SS51T

Interactive Catalog Replaces Catalog Pages Honeywell Sensing and Control has replaced the PDF product catalog with the new Interactive Catalog. The Interactive Catalog is a power search tool that makes it easier to find product information. It includes more installation, application, and technical information than ever before. Sensing and Control Honeywell Inc. 11 West Spring Street Freeport, Illinois 61032 Click this icon to try the new Interactive Catalog. Hall Effect Products Surface Mount Sensors FEATURES/BENEFITS • Wide temperature and voltage ranges for design flexibility and harsh (automotive)environments. • Temperature compensated for consistent operation with low-cost magnets (SS500). • SS5 Package is resistant to thermal and mechanical stress. • SS5 profile is lower than other SOT-89 packages. This allows the customer to reduce the total gap. • Industry standard "gull-wing" design. Less susceptibility to "solder bridging". Allows increased circuit board density. • Bipolar, unipolar and latching magnetics. • Low Gauss versions available for high accuracy or wide gap applications. • SS5 package allows 4-pin package designs TYPICAL APPLICATIONS • Brushless DC motors • Digital current sensor • Anti-skid braking sensor • Piston detection in hydraulic cylinder • Valve position sensing • Cam, lever, shaft position sensing • Tachometer, counter pickup • Push-button sensor • Disk speed, tape rotation, flow rate sensing • Speed sensing - rate, under, over speed • Remote reading sensor • Magnetic card reader SS5 Series SS5 Series Hall effect position sensors are operated by the magnetic field from a permanent magnet or electromagnet. The small SOT89 style package surface mounts on PC boards and flexible circuits. The SS5 uses a industry standard "gull-wing" design which makes it less susceptible to "solder bridging" and allows increased circuit board density. The SS5 series package can accommodate larger IC’s than SS1 and allows for fourpin designs The integrated circuits are designed to provide predictable performance over the full temperature range of -40 to +150°C. Bipolar, unipolar and latching magnetics are available. The SS5 has the same footprint and pinout as the industry standard SOT-89. It will replace Honeywell SS1 Series and any equivalent SOT-89 sensors from other suppliers with minimum or no design changes. On-board regulation provides extremely stable operation over the full supply voltage range of 4.5 to 24 VDC(SS51T) or 3.8 to 30 VDC(SS500). Current consumption is a low 10 mA maximum at 40°C and is typically 7mA or less at room temperature and above. SS5 sensors are capable of continuous 20 mA sinking output, and can withstand temporary current as high as 20 mA maximum (SS51T) or 50 mA maximum (SS500). They can use existing power supply sources in most applications, and can be directly interfaced with many electronic components without buffering or compensation circuitry. SS5 Series sensors are supplied on tape and reel for high-volume, automated pick and place equipment. Each reel contains 1,000 sensors. MICRO SWITCH supplies bar and ring magnets for operating Hall effect sensors. Bar magnets can operate any Hall effect sensor. Ring magnets are magnetized on the outside diameter with alternating North and South poles. They are particularly useful with bipolar sensors and rpm measurement. HONEYWELL Sensing and Control Hall Effect Products Surface Mount Sensors WIRING DIAGRAMS SS5 Series ABSOLUTE MAXIMUM RATINGS Catalog Listing Supply Voltage SS51T -28 to +28 VDC SS500 -1 to +30 VDC Voltage externally applied to output +28 VDC max. (OFF condition only) -0.5 VDC min. (OFF or ON condition) 20 mA max. +30 VDC max. (OFF condition only) -40 to +150°C (-40 to +302°F) -40 to +150°C (-40 to +302°F) -50 to +160°C (-46 to +320°F) -65 to +160°C (-54 to +320°F No limit. Circuit cannot be damaged by magnetic overdrive. No limit. Circuit cannot be damaged by magnetic overdrive. Output ON Current Temperature Limits Operating Storage Magnetic Flux 50 mA max. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. OPERATING CHARACTERISTICS SS51T SS500 Remarks Supply Voltage Current Consumption (Ioff) 4.5 to 24 VDC 10 mA 3.8 to 30 VDC 10 mA Max over temp Output Voltage (operated) 0.4 V 0.4 V Output Current (operated) Output Leakage Current Output Switching Time Rise, 10 to 90% Fall, 90 to 10% 20 mA 10 µA 20mA 10µA 1.5 µs 1.5 µs 1.5 µs 1.5 µs Operating Temperature; °C -40 to +150°C -40 to +150°C 2 Honeywell • Sensing and Control Sinking 20 mA max. VCC = 12 V, RL = 1.6 K Ohm, CL = 20 pF For application help: call 1-800-537-6945 Hall Effect Products Surface Mount Sensors SS5 Series MAGNETIC CHARACTERISTICS Catalog Listing SS51T SS511AT SS513AT SS541AT Magnetic Type Bipolar Bipolar Bipolar Unipolar Magnetic Characteristics (Gauss) SS543AT Unipolar SS549AT Unipolar SS561AT Latching SS566AT Latching -40°C Max. Op. Min. Rel. Min. Dif. 145 -145 40 70 -70 15 140 -140 20 135 20 15 215 80 25 440 210 30 110 -110 50 200 -200 200 0°C Max. Op. Min. Rel. Min. Dif. 145 -145 50 65 -65 15 140 -140 20 117 20 18 190 80 25 400 230 30 90 -90 50 185 -185 200 25°C Max. Op. Min. Rel. Min. Dif. 140 -140 50 60 -60 15 140 -140 20 115 20 20 180 75 25 390 235 30 85 -85 50 180 -180 200 85°C Max. Op. Min. Rel. Min. Dif. 150 -150 50 60 -60 12 140 -140 20 120 15 15 180 70 15 400 215 30 85 -85 50 180 -180 190 125°C Max. Op. Min. Rel. Min. Dif. 200 -200 60 65 -65 12 140 -140 20 123 15 8 190 60 10 410 200 30 100 -100 50 180 -180 160 150°C Max. Op. Min. Rel. Min. Dif. 250 -250 NS 70 -70 10 140 -140 20 125 10 5 200 55 5 420 185 30 110 -110 50 185 -185 140 OPERATE AND RELEASE POINTS SS511AT SS51T SS513AT SS541AT SS543AT SS549AT SS561AT SS566AT For application help: call 1-800-537-6945 Honeywell • Sensing and Control 3 Hall Effect Products Surface Mount Sensors SS5 Series WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office. Or call: 1-800-537-6945 USA 1-800-737-3360 Canada 1-815-235-6847 International MOUNTING DIMENSIONS TAPE DIMENSIONS REEL DIMENSIONS FAX 1-815-235-6545 USA INTERNET www.honeywell.com/sensing info@micro.honeywell.com Sensing and Control Honeywell Inc. 11 West Spring Street Freeport, Illinois 61032 www.honeywell.com/sensing Printed with Soy Ink on 50% Recycled Paper 005841-1-EN IL50 GLO 599 Printed in USA