LZZ1D

PK 88142 MODULAR PARTS complete switch = operating head + base receptacle + switch body Complete Switch LZA1 LZC1 LZD1 LZV1 LZE1 LZF1 LZG1 LZW1 LZH1 LZL1-6C Operating Head Only Side Rotary Top Plain Plunger Top Roller Plunger, roller parallel to mounting surface Adjustable Top Plunger Side Plain Plunger Side Roller Plunger, roller parallel to mounting surface Side Roller Plunger, roller perpendicular to mounting surface Adjustable Side Plunger Side Palm Plunger Side Lever with lever bracket LZZ1A LZZ1C LZZ1D LZZ1V LZZ1E LZZ1F LZZ1G LZZ1W LZZ1H LZZ1M-6C REPLACEMENT LEVERS FOR SIDE ROTARY Body with basic switch (Buna-N seal) Body with basic switch (Fluorocarbon seal) Base Receptacle Adapter Plate Lever bracket (without lever) Lever arm for above Nylon roller Steel roller Boot for plungers Plastic wobble stick Spring wire wobble stick 1¼ inch buttons Black Red Yellow 1½ inch buttons Black Red Yellow Catalog Listing LZZ21 LZZ22 LZZ41 LZZ42 LZZ43 LZZ56C LZZ56D LZZ44 LZZ57B LZZ57M PWMZ22 PWMZ23 PWMZ25 PWMZ32 PWMZ33 PWMZ35 MICRO SWITCH WORLDWIDE SALES AND SERVICE MICRO SWITCH serves its customer through a worldwide network of sales offices and distributors. For application assistance, pricing or name of nearest Authorized Distributor, contact a nearby MICRO SWITCH sales office. Or, write MICRO SWITCH, Freeport, Illinois 61032; phone 815/235-6600. While we provide application assistance on MICRO SWITCH products, personally and through our literature, it is up to the customer to determine the suitability of the product in his application. PK 8814 2 880 PRINTED IN USA a Honeywell Division Installation and adjusting instructions LZ metal-enclosed switches Description Description Sensing & Control To order replacement levers, order the same part number as that which is metal stamped on either the lever or lever hub. For other variations of levers, refer to Heavy Duty LS in Catalog 40. MOUNTING LZ may be mounted without unplugging the body from the base receptacle. Use two M5 or #10 screws that are at least 32mm (1.25 in.) long. A third mounting screw may be used by removing the knockout in the lower right corner. Refer to Figure 1. WIRING Up to 3mm or AWG12 wire may be used for wiring to the self-lifting pressure plate-type screw terminals. Maximum width of spade connectors or diameter of ring connectors is 8mm (.312 in.). A ground terminal, which is colored green for easy identification, also has self-lifting pressure plate-type construction (refer to Figure 1.). After wiring, screws in the ing. Also plug ensure proper securely tighten the captive plug-in unit for effective sealconduit opening with sealant to sealing. ADJUSTMENT INSTRUCTIONS Actuator Head All LZ actuator heads can be positioned in any of four directions. Loosen the four captive head screws, place the head in the desired position, and securely tighten the screws. Refer to Figure 2. Top Roller Plunger Position the top roller plunger in the desired plane by locating the head as outlined under Actuator Head. POSITIONING LEVER OF ROTARY TYPE The lever on rotary switches is adjustable to any angular position through 360°. Levers are reversible, they can also be shifted axially through approximately 3,2mm (.125 in.) on the shaft. To adjust, or to assemble to switch, loosen the screw with a 9/64 hexagon key wrench, move the lever to the desired position, and securely tighten the screw. The lever should be tightened until the "teller tab" can no longer be moved by hand. Hex key wrenches are provided in adjusting tool set LSZ4005. PK 88142 PK 88142 SIDE ROTARY TYPE CHANGING ACTUATION DIRECTION ON ROTARY TYPE Rotary switches may be adjusted to operate clockwise, counterclockwise, or both. Instructions are cast into the head (Figure 4). Follow these steps: 1. Loosen the four captive head screws and remove head from switch housing. 2. Switches are assembled with the plunger set for both way operation. (See drawing Figure 4.) Both way actuation: plunger point in twelve o'clock position (towards the actuator). To change mode of operation pull the spring loaded plunger outward with pliers to the stop. With plunger, pulled turn the point in the direction of operation required. Clockwise actuation only: turn clockwise to three o'clock position. Counterclockwise actuation only: turn counterclockwise to nine o'clock position. 3. Release plunger, it will snap into the head into a locked position. 4 . Replace operating head on switch housing and securely tighten screws. 5 . Check for desired operation by actuating switch and listening for "click". PK 88142 SIDE LEVER BRACKET TYPE POSITIONING THE SIDE LEVER BRACKET REVERSING THE ROLLER LEVER ARM The side lever bracket can be placed in any of four positions. When combined with the four possible head positions, this makes for 16 possible positions for this type. Remove the lever with a 5/32 inch hexagon key wrench. Loosen three captive bracket screws, place the bracket in the desired position, and securely tighten the screws (refer to Figure 6). Roller arms may be reversed to face the roller to the inside or outside of the arm (refer to Figure 7). It is recommended that the lever of side lever bracket forms be adjusted within the parameters shown in Figure 7. Use a 5/32 hexagon key wrench. HEX HEAD SCREWS If you prefer to loosen and tighten the lever with a pliers or a screwdriver, a packet of 50 hex head screws, with screwdriver slot, is available separately (catalog listing 15PA164-LS) to replace the allen head screw furnished with the lever. Adjusting tool set LSZ4005 consists of one special 3/32 inch open wrench and necessary hexagon key wrenches to adjust all types of levers. WOBBLE STICK ACTUATOR TYPE REPLACING THE WOBBLE STICK To remove a wobble stick, firmly grasp the wobble stick with a pair of pliers at the base of the wobble stick. (Figure 8, View A.) Turn the wobble stick counterclockwise to unscrew it. To attach a wobble stick, start threading the actuator to the head by hand. Then firmly grasp the wobble stick with a pair of pliers as shown in Figure 8, View B. Turn the wobble stick clockwise to within 1/8 inch of the end of the threads.