LM1117GS-ADJ

1A L.D.O VOLTAGE REGULATOR LM1117GS FEATURES  Output Current up to 1A  Dropout Voltage is 1.2V at Output current  Three Terminal Adjustable(ADJ) or Fixed 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, and 5.0V  Line Regulation typically at 0.1% typ.  Load Regulation typically at 0.2% typ.  Internal Current and Thermal Protection  Surface Mount Package SOT-223-3L  Moisture Sensitivity Level 3 SOT-223-3L APPLICATIONS        Active SCSI Terminators Portable/ Plan Top/ Notebook Computers High Efficiency Linear Regulators SMPS Post Regulators Mother B/D Clock Supplies Disk Drives Battery Chargers ORDERING INFORMATION Device Package LM1117GS-ADJ LM1117GS-x.x SOT-223-3L x.x: Output Voltage = 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, and 5.0V DESCRIPTION The LM1117GS is a low power positive-voltage regulator designed to meet 1A output current. This device is an excellent choice for use in battery-powered applications, as active terminators for the SCSI bus, and portable computers. The LM1117GS features very low quiescent current and very low dropout voltage of 1.2V at a full load and lower as output current decreases. LM1117GS is available as an adjustable or fixed 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, and 5.0V output voltages. The LM1117GS is offered in a 3-pin surface mount package SOT-223-3L. The output capacitor of 10µF or larger is needed for output stability of LM1117GS as required by most of the other regulator circuits. ABSOLUTE MAXIMUM RATINGS CHARACTERISTIC SYMBOL MIN. MAX. UNIT VIN - 20 V Lead Temperature TSOL - 260 °C Storage Temperature Range TSTG −65 150 °C Operating Junction Temperature Range TOPR −40 125 °C Input Supply Voltage May. 2020 – Rev 1.2.1 1/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS ORDERING INFORMATION VOUT Package Order No. Supplied As Status ADJ SOT-223-3L LM1117GS-ADJ Tape & Reel Active 1.2V SOT-223-3L LM1117GS-1.2 Tape & Reel Active 1.5V SOT-223-3L LM1117GS-1.5 Tape & Reel Active 1.8V SOT-223-3L LM1117GS-1.8 Tape & Reel Active 2.5V SOT-223-3L LM1117GS-2.5 Tape & Reel Active 3.3V SOT-223-3L LM1117GS-3.3 Tape & Reel Active 5.0V SOT-223-3L LM1117GS-5.0 Tape & Reel Active May. 2020 – Rev 1.2.1 2/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS PIN CONFIGURATION SOT-223-3L PIN DESCRIPTION Pin No. Pin Name 1 ADJ / GND 2 VOUT 3 VIN Pin Function Adjustable or Ground (Fixed Version) Output Voltage Input Voltage TYPICAL APPLICATION CIRCUITS < Fixed Version> VIN Vin OUT VIN Vin Vout OUT ADJ GND CIN COUT CIN 10µF 10µF 10µF Vout R1 COUT 10µF R2 May. 2020 – Rev 1.2.1 3/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS ELECTRICAL CHARACTERISTICS For ADJ Output Voltage SYMBOL PARAMETER (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 1.250 1.262 V 1.281 V VREF Reference Voltage VIN = 5V, IO = 10mA 1.238 VREF Reference Voltage IO = 10mA to 1A, VIN - VREF = 1.5V to 13.75V (TJ = 0 ~ 125°C) 1.219 ΔVLINE Line Regulation IO = 10mA , VIN - VREF = 1.5V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN - VREF = 2V 0.2 0.4 % 12 V VIN Operating Input Voltage IADJ Adjustment pin Current VIN - VREF = 1.5V to 12V, IO = 100mA 50 120 µA ΔIADJ Adjustment Pin Current Change VIN - VREF = 1.5V to 12V, IO = 100mA to 1A 0.5 5 µA IO(MIN) Minimum Load Current VIN = 5V, VREF = 0V 5 10 mA IO Current Limit VIN - VREF = 5V eN Output Noise (%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VREF = 3V, VRIPPLE = 1VPP SVR 1000 For 1.2V Output Voltage SYMBOL PARAMETER 60 mA 0.003 % 75 dB (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 1.200 1.224 V 1.248 V VO Output Voltage VIN = 2.7V, IO = 10mA 1.176 VO Output Voltage VIN = 2.7V to 12V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 1.152 ΔVLINE Line Regulation IO = 10mA , VIN = 2.7V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 3.2V 0.2 0.4 % 12 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise (%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 1.5V, VRIPPLE = 1VPP SVR May. 2020 – Rev 1.2.1 5 1000 4/12 60 mA 0.003 % 75 dB HTC 1A L.D.O VOLTAGE REGULATOR For 1.5V Output Voltage SYMBOL PARAMETER LM1117GS (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 1.5 1.515 V 1.530 V VO Output Voltage VIN = 3.0V, IO = 10mA 1.485 VO Output Voltage VIN = 3.0V to 12V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 1.470 ΔVLINE Line Regulation IO = 10mA , VIN = 3.0V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 3.5V 0.2 0.4 % 12 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise(%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 3V, VRIPPLE = 1VPP SVR 5 1000 For 1.8V Output Voltage SYMBOL PARAMETER 60 mA 100 µV 75 dB (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 1.8 1.818 V 1.836 V VO Output Voltage VIN = 3.3V, IO = 10mA 1.782 VO Output Voltage VIN = 3.3V to 12V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 1.764 ΔVLINE Line Regulation IO = 10mA , VIN = 3.3V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 3.8V 0.2 0.4 % 12 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise(%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 3V, VRIPPLE = 1VPP SVR May. 2020 – Rev 1.2.1 5 1000 5/12 60 mA 100 µV 75 dB HTC 1A L.D.O VOLTAGE REGULATOR For 2.5V Output Voltage SYMBOL PARAMETER LM1117GS (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 2.5 2.525 V 2.550 V VO Output Voltage VIN = 4.0V, IO = 10mA 2.475 VO Output Voltage VIN = 4.0V to 12V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 2.450 ΔVLINE Line Regulation IO = 10mA , VIN = 4.0V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 4.5V 0.2 0.4 % 12 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise(%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 3V, VRIPPLE = 1VPP SVR 5 1000 For 3.3V Output Voltage SYMBOL PARAMETER 60 mA 100 µV 75 dB (TJ=25°C, COUT = 10µF unless otherwise specified) CONDITIONS MIN. TYP. MAX. UNIT 3.3 3.333 V 3.366 V VO Output Voltage VIN = 4.8V, IO = 10mA 3.267 VO Output Voltage VIN = 4.8V to 12V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 3.234 ΔVLINE Line Regulation IO = 10mA , VIN = 4.8V to 12V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 5.3V 0.2 0.4 % 12 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise(%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 3V, VRIPPLE = 1VPP SVR May. 2020 – Rev 1.2.1 5 1000 6/12 60 mA 100 µV 75 dB HTC 1A L.D.O VOLTAGE REGULATOR For 5.0V Output Voltage SYMBOL LM1117GS (TJ=25°C, COUT = 10µF unless otherwise specified) PARAMETