8473D

Agilent 8473D Planar-Doped Barrier Detector 0.01 to 33.0 GHz Data Sheet This Planar- Doped Barrier (PDB) detector, combines the best characteristics of point- contact and low barrier Schottky to provide performance never before achievable. This new PDB diode technology provides detectors with broadband-flatness, excellent square-law response, and low SWR. These specifications plus the rugged design of the detector make it an excellent value. 8473D Specifications1 Frequency range:2 0.01 to 33.0 GHz Frequency response: ±0.25 dB (0.01 to 14.0 GHz) ±0.4 dB (0.01 to 26.5 GHz) ±1.25 dB (0.01 to 33.0 GHz) (±2.0 dB typical to 40 GHz) SWR: 1.2 (0.01 to 14 GHz) 1.4 (14 to 26.5 GHz) 3.0 (26.5 to 33.0 GHz) (3.0 typical to 40 GHz) Low level sensitivity: > 0.4 mV/µW Maximum operating input: 200 mW Typical short-term maximum input (less than 1 minute): 1 watt Notes: 1. Measured at 25° C and -20 dBm unless otherwise specified. 2. Below 1 GHz RF may leak through the video connector. If objectionable, this may be eliminated with a low pass filter. 3. Tested only to 50,000 ft (15,240 m), capable of much higher performance. Noise (peak to peak with CW power applied to produce 100 mV output, 400 kHz BW): < 50 mV Output polarity (Standard): Negative Option 003: Positive RF connector: APC-3.5 Male (SMA compatible) Output connector: BNC (Female) Environmental capabilities: Operating temperature:3 -65° C to +100° C Temperature cycling: MIL-STD-883. Method 1010.1: (-65° C to +100° C) Agilent Email Updates www.agilent.com/find/emailupdates Get the latest information on the products and applications you select. Remove all doubt Our repair and calibration services will get your equipment back to you, performing like new, when promised. You will get full value out of your Agilent equipment throughout its lifetime. Your equipment will be serviced by Agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts. You will always have the utmost confidence in your measurements. Agilent offers a wide range of additional expert test and measurement services for your equipment, including initial start-up assistance onsite education and training, as well as design, system integration, and project management. For more information on repair and calibration services, go to www.agilent.com/find/removealldoubt www.agilent.com For more information on Agilent Technologies’ products, applications or services, please contact your local Agilent office. The complete list is available at: www.agilent.com/find/contactus Agilent Direct www.agilent.com/find/agilentdirect Quickly choose and use your test equipment solutions with confidence. Americas Canada Latin America United States Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Thailand (877) 894-4414 305 269 7500 (800) 829-4444 1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 1 800 226 008 Europe & Middle East Austria 0820 87 44 11 Belgium 32 (0)2 404 93 40 Denmark 45 70 13 15 15 Finland 358 (0)10 855 2100 France 0825 010 700* *0.125¤ fixed network rates Germany 01805 24 6333** **0.14¤ /minute Ireland 1890 924 204 Israel 972-3-9288-504/544 Italy 39 02 92 60 8484 Netherlands 31 (0)20 547 2111 Spain 34 (91)631 3300 Sweden 0200-88 22 55 Switzerland (French) 41 (21)8113811(Opt 2) Switzerland (German) 0800 80 53 53 (Opt 1) United Kingdom 44 (0)118 9276201 Other European Countries: www.agilent.com/find/contactus Revised: October 24, 2007 Product specifications and descriptions in this document subject to change without notice. © Agilent Technologies, Inc. 2001, 2008 Printed in USA, March 17, 2008 5954-8878