SPS-A180D-HAMS

DESCRIPTION The SMART Position Sensor is one of the most durable, adaptable, and lightweight linear position sensors available in the industry, enabling highly accurate motion control and improving operation efficiency and safety. Its simple, noncontact design eliminates mechanical failure mechanisms, reducing wear and tear, improving reliability and durability, and minimizing downtime. The SMART Position Sensor is a non-contacting sensing solution for absolute position sensing with enhanced accuracy. It senses the position of a magnet relative to the sensor in one of two available sensing ranges: 0 to 100 0 to 180 Why is the SMART Position Sensor smart? SMART means that this is a sensor that can essentially think for itself. SMART Position Sensors provide a self-diagnostics feature and data gathering for enhanced reliability and closed-loop feedback control. VALUE PROPOSITIONS ( = competitive differentiator) They use a patented combination of an ASIC (ApplicationSpecific Integrated Circuit) and an array of MR (magnetoresistive) sensors to accurately and reliably determine the position of a magnet attached to a moving object so that the object’s position can be determined or controlled. The MR array measures the output of the MR sensors mounted along the magnet’s direction of travel. The output and the MR sensor sequence determine the nearest pair of MR sensors to the center of the magnet location. The output of these two MR sensors is then used to determine the position of the magnet between them. With this sensor, Honeywell has utilized MR technology through the ASIC at a level never before accomplished. Other configurations are in development.  Reliable, durable: Non-contact design reduces wear and  tear, improving reliability and durability, minimizing downtime Easy to install: Installation takes 4 steps (1: position device; 2: drill holes 3: mount sensor; 4: locate magnet/connect sensor) vs. up to 14 steps some competitive products require, simplifying installation and reducing set-up costs Rugged: As there are no moving parts within sensor, Honeywell utilizes unique packaging materials that make it resistant to vibration, shock, and extreme temperatures Flexible: Air gap tolerance of 7,8 ±2,5 mm [0.307 ±0.098 in] (100°) and 8,5 ±2,5 mm [0.338 ±0.098 in] (180°) between sensor and magnet expands application use Cost effective: Adaptable, non-contacting design allows customers to eliminate unnecessary connections for installation, thereby reducing installation steps/time and components     Accurate: 100° configuration accurately measures values down to 0.06°while the 180° configuration accurately measures values down to 0.11° Adaptable: Electronics on board allow for flexible packaging and component compatibility with existing systems Lightweight: Lighter in weight than optical encoders Self-diagnostics feature can reduce equipment downtime by providing predictive maintenance input Combined patented MR sensor and ASIC technology provides enhanced differentiation and performance IP67, IP69K sealing allow use in many harsh applications RoHS-compliant materials meet Directive 2002/95/EC  Military Transportation Aerial work lift platform, front end loader and digger/excavator boom position Scissor lift position Refuse truck lift and automatic reach arm position Mobile crane steering Timber harvester/processor equipment cutter arm angle On-board loader weighing system position Industrial Telescoping conveyor elevation Power generation contact angle Rail-road crossing arms position Table 1. Specifications Characteristic Sensing range Resolution Supply voltage Output Supply current Linearity Reverse polarity Sensitivity Measurement frequency Termination Operating temperature Storage temperature Air gap Sealing Shock Vibration Housing material Approvals Mounting: screws recommended torque Material Strength Component Parameter 100 Arc 180 Arc SPS-A100D-HAMS SPS-A100D-VAMS SPS-A180D-HAMS SPS-A180D-VAMS 0 to 100 0 to 180 0.06 0.11 6 Vdc to 24 Vdc 18 Vdc to 40 Vdc 6 Vdc to 24 Vdc 18 Vdc to 40 Vdc 0.5 Vdc to 4.5 Vdc (10% to 90% of 5 Vdc) 45 mA max. ± 0.4% full scale output 26.4 Vdc 40 Vdc 26.4 Vdc 40 Vdc 40 mV/ ± 4% FS 22.22 mV/ ±4% FS 312 Hz typ. 4-pin, M12 connector -40 °C to 85 °C [-40 °F to 185 °F] -40 °C to 150 °C [-40 °F to 302 °F] 7,8 ±2,5 mm [0.307 ±0.098 in] 8,58 ±2,5 mm [0.338 ±0.098 in] IP67, IP69K 50 G half sine wave with 11 ms duration 20 G from 10 Hz to 2000 Hz thermoplastic CE M6 or 1/4-20 6 N m to 8 N m [53.1 in lb to 70.8 in lb] neodymium 10,000 Gauss For more information on these potential applications, please see the application note “SMART Position Sensor, 100 and 180 Arc Configurations”. Medical: Robotically-assisted surgery equipment position Patient bed elevation Aerospace: Ground-based solar panels elevation and azimuth Ground-based satellite dish elevation and azimuth Remote weapon systems elevation Chassis suspension systems position height Military vehicle door position sensor only sensor and magnet actuator magnet actuator only Notes: Tolerance applies for full sense range. Device used to read analog output must have input impedance greater than 1 MOhm. The output voltage outside of the valid measurement range will be indeterminate. Percent linearity is the quotient of the measured output deviation from the best fit line at the measured temperature to the full scale output span. NOTICE Ferrous metal within a 100 mm [3.9 in] radius of the magnet may affect sensor performance. 2 www.honeywell.com/sensing Figure 1. Dimensional Drawings (For reference only: mm) SPS-A100D-HAMS, SPS-A100D-VAMS SPS-A180D-HAMS, SPS-A180D-VAMS A = Cable direction for right angle connector Figure 3. Sensor Output Performance Chart Showing Ideal Outputs (Applies to all catalog listings.) REF POINT "C” REF POINT "B" Figure 2. Pinout 4.75 4.5 4.0 LINEARITY ±0.4% OF FULL SCALE SPA Output Voltage (V) Pin 1 = supply voltage (+) Pin 2 = output Pin 3 = ground (-) Pin 4 = inverted output Note: Only Pin 2 or Pin 4 may be connected at a time. 3.0 PIN 2 NOMINAL SIGNAL OUTPUT CURVE (THROUGH REFERENCE POINTS "A" AND "B") PIN 4 NOMINAL SIGNAL OUTPUT CURVE (THROUGH REFERENCE POINTS "C" AND "D") LINEARITY ±0.4% OF FULL SCALE SPA 2.0 1.0 0.5 0.25 0 REF POINT "A" 0 0 Measurement (°) Angle 100 180 REF POINT "D" Honeywell Sensing and Control 3 Order Guide Catalog Listing SPS-A100D-HAMS SPS-A100D-VAMS SPS-A180D-HAMS SPS-A180D-VAMS Description SMART Position Sensor, 100 arc configuration, 0 to 100 sensing range, 6 Vdc to 24 Vdc supply voltage, 0.5 Vdc to 4.5 Vdc analog output, magnet actuator included SMART Position Sensor, 100 arc configuration, 0 to 100 sensing range, 18 Vdc to 40 Vdc supply voltage, 0.5 Vdc to 4.5 Vdc, analog output, magnet actuator included SMART Position Sensor, 180 arc configuration, 0 to 180 sensing range, 6 Vdc to 24 Vdc supply voltage, 0.5 Vdc to 4.5 Vdc, analog output, magnet actuator included SMART Position Sensor, 180 arc configuration, 0 to 180 sensing range, 18 Vdc to 40 Vdc supply voltage, 0.5 Vdc to 4.5 Vdc, analog output, magnet actuator included WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your orde r acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. Sensing and Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 www.honeywell.com 000732-1-EN IL50 GLO Printed in USA March 2011 Copyright © 2011 Honeywell International Inc. All rights reserved.