HLMP-CW36-TQBDD

Agilent HLMP-CWxx T-1 ¾ (5mm) Extra Bright Precision Optical Performance White LED Lamps Data Sheet Features • Well defined spatial radiation pattern • High luminous white emission • Viewing angle: 15°, 23° and 30° • Standoff or non-standoff leads • Superior resistance to moisture These T-1 ¾ lamps are untinted, non-diffused, and incorporate precise optics which produce well-defined spatial radiation patterns at specific viewing cone angle. Applications • Electronic signs and signals • Small area illumination • Legend backlighting • General purpose indicators Benefit • Reduced power consumption, higher reliability, and increased optical/mechanical design flexibility compared to incandescent bulbs and other alternative white light sources. HLMP-CW11, HLMP-CW12, HLMP-CW26, HLMP-CW27, HLMP-CW36, HLMP-CW37 Description These high intensity white LED lamps are based on InGaN material technology. A blue LED die is coated by phosphor to produce white. The typical resulting color is described by the coordinates x = 0.31, y = 0.31 using the 1931 CIE Chromaticity Diagram. Caution: Devices are Class 1 ESD sensitive. Please observe appropriate precautions during handling and processing. Refer to Application Note AN-1142 for additional details. Package Dimensions Package Dimension A 5.00 ± 0.20 (0.197 ± 0.008) 8.71 ± 0.20 (0.343 ± 0.008) 1.14 ± 0.20 (0.045 ± 0.008) Package Dimension B 5.00 ± 0.20 (0.197 ± 0.008) 8.71 ± 0.20 (0.343 ± 0.008) DIMENSION H 2.35 (0.093) MAX. 0.70 (0.028) MAX. 31.60 MIN. (1.244) 1.14 ± 0.20 (0.045 ± 0.008) 1.50 ± 0.15 (0.059 ± 0.006) 0.70 (0.028) MAX. CATHODE LEAD 31.60 MIN. (1.244) CATHODE LEAD DIMENSION H: 15°: 12.24 ± 0.25mm (0.482 ± 0.01 inches) 23°: 12.50 ± 0.25mm (0.492 ± 0.01 inches) 30°: 12.00 ± 0.25mm (0.472 ± 0.01 inches) 1.00 MIN. (0.039) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 1.00 MIN. (0.039) 5.80 ± 0.20 (0.228 ± 0.008) CATHODE FLAT 2.54 ± 0.38 (0.100 ± 0.015) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 5.80 ± 0.20 (0.228 ± 0.008) CATHODE FLAT 2.54 ± 0.38 (0.100 ± 0.015) Notes: 1. All dimensions are in millimeters /inches. 2. Epoxy meniscus may extend about 1mm (0.040") down the leads. 3. If heat-sinking application is required, the terminal for heat sink is anode. Part Numbering System H L M P - CW XX - X X X XX Mechanical Option 00: Bulk DD: Ammo Pack Straight Leads Color Bin Options 0: Full color bin distribution B: Color bin 2 & 3 only Maximum Intensity Bin 0: No maximum intensity bin limit Others: Refer to Device Selection Guide Minimum Intensity Bin Refer to Device Selection Guide Viewing Angle and Standoff Option 11: 15˚ without standoff 12: 15˚ with standoff 26: 23˚ without standoff 27: 23˚ with standoff 36: 30˚ without standoff 37: 30˚ with standoff 2 Device Selection Guide Part Number HLMP-CW11-WZ0xx HLMP-CW11-XY0xx HLMP-CW12-WZ0xx HLMP-CW12-XY0xx HLMP-CW12-XYBxx HLMP-CW26-UX0xx HLMP-CW26-VW0xx HLMP-CW27-UX0xx HLMP-CW27-UX2xx HLMP-CW27-VW0xx HLMP-CW36-TW0xx HLMP-CW36-UV0xx HLMP-CW36-UVBxx HLMP-CW37-TW0xx HLMP-CW37-UV0xx HLMP-CW37-UVBxx Typical Viewing Angle, 2θ ½ (Degree) 15 15 15 15 15 23 23 23 23 23 30 30 30 30 30 30 Intensity (mcd) at 20 mA Min. 5500 7200 5500 7200 7200 3200 4200 3200 3200 4200 2500 3200 3200 2500 3200 3200 Max. 16000 12000 16000 12000 12000 9300 7200 9300 9300 7200 7200 5500 5500 7200 5500 5500 Standoff No No Yes Yes Yes No No Yes Yes Yes No No No Yes Yes Yes Package Dimension A A B B B A A B B B A A A B B B Notes: 1. Tolerance for luminous intensity measurement is +/- 15% 2. The luminous intensity is measured on the mechanical axis of the lamp package. 3. The optical axis is closely aligned with the package mechanical axis. 4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper safety equipment. 5. 2θ1/2 is the off-axis angle where the luminous intensity is ½ the on axis intensity Absolute Maximum Rating at TA = 25oC Parameters DC forward current Power dissipation LED junction temperature Operating temperature range Storage temperature range Wave soldering temperature Solder Dipping temperature [2] [2] [1] [3] Value 30 100 105 110 -40 to +85 -40 to +100 250 for 3 seconds 260 for 5 seconds Unit mA mA mW o o o o o Peak pulsed forward current C C C C C Notes: 1. Derate linearly as shown in figure 2. 2. 1.59 mm (0.060 inch) below body 3. Duty factor 10%, frequency 1KHz 3 Electrical/Optical Characteristics TA = 25oC Parameters Forward voltage Reverse Voltage [1] Symbol VF VR RθJ-PIN [2] Min 5.0 Typ 3.2 240 0.31 0.31 70 Max 4.0 Units V V o Test Condition IF = 20 mA IR = 10 µA LED Junction to anode lead IF = 20 mA VF=0, f=1MHz Thermal resistance Chromaticity Coordinates Capacitance C/W X Y C Notes: 1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at IR = 10 µA 2. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device. 1.0 35 IF - FORWARD CURRENT - mA 1.5 RELATIVE LUMINOUS INTENSITY RθJ-A = 585˚C/W RθJ-A = 780˚C/W RELATIVE LUMINOUS INTENSITY 0.8 0.6 0.4 0.2 0.0 380 30 25 20 15 10 5 0 0 1.2 0.9 0.6 0.3 0 0 10 20 FORWARD CURRENT - mA 30 480 580 680 780 WAVELENGTH - nm 100 20 40 60 80 AMBIENT TEMPERATURE - ˚C Figure 1. Relative Intensity vs. Wavelength Figure 2. Forward Current vs. Ambient Temperature Figure 3. Relative Intensity versus DC Forward Current 0.025 IF - FORWARD CURRENT - mA 30 0.020 Y-COORDINATES 1mA 25 20 15 10 5 0 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 VF - FORWARD VOLTAGE - VOLTS Figure 5. Forward Current vs. Forward Voltage 0.015 0.010 5mA 10mA 0.005 0.000 -0.005 -0.010 -0.005 30mA 0.000 0.005 0.010 0.015 20mA X-COORDINATES Figure 4. Chromaticity shift vs. Current *Note: (x,y) values @ 20mA reference to (0,0) RELATIVE LUMINOUS INTENSITY 1 Intensity Bin Limit Table Bin Intensity (mcd) at 20 mA Min Max 1500 1900 2500 3200 4200 5500 7200 9300 12000 16000 21000 0.5 Q R S T 1150 1500 1900 2500 3200 4200 5500 7200 9300 12000 16000 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT (˚) 60 90 U V W X Figure 6. Spatial Radiation Pattern for CW1x 1 Y Z 1 RELATIVE LUMINOUS INTENSITY Tolerance for each bin limit is ± 15% 0.5 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT (˚) 60 90 Figure 7. Spatial Radiation Pattern for CW2x 1 RELATIVE LUMINOUS INTENSITY 0.5 0 -90 -60 -30 0 30 ANGULAR DISPLACEMENT (˚) 60 90 Figure 8. Spatial Radiation Pattern for CW3x Color Bin Limit Table Rank 1 Limits (Chromaticity Coordinates) X Y 0.330 0.360 0.287 0.295 0.264 0.267 0.283 0.305 0.330 0.318 0.296 0.276 0.280 0.248 0.287 0.295 0.356 0.351 0.330 0.318 0.296 0.276 0.330 0.339 0.361 0.385 0.330 0.339 0.283 0.305 0.330 0.360 Y-COORDINATE Color Bin Limits with Respect to CIE 1931 Chromaticity Diagram 0.40 0.35 4 1 BLACK BODY CURVE 2 X Y 0.30 2 3 X Y 3 0.25 4 X Y 0.20 0.26 0.30 0.34 X-COORDINATE 0.38 Tolerance for each bin limit is ± 0.01 Note: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. Please contact your Agilent representative for information on currently available bins. www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2004-2005 Agilent Technologies, Inc. Obsoletes 5989-3101EN July 18, 2005 5989-3532EN