H7808AJ

HI-SINCERITY MICROELECTRONICS CORP. Spec. No. : HJ200208 Issued Date : 1998.08.01 Revised Date : 2002.08.09 Page No. : 1/3 H7808AJ H7808BJ 3-TERMINAL POSITIVE VOLTAGE REGULATOR Description TO-252 The H7808_J series of three-terminal positive regulators are available in the TO-252 package. These regulators can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each employs internal current limiting, thermal shut-down and safe operating area protection, making it essen-tially indestructible. If adequate heat sinking is provided, they can deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltages and currents. H7808_J is characterized for operation from 0°C to +125°C, and if operating temperature is always high, please refer to the power dissipation curve. Absolute Maximum Ratings (Ta=25°C) • Input Voltage ....................................................................................................................... 35 V • Total Power Dissipation (TC=25°C) .................................................................. Internally limited • Operating Junction Temperature ....................................................................... 0 °C to +125 °C • Storage Temperature Range .......................................................................... -55 °C to +150 °C • Output Current (TC=25°C) .................................................................................................... 1 A • Lead Temperature (Soldering 10S) ................................................................................. 230 °C Typical Application Schematic Diagram Input Vin 1 H7808_J 2 3 Vout 10K 3.4K 6.3V 200 200 0.3 1K 2K C1 C2 30K Output VREF 26 1.9K 20pF 4K Note: C1 and C2 are required if regulator is located far from power supply filter and load, or oscillation may induced on the loop. 26 4K 1.2 12.1K 1K GND H7808AJ, H7808BJ HSMC Product Specification HI-SINCERITY MICROELECTRONICS CORP. Electrical Characteristics Vin=14V, Io=500mA, 0°C≤Tj≤125°C (unless otherwise noted) Spec. No. : HJ200208 Issued Date : 1998.08.01 Revised Date : 2002.08.09 Page No. : 2/3 Symbol Vo ∆Vo ∆Vo IQ ∆IQ Vn RR VD Isc Ipk ∆Vo / ∆T Symbol Vo ∆Vo ∆Vo IQ ∆IQ Vn RR VD Isc Ipk ∆Vo / ∆T Parameter Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current Average Tc of Vout Parameter Output Voltage Line Regulation Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current Average Tc of Vout Conditions Tj=25°C PD≤15W, 5mA≤Io≤1A Tj=25°C, 10.5V≤Vin≤25V Tj=25°C, 11.5V≤Vin≤17V 5mA≤Io≤1A 250mA≤Io≤750mA Io≤1A, Tj=25°C 5mA≤Io≤1A 10.5V≤Vin≤25V Ta=25°C, 10Hz≤f≤100KHz 11.5V≤Vin≤21.5V, f=120Hz Tj=25°C, Io=1A Tj=25°C Tj=25°C 0°C≤Tj≤+125°C, Io=5mA Conditions Tj=25°C PD≤15W, 5mA≤Io≤1A Tj=25°C, 10.5V≤Vin≤25V Tj=25°C, 11.5V≤Vin≤17V 5mA≤Io≤1A 250mA≤Io≤750mA Io≤1A, Tj=25°C 5mA≤Io≤1A 10.5V≤Vin≤25V Ta=25°C, 10Hz≤f≤100KHz 11.5V≤Vin≤21.5V, f=120Hz Tj=25°C, Io=1A Tj=25°C Tj=25°C 0°C≤Tj≤+125°C, Io=5mA H7808AJ Min Typ Max 7.76 8 8.24 7.76 8 8.24 5 80 5 40 100 50 5.5 8 0.5 1.3 200 68 2 1.5 1.7 -0.8 H7808BJ Min Typ Max 7.7 8 8.3 7.6 8 8.4 5 160 2 80 160 80 5.5 8 0.5 1.3 300 62 73 2.5 1.5 1.7 -0.8 - Units V mV mV mA mA uV dB V A A mV/°C Units V mV mV mA mA uV dB V A A mV/°C H7808AJ, H7808BJ HSMC Product Specification HI-SINCERITY MICROELECTRONICS CORP. TO-252 Dimension A C Spec. No. : HJ200208 Issued Date : 1998.08.01 Revised Date : 2002.08.09 Page No. : 3/3 Marking: H J 7808 Date Code Control Code B D L F G Style: Pin 1.Vin 2.Ground 3.Vout 3 H E K 2 I 1 J 3-Lead TO-252 Plastic Surface Mount Package HSMC Package Code: J *: Typical DIM A B C D E F Inches Min. Max. 0.0177 0.0217 0.0650 0.0768 0.0354 0.0591 0.0177 0.0236 0.2520 0.2677 0.2125 0.2283 Millimeters Min. Max. 0.45 0.55 1.65 1.95 0.90 1.50 0.45 0.60 6.40 6.80 5.40 5.80 DIM G H I J K L Inches Min. Max. 0.0866 0.1102 *0.0906 0.0354 0.0315 0.2047 0.2165 0.0551 0.0630 Millimeters Min. Max. 2.20 2.80 *2.30 0.90 0.80 5.20 5.50 1.40 1.60 Notes: 1.Dimension and tolerance based on our Spec. dated May. 05,1996. 2.Controlling dimension: millimeters. 3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material. 4.If there is any question with packing specification or packing method, please contact your local HSMC sales office. Material: • Lead: 42 Alloy; solder plating • Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 Important Notice: • All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. • HSMC reserves the right to make changes to its products without notice. • HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. • HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: • Head Office (Hi-Sincerity Microelectronics Corp.): 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel: 886-2-25212056 Fax: 886-2-25632712, 25368454 • Factory 1: No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel: 886-3-5983621~5 Fax: 886-3-5982931 H7808AJ, H7808BJ HSMC Product Specification