H 2 mm x 5 mm Rectangular LED Lamps Technical Data
HLMP-S100 HLMP-S20X Series HLMP-S30X Series HLMP-S40X Series HLMP-S50X Series HLMP-S600
Features
• Rectangular Light Emitting Surface • Excellent for Flush Mounting on Panels • Choice of Five Bright Colors • Long Life: Solid State Reliability • Excellent Uniformity of Light Output
Package Dimensions
Description
The HLMP-S100, -S200, -S300, -S400, -S500, S600 are epoxy encapsulated lamps in rectangular packages which are easily stacked in arrays or used for discrete front panel indicators. Contrast and light uniformity are enhanced by a special epoxy diffusion and tinting process.
The HLMP-S100 uses double heterojunction (DH) absorbing substrate (AS) aluminum gallium arsenide (AlGaAs) LEDs to produce outstanding light output
5964-9379E
1-153
Electrical/Optical Characteristics at TA = 25°C
Sym. Iv Description Luminous Intensity Device HLMPAlGaAs Red S100 High Efficiency Red S200 S201 Orange S400 S401 Yellow S300 S301 Green S500 S501 Emerald Green S600[4] All Min. Typ. 3.4 2.1 3.4 2.1 3.4 1.4 2.2 2.6 4.2 1.0 7.5 3.5 7.5 3.5 7.5 2.1 4.0 4.0 8.0 3.0 110 Deg. IF = 20 mA See Note 1 Max. Units mcd Test Conditions IF = 20 mA
2θ1/2
Included Angle Between Half Luminous Intensity Points
λPEAK Peak Wavelength
AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green AlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green All
645 635 600 583 565 558 637 626 602 585 569 560 30 90 280 90 500 3100 30 11 4 15 18 35 260
nm
Measurement at Peak
λd
Dominant Wavelength
nm
See Note 2 Time const, e-t/τs
τs
Speed of Response
ns
C
Capacitance
pF
VF = 0; f = 1 MHz
RθJ-PIN Thermal Resistance VF Forward Voltage
°C/W
Junction to Cathode Lead at Seating Plane IF = 20 mA
AlGaAs Red HER/Orange Yellow Green/Emerald Green All
1.6 1.5 1.5 1.5 5.0
1.8 1.9 2.1 2.2
2.2 2.6 2.6 3.0
V
VR
Reverse Breakdown Voltage
V
IR = 100 µA
1-154
Electrical/Optical Characteristics at TA = 25°C (cont’d)
Sym. ηV Description Luminous Efficacy Device HLMPAlGaAs Red High Efficiency Red Orange Yellow Green Emerald Green Min. Typ. 80 145 380 500 595 656 Max. Units Test Conditions
lumens/ watt
See Note 3
Notes: 1. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/ηv, where Iv is the luminous intensity in candelas and ηv is the luminous efficacy in lumens/watt. 4. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.
Absolute Maximum Ratings at TA = 25°C
AlGaAs Red 300 20 30 High Efficiency Red/Orange 90 25 30 500 110 -20 to +100 -55 to +100 260°C for 5 seconds 110 -55 to +100 110 -55 to +100 110 -20 to +100 -55 to +100 Green/ Emerald Green 90 25 30
Parameter Peak Forward Current Average Forward Current[1] DC Current
[2]
Yellow 60 20 20
Units mA mA mA mA °C °C
Transient Forward Current[3] (10 µsec Pulse) LED Junction Temperature Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6 mm (0.063 in.) below seating plane]
Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. For AlGaAs Red, Red, Orange, and Green series derate linearly from 50°C at 0.5 mA/°C. For Yellow series derate linearly from 50°C at 0.34 mA/°C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wire bond. It is not recommended that the device be operated at peak currents beyond the peak forward current listed in the Absolute Maximum Ratings.
1.0 EMERALD GREEN ORANGE AlGaAs RED TA = 25° C
RELATIVE INTENSITY
HIGH PERFORMANCE GREEN
HIGH EFFICIENCY RED
0.5 YELLOW
0 500
550
600 WAVELENGTH – nm
650
700
750
Figure 1. Relative Intensity vs. Wavelength.
1-155
Figure 2. Forward Current vs. Forward Voltage Characteristics. VF (300 mA) for AlGaAs Red = 2.6 Volts Typical.
Figure 3. Relative Luminous Intensity vs. DC Forward Current.
Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. LED Peak Current. ηv (300 mA) for AlGaAs Red = 0.7.
Figure 5. Maximum Tolerable Peak Current vs. Peak Duration. (IPEAK MAX Determined from Temperature Derated IDC MAX).
Figure 6. Relative Luminous Intensity vs. Angular Displacement.
1-156
