HF2100-1A-12DEF(257)

HF2 10 0 MINIATURE HIGH POWER RELAY Features File No.:E134517 ● 30A switching capability ● PCB coil terminals, ideal for heavy duty load ● 2.5kV dielectric strength (between coil and contacts) ● Plastic sealed and Dust protected types available File No.:R50153835 ● UL insulation system: Class F available File No.:CQC10002049166 RoHS compliant COIL CONTACT DATA Contact arrangement Contact resistance1) 1A 1B 1C (NO) Approx. 900mW Coil power 50m max.(at 1A 24VDC) Contact material AgSnO2, AgCdO Contact rating (Res. load) 30A 240VAC 15A 240VAC 20A 30VDC 10A 30VDC Max. switching power 11080VA 1200W Max. switching voltage Max. switching current 1C (NC) 4155VA 450W 20A 240VAC 10A240VAC 20A 30VDC 10A 30VDC 5540VA 600W 2770VA 300W 277VAC / 30VDC 40A2) Max.continuous current 15A 20A 10A When PCB terminals carry current≤30A When PCB terminals do not carry current (only QC terminals carry current)≤25A Mechanical endurance 1 x 107OPS Electrical endurance 1A type(Non-plastic sealed): 1 x 105OPS (30A 240VAC, Resistive load, AgCdO, Room temp., 1s on 9s off) Notes:1) The data shown above are initial values. 2) Long time current-carrying under 40A condition is prohibited. CHARACTERISTICS Insulation resistance Dielectric Between coil & contacts strength Between open contacts Operate time (at rated. volt.) Release time (at rated. volt.) Ambient temperature Functional Shock resistance Destructive Vibration resistance Humidity Termination Unit weight Construction 1000M (at 500VDC) 2500VAC 1min 1500VAC 1min 15ms max. 10ms max. -55 C to 85 C 98m/s2 980m/s2 o COIL DATA at 23 Nominal Voltage VDC Pick-up Voltage VDC max.1) Drop-out Voltage VDC min.1) Max. Voltage VDC*2) 5 3.75 0.5 6.5 27 x (1 10%) 6 4.50 0.6 7.8 40 x (1 10%) 9 6.75 0.9 11.7 97 x (1 10%) 12 9.00 1.2 15.6 155 x (1 10%) 15 11.25 1.5 19.5 256 x (1 10%) 18 13.50 1.8 23.4 380 x (1 10%) 24 18.00 2.4 31.2 660 x (1 10%) 48 36.00 4.8 62.4 2560 x (1 10%) 70 52.50 7.0 91.0 5500 x (1 10%) 110 82.50 11.0 143.0 13450 x (1 10%) Coil Resistance Notes:1)The data shown above are initial values. 2)*Maximum voltage refers to the maximum voltage which relay coil could endure in a short period of time. o 10Hz to 55Hz 1.5mm DA 5% to 85% RH PCB & QC Approx. 35g Plastic sealed, Dust protected Notes: 1) For plastic sealed type, the venting-hole should be opened in test. 2) The data shown above are initial values. 3) Please find coil temperature curve in the characteristic curves below. 4) UL insulation system: Class F, Class B. 5) It is recommended that the terminal of the process QC cannot pass through more than 25A current for a long period of time . HONGFA RELAY ISO9001, ISO/TS16949 , ISO14001, OHSAS18001, IECQ QC 080000 CERTIFIED 2019 Rev. 1.00 327 SAFETY APPROVAL RATINGS UL/CUL Contact material Load type General purpose Resistive Ballast Pilot duty AgCdO Motor load Definite 1 Form A 30A 1 Form B 15A 277VAC 30A 30A 125/240VAC 30A 15A 10A 30VDC 20A 277VAC 20A 240VAC 15A 250VAC 40A 125/240/277VAC 6A 3A 125VAC 800VA 290VA 125VAC 690VA 125VAC 800VA 240VAC 1152VA 277VAC 764VA 30A 30A 20A 10A 6A 3A 800VA 290VA 690VA 800VA 768VA 1152VA 768VA 764VA 125VAC 1HP 1/4HP 1HP 1/4HP 240VAC 2HP 1HP 2HP 1HP 125VAC 1HP 125/277VAC 3/4HP 3/4HP 120VAC 82.8LRA, 13.8FLA 82.8LRA, 13.8FLA 1HP 125VAC 96LRA, 30FLA 33LRA, 10FLA 125VAC 60LRA, 20FLA 30LRA, 12FLA (LRA- 125VAC 82.8LRA, 27FLA 60LRA, 20FLA 33LRA, 10FLA 60LRA, 20FLA 30LRA, 12FLA 82.8LRA, 27FLA loaded rotor) 240VAC 80LRA, 30FLA (FLA-full load) 240VAC 41.4LRA, 6.9FLA 41.4LRA, 6.9FLA 277VAC 60LRA, 20FLA 60LRA, 20FLA 125VAC 15A 15A 240VAC 5A General purpose 33LRA, 10FLA 3A 240VAC 3A 125/240VAC 30A Resistive 250VAC 40A General purpose 240VAC 60LRA, 20FLA 33LRA, 10FLA 5A 120VAC 15A Notes: 1) All values unspecified are at room temperature. 2) Only typical loads are listed above. Other load specifications can be available upon request. 328 1 Form C (NO) 1 Form C (NC) 30A 15A 40A purpose Tungsten AgSnO2 Volts 125/240VAC 3A ORDERING INFORMATION HF2100 -1A -12D E T F (XXX) Type Contact arrangement 1A: 1 Form A 1B: 1 Form B 1C: 1 Form C Coil voltage Construction 5, 6, 9, 12, 15, 18, 24, 48, 70, 110VDC 1) Contact material Insulation standard Special E: Plastic sealed Nil: Dust protected T: AgSnO2 Nil: AgCdO F: Class F code3) Nil: Class B XXX: Customer special requirement Nil: Standard Notes: 1) We recommend dust protected types for a clean environment (free from contaminations like H2S, SO2, NO2, dust, etc.). We suggest to choose plastic sealed types and validate it in real application for an unclean environment (with contaminations like H2S, SO2, NO2, dust, etc.). 2) Contact is recommended for suitable condition and specifications if water cleaning or surface process is involved in assembling relays on PCB. 3) The customer special requirement express as special code after evaluating by Hongfa. OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT Unit: mm 1 Form A PCB Layout Wiring Diagram Outline Dimensions (Bottom view) 27.5 3.6 28 2x 2.1 3.8 (Bottom view) (Top view) 2x 1.1 14 17.8 1 Form B 27.5 3.6 2x 2.1 28 3.8 (Bottom view) (Top view) 2x 1.1 14 17.8 329 OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT Unit: mm 1 Form C 27.5 3x 2.1 28 3.6 3.8 2x 1.1 (Bottom view) (Top view) 14 17.8 Remark: 1) In case of no tolerance shown in outline dimension: outline dimension ≤1mm, tolerance should be ±0.2mm; outline dimension ＞1mm and ≤5mm, tolerance should be ±0.3mm; outline dimension ＞5mm, tolerance should be ±0.4mm. 2) The tolerance without indicating for PCB layout is always ±0.1mm. CHARACTERISTIC CURVES MAXIMUM SWITCHING POWER 100 40 30 20 15 ENDURANCE CURVE COIL TEMPERATURE RISE 110 100 DC Coil 1A 1C (NO) 100 30 1A 90 1B 10 1C (NO) 1C (NC) 80 1C (NC) 10 1B 70 30A 60 1 AC Resistive Load 15A 40 DC Resistive 1 Load 10 25A 20A 50 0A 100 200 1000 Contact Voltage (V) 0 10 20 30 40 Contact Current (A) 0 80 90 100 110 120 130 140 150 160 Percentage Of Nominal Coil Voltage Test conditions: Resistive load, AgCdO, Dust protected, Room temp., 1s on 9s off. Disclaimer The specification is for reference only. See to "Terminology and Guidelines" for more information. Specifications subject to change without notice. We could not evaluate all the performance and all the parameters for every possible application. Thus the user should be in a right position to choose the suitable product for their own application. If there is any query, please contact Hongfa for the technical service. However, it is the user’s responsibility to determine which product should be used only. © Xiamen Hongfa Electroacoustic Co., Ltd. All rights of Hongfa are reserved. 330