RPNS090AC1A21X

RPN Series Hall-Effect Rotary Position Sensors DESCRIPTION RPN Series Rotary Position Sensors use a magnetically biased, Hall-effect integrated circuit (IC) to sense rotary movement of the actuator shaft over a set operating range. Rotation of the actuator shaft changes the IC’s position relative to the magnets. The resulting flux density change is converted to a linear output. The IC, together with conditioning and protection circuitry, and two permanent magnets, is sealed in a rugged package of IP67 or greater for durability in most harsh environments. Five different supply voltages and eight different output configurations, in either mA or Vdc, improve compatibility with a variety of control systems. Two versions provide dual outputs for use where an additional output may be desired where redundancy and backup is needed. Another potential application includes using one output for an indicator and the second for the control system. Lever versions are available. The easy-to-mount sensor has a mounting flange with two round or oval mounting holes. All products have AMP or Deutsch receptacles. Solid-state Hall-effect technology provides non-contact operation, long service life, low torque actuation and reduced wear-out mechanisms. Eight operating ranges (50°, 60°, 70°, 90°, 120°, 180°, 270° and 360°) are tolerant to over travel and allow use in most common applications. FEATURES • Solid-state Hall-effect technology • Eight operating ranges, up to 360° • Variety of supply voltages and output configurations • Rugged sealed package with integral connector • IP67 or greater • Integrated reverse polarity, short circuit and EMC protection • Single or dual output versions available • Industry-standard termination POTENTIAL APPLICATIONS Position and movement detection of pedals, throttle, gear shift, levers, linkages, suspension and hitches in: • Trucks • Off road vehicles • Industrial vehicles and equipment • Construction vehicles and equipment • Agricultural vehicles and equipment • Cranes RPN Series Table 1. RPNR Redundant (Dual) Output Specifications Characteristic Parameter Operating ranges available 50° (±25°), 90° (±45°) Output available 50° (±25°): Channel 1: 4 mA (left), 20 mA (right); Channel 2: 0.25 Vdc (left), 4.75 Vdc (right) 90° (±45°): Channel 1: 0.25 Vdc (left), 4.75 Vdc (right); Channel 2: 4.75 Vdc (left), 0.25 Vdc (right) Supply voltage range(s) 50° (±25°): Channel 1: 8.5 Vdc; Channel 2: 5 Vdc available 90° (±45°): Channel 1: 10 Vdc to 30 Vdc; Channel 2: 10 Vdc to 30 Vdc Current consumption 20 mA max. Output signal delay 3 ms approx. Accuracy ±1.6% Hysteresis none Linearity RPNR050SDMEC3A21X ±0.35° RPNR090KAAA3A11X ±0.6° Reverse polarity protection yes Operating and storage -40 °C to 125 °C [-40 °F to 257 °F] temperature range EMC 200 V/m ISO 11452-3 6 Expected life 30x10 cycles Protection class IP69K DIN 40050 Housing material PA66 plastic Shaft material stainless steel Termination AMP 1-1419168-1 Mechanical end stop no Table 2. RPNS Single Output Specifications Characteristic Operating ranges available Outputs available Supply voltage range(s) available Current consumption (maximum) Output signal delay (approx) Reverse polarity protection EMC Operating and storage temperature range Protection class Accuracy Hysteresis Linearity RPNS050BB1A21X, RPNS050FA1A21X RPNS060AC1A21X RPNS070DD1A21X All other listings RPNS120AA1A21X Housing material Shaft material Expected life Termination Mechanical end stop 2 www.honeywell.com/sensing Parameter 50° (±25°), 60° (±30°), 70° (±35°), 90° (±45°), 120° (±60°), 180° (±90°), 270° (±135°), 360° (±180°) 0.25 Vdc (left), 4.75 Vdc (right) 4 mA (left), 20 mA (right) 0.5 Vdc (left), 4.5 Vdc (right) 20 mA (left), 4 mA (right) 1 Vdc (left), 9 Vdc (right) 3 Vdc (left), 5 Vdc (right) 4.5 Vdc (left), 0.5 Vdc (right) 4.75 Vdc (left), 0.25 Vdc (right) 5 Vdc, 8 Vdc to 30 Vdc, 10 Vdc to 30 Vdc 20 mA 3 ms yes 200 V/m ISO 11452-3 -40 °C to 125 °C [-40 °F to 257 °F] IP67 DIN 40050 ±1.6% none ±0.35° ±0.6 ±1° ±2° ±5° PA66 plastic stainless steel 6 30x10 cycles AMP Superseal 282087-1, Deutsch DT04-3P no Hall-Effect Rotary Position Sensors Figure 1. RPNR Redundant (Dual) Output Versions (For Reference Only: mm/[in].) RPNR050DMEC3A21X RPNR090KAAA3A11X Figure 2. RPNS Single Output Versions (For Reference Only: mm/[in].) RPNS050BB1A21X RPNS050FA1A21X 3 Vdc L Receptacle: AMP Superseal 282087-1 Mating Connector: AMP Superseal 282103 4 Vdc 50° 5 Vdc R 52 [2.05] 37,7 [1.48] 4,2 [0.17] 20° 50 [1,97] 27,7 [1.09] Pinout 1 = Ground 2 = 10 Vdc to 30 Vdc Supply 3 = 3 Vdc to 5 Vdc Output Characteristic Curve 3 63 [2.48] 2 5 24,8 [0.98] 4,12 [0.16] 3 Ø6 [0.24] 25 RPNS060AC1A21X 0 Angle (°) 1 5 [0.20] 25 14 [0.55] 8,3 [0.33] 4,6 [0.18] Ø2 [0.08] Ø20 [0.79] RPNS070DD1A21X Honeywell Sensing and Control 3 Figure 2. RPNS Single Output Versions (Continued) RPNS090AA2A11X RPNS090AC1A21X RPNS090CA1A11X RPNS090DD2A21X WW/YY 248607 Output (Vdc) RPNS090AC1A21X Output (Vdc) 260121 WW/YY RPNS090AA1B11A RPNS090AA1B11A RPNS090AA1A11X 12 mA 90° Receptacle: Deutsch DT04-3P Mating Connector: Deutsch DT06-3S 20 mA R 4 mA L WW/YY 37,7 [1.48] 4,2 [0.17] 20° 248990 RPNS090CA1A11X 52 [2.05] 50 [1,97] 27,7 [1.09] Pinout 1 = Ground 2 = 8 Vdc to 30 Vdc Supply 3 = 4 mA to 20 mA Output Characteristic Curve Output (Vdc) 4,12 [0.16] 4 45 4 www.honeywell.com/sensing 0 Angle (°) 45 Ø6 [0.24] 24,8 [0.98] 2 3 1 5 [0.20] 20 63 [2.48] 14 [0.55] 8,3 [0.33] 4,6 [0.18] Ø2 [0.08] Ø20 [0.79] Figure 2. RPNS Single Output Versions (Continued) RPNS090EA1A11X RPNS090GA1A21X RPNS120AA1A21X RPNS180DA2A11X Receptacle: Deutsch DT04-3P Mating Connector: Deutsch DT06-3S 12 mA 180° WW/YY 20 mA R 4 mA L 248213 RPNS120AA1A21X 52 [2.05] 37,7 [1.48] Ø5.3 [0.20] 50 [1,97] 27,7 [1.09] Pinout 1 = Ground 2 = 10 Vdc to 30 Vdc Supply 3 = 4 mA to 20 mA Output Characteristic Curve Output (Vdc) 4,12 [0.16] 4,6 Ø6 [0.18] [0.24] 0 90 RPNS180HD1B11A 0 Angle (°) 90 24,8 [0.98] 2 3 1 5 [0.20] 20 63 [2.48] 14 [0.55] 8,3 [0.33] Ø2 [0.08] Ø20 [0.79] RPNS270DA1A21X Honeywell Sensing and Control 5 Figure 2. RPNS Single Output Versions (Continued) RPNS360GC1A11X 2.5 Vdc 360° Receptacle: AMP Superseal 282087-1 Mating Connector: AMP Superseal 282103 52 [2.05] 37,7 [1.48] Ø5.3 [0.20] 50 [1,97] 27,7 [1.09] Pinout 1 = Ground 2 = 5 Vdc Supply 3 = 0.5 Vdc to 4.5 Vdc Output 63 [2.48] 0.5 Vdc 4.5 Vdc L R Characteristic Curve 3 4.5 2 1 24,8 [0.98] 5 [0.20] 4,12 [0.16] 0.5 180 6 0 Angle (°) 180 Ø6 [0.24] www.honeywell.com/sensing 14 [0.55] 8,3 [0.33] 4,6 [0.18] Ø2 [0.08] Ø20 [0.79] Order Guide Catalog Listing Output Style redundant RPNR050DMEC3A21X (dual) redundant RPNR090KAAA3A11X (dual) Operating Range Supply Voltage Output Type 50° (±25°) Channel 1: 8.5 Vdc Channel 2: 5 Vdc 90° (±45°) 10 Vdc to 30 Vdc Channel 1: 4 mA (left), 20 mA (right) Channel 2: 0.25 Vdc (left), 4.75 Vdc (right) Channel 1: 0.25 Vdc (left), 4.75 Vdc (right) Channel 2: 4.75 Vdc (left), 0.25 Vdc (right) RPNS050BB1A21X single 50° (±25°) 18 Vdc to 30 Vdc 1 Vdc (left), 9 Vdc (right) RPNS050FA1A21X single 50° (±25°) 10 Vdc to 30 Vdc 3 Vdc (left), 5 Vdc (right) RPNS060AC1A21X single 60° (±30°) 5 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS070DD1A21X single 70° (±35°) 8 Vdc to 30 Vdc 4 mA (left), 20 mA (right) RPNS090AA1A11X single 90° (±45°) 10 Vdc to 30 