlike conventional CMOS RF switches, Honeywell's HRF-SW1031 is immune to latch-up. ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be taken to ensure that the Absolute Maximum Ratings are not exceeded. Package Outline Drawing Bottom View, 24 Pin 4X4 mm LPCCTM Package ASAT LPCC Marketing Outline Dwg. # GMJ00004 For more information see http://www.asat.com _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 2 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1031 Preliminary Truth Table C2 0 0 0 1 1 1 C1 0 1 1 0 0 1 C0 1 0 1 0 1 0 RF Output 1 RFINPUT RF Output 2 RFINPUT RFINPUT RFINPUT RFINPUT RFINPUT RF Output 3 RF Output 4 RF Output 5 RF Output 6 "0" = CMOS Low, "1” = CMOS High Note: For codes 000 and 111 all outputs are in the terminated isolation state. Pin Configuration Pin 1 2 3 4 5 6 7 8 9 10 11 12 Function GROUND GROUND RFOUTPUT5 GROUND GROUND RFOUTPUT4 VDD C2 C1 C0 VSS RFOUTPUT3 Pin 13 14 15 16 17 18 19 20 21 22 23 24 Function GROUND DIGITAL GROUND RFOUTPUT2 GROUND GROUND RFOUTPUT1 GROUND GROUND RFINPUT GROUND GROUND RFOUTPUT6 Evaluation Circuit Board Connections RF Out6 RF Input HRF-SW1030 Honeywell RF Out5 RF Out1 HRF-SW1031 Evaluation Board Top View RF Out4 RF Out2 Gnd VDD C2 C1 C0 VSS Digital Gnd RF Out3 “0” = CMOS Low, “1” = CMOS High _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 3 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 Note: HRF-SW1031 is the Z0 = 75 ohm version of the SW1030 evaluation board. HRF-SW1031 Preliminary Performance Curves Insertion Loss SW1031 Insertion Loss vs Frequency 0.00 -0.50 Inserion Loss (dB) -1.00 -1.50 -2.00 dB(S(2,1))[0,::] -2.50 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) Isolation SW1031 Isolation Vs Frequency 0.00 -10.00 -20.00 -30.00 Isolation (dB) -40.00 -50.00 -60.00 -70.00 -80.00 -90.00 dB(S(3,1))[0,::] -100.00 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 4 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1031 Preliminary Return Loss SW1031 Return Loss Vs Frequency 0.00 -2.00 -4.00 -6.00 -8.00 S11 -10.00 -12.00 -14.00 -16.00 -18.00 -20.00 0 0.5 1 1.5 2 2.5 3 dB(S(1,1))[0,::] dB(S(2,2))[0,::] dB(S(3,3))[0,::] S22 Return Loss (dB) S33 Frequency (GHz) P1dB SW1031 P1dB Vs Frequency 35 30 Outut Power(dBm) 25 20 15 10 PoutLinear Pout 1GHz Pout 2GHz Pout 3 GHz 5 0 0 5 10 15 20 25 30 35 Input Power (dBm) _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 5 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1031 Preliminary Evaluation Circuit Board Honeywell's evaluation board provides an easy to use method of evaluating the RF performance of our switch. Simply connect power, DC and RF signals to be measuring switch performance in less than 10 minutes. HRF-SW1031 Evaluation Board Evaluation Circuit Board Layout Design Details Item PCB Switch Chip Capacitor RF Connector DC Pin Description Impedance Matched Multi-Layer FR4 HRF-SW1031 RF Switch Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector Mil-Max Model 800-10-064-10-001 Header Pins Ordering Information Ordering Number HRF-SW1031-B HRF-SW1031-TR HRF-SW1031-E (Note 2) Contact Honeywell for details Product Delivered In Chip Tubes 2 Delivered On Tape And Reel Engineering Evaluation Board LPCC TM is a registered Trademark of ASAT Ltd. Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1031W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 6 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295