H7812BM

HI-SINCERITY MICROELECTRONICS CORP. Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 2001.01.30 Page No. : 1/3 H7812AM H7812BM Low Current Positive Voltage Regulator Of Surface Mount Device Description The H7812_M series of surface mount device regulators are easyto-use devices suitable for multitude of applications that require a regulated supply of up to 100mA. These regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the 7812_M devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode resistor combination, as output impedance and quiescent current are substantially reduced. • W ide Range Of Available, Fixed Output Voltages • Internal Short-Circuit Current Limiting • Internal Thermal Overload Protection • No External Components Required Absolute Maximum Ratings (Ta=25°C) • Input Voltage................................................... 30 V (5V Through 9V), 35 V (12V Through 18V) • Total Power Dissipation ........................................................................................... Internal limit • Operating Temperature Range ............................................................................ 0 °C to +70 °C • Maximum Junction Temperature...................................................................................... 125 °C • Storage Temperature Range .......................................................................... -55 °C to +150 °C • Lead Temperature (Soldering 10S).................................................................................. 260 °C Typical Application Schematic Diagram Vin Vin 3 Vout H7812_M 2 100 1 5.7K 5K 100 1.5K 1.9K Vout 5pF 3.41K 13K C1 C2 576 3.89K 7.8K 2.23K A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the input ripple voltage. Note : C1 and C2 are required if regulator is located far from power supply filter and load, or oscillation may induced on the loop H7812AM, H7812BM 2.84K GND HSMC Product Specification HI-SINCERITY MICROELECTRONICS CORP. Electrical Characteristics Vin=19V, Io=40mA, Tj=25°C Cin=0.33uF, Cout=0.1uF (unless otherwise noted) Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 2001.01.30 Page No. : 2/3 Symbol Parameter Conditions Tj=25°C 14.5V≤Vin≤27V 1mA≤Io≤40mA 1mA≤Io≤70mA 14.5V≤Vin≤27V 16V≤Vin≤27V 1mA≤Io≤100mA 1mA≤Io≤40mA Ta=25°C 16V≤Vin≤27V 1mA≤Io≤40mA Ta=25°C 15V≤Vin≤25V, f=120Hz Ta=25°C Ta=25°C Conditions Tj=25°C 14.5V≤Vin≤27V 1mA≤Io≤40mA 1mA≤Io≤70mA 14.5V≤Vin≤27V 16V≤Vin≤27V 1mA≤Io≤100mA 1mA≤Io≤40mA Ta=25°C 16V≤Vin≤27V 1mA≤Io≤40mA Ta=25°C 15V≤Vin≤25V, f=120Hz Ta=25°C Ta=25°C H7812AM Units Min Typ Max 11.64 12 12.36 11.4 11.4 40 12 12 80 54 140 1.7 12.6 12.6 180 110 100 50 5 1 0.1 V Vo Output Voltage ∆Vo ∆Vo IQ Line Regulation Load Regulation mV mV mA mA uV dB mA V Units Quiescent Current Quiescent Current ∆IQ Change Vn Output Noise Voltage ∆Vin / ∆Vout Ripple Rejection Ipk Peak Output Current VD Dropout Voltage Symbol Parameter H7812BM Min Typ Max 11.4 12 12.6 11.4 11.4 40 12 12 80 54 140 1.7 12.6 12.6 180 110 100 50 5 1 0.1 - Vo Output Voltage V ∆Vo ∆Vo IQ Line Regulation Load Regulation mV mV mA mA uV dB mA V Quiescent Current Quiescent Current ∆IQ Change Vn Output Noise Voltage ∆Vin / ∆Vout Ripple Rejection Ipk Peak Output Current VD Dropout Voltage H7812AM, H7812BM HSMC Product Specification HI-SINCERITY MICROELECTRONICS CORP. SOT-89 Dimension Marking : Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 2001.01.30 Page No. : 3/3 C H Date Code Part Number HSMC Logo Package Code B 1 E F G A 2 3 D Style : Pin 1.Vout 2.Ground 3.Vin I 3-Lead SOT-89 Plastic Surface Mounted Package HSMC Package Code : M *:Typical DIM A B C D E Inches Min. Max. 0.1732 0.1811 0.1594 0.1673 0.0591 0.0663 0.0945 0.1024 0.0141 0.0201 Millimeters Min. Max. 4.40 4.60 4.05 4.25 1.50 1.70 2.40 2.60 0.36 0.51 DIM F G H I Inches Min. Max. 0.0583 0.0598 0.1165 0.1197 0.0551 0.0630 0.0138 0.0161 Millimeters Min. Max. 1.48 1.52 2.96 3.04 1.40 1.60 0.35 0.41 Notes : 1.Dimension and tolerance based on our Spec. dated May. 05,1996. 2.Controlling dimension : millimeters. 3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material. 4.If there is any question with packing specification or packing method, please contact your local HSMC sales office. Material : • Lead : 42 Alloy ; solder plating • Mold Compound : Epoxy resin family, flammability solid burning class:UL94V-0 Important Notice: • All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. • HSMC reserves the right to make changes to its products without notice. • HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. • HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory : • Head Office (Hi-Sincerity Microelectronics Corp.) : 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel : 886-2-25212056 Fax : 886-2-25632712, 25368454 • Factory 1 : No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel : 886-3-5983621~5 Fax : 886-3-5982931 • Factory 2 : No. 17-1, Ta-Tung Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel : 886-3-5977061 Fax : 886-3-5979220 H7812AM, H7812BM HSMC Product Specification