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS090AA1B11A single 90° (±45°) 10 Vdc to 30 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS090AA2A11X single 90° (±45°) 10 Vdc to 30 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS090AC1A21X single 90° (±45°) 5 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS090 CA1A11X single 90° (±45°) 10 Vdc to 30 Vdc 4.5 Vdc (left), 0.5 Vdc (right) RPNS090DD2A21X single 90° (±45°) 8 Vdc to 30 Vdc 4 mA (left), 20 mA (right) RPNS090EA1A11X single 90° (±45°) 10 Vdc to 30 Vdc 20 mA (left), 4 mA (right) RPNS090GA1A21X single 90° (±45°) 10 Vdc to 30 Vdc 0.5 Vdc (left), 4.5 Vdc (right) RPNS120AA1A21X single 120° (±60°) 10 Vdc to 30 Vdc 4.75 Vdc (left), 0.25 Vdc (right) RPNS180DA2A11X single 180° (±90°) 10 Vdc to 30 Vdc 4 mA (left), 20 mA (right) RPNS180HD1B11A single 180° (±90°) 8 Vdc to 30 Vdc 0.25 Vdc (left), 4.75 Vdc (right) RPNS270DA1A21X single 270° (±135°) 10 Vdc to 30 Vdc RPNS360GC1A11X single 360° (±180°) 5 Vdc 4 mA (left), 20 mA (right) 0.5 Vdc (left), 4.5 Vdc (right) Termination Shaft Mounting Shape Hole AMP 1-1419168flat 1 AMP 1-1419168flat 1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 AMP Superseal round 282087-1 Deutsch DT04-3P AMP Superseal 282087-1 AMP Superseal 282087-1 Deutsch DT04-3P Lever oval none round none oval none oval none oval none oval none round none round 43 mm [1.69 in] flat round none flat oval none flat round none flat oval none round none oval none oval none AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 Deutsch DT04-3P flat AMP Superseal round 282087-1 AMP Superseal flat 282087-1 AMP Superseal flat 282087-1 round none round) 43 mm [1.69 in] oval none round none Honeywell Sensing and Control 7 WARNING WARNING PERSONAL INJURY MISUSE OF DOCUMENTATION DO NOT USE these products as safety or emergency stop • devices or in any other application where failure of the The information presented in this product sheet is for reference only. Do not use this document as a product product could result in personal injury. installation guide. Failure to comply with these instructions could result in death or serious injury. • Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of death or serious injury. defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise SALES AND SERVICE by Honeywell in writing; please refer to your order Honeywell serves its customers through a worldwide network acknowledgement or consult your local sales office for specific of sales offices, representatives and distributors. For warranty details. If warranted goods are returned to Honeywell application assistance, current specifications, pricing or name during the period of coverage, Honeywell will repair or replace, of the nearest Authorized Distributor, contact your local sales at its option, without charge those items it finds defective. The office or: foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of E-mail: info.sc@honeywell.com merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. Internet: www.honeywell.com/sensing Phone and Fax: While we provide application assistance personally, through Asia Pacific +65 6445-3033 Fax our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the +65 6355-2828 Europe +44 (0) 1698 481481 +44 (0) 1698 481676 Fax application. Latin America +1-305-805-8188 Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. +1-305-883-8257 Fax USA/Canada +1-800-537-6945 +1-815-235-6847 +1-815-235-6545 Fax Sensing and Control Honeywell 1985 Douglas Drive North Minneapolis, MN 55422 www.honeywell.com/sensing 005896-2-EN IL50 GLO Printed in USA July 2009 Copyright © 2008 Honeywell International Inc. All rights reserved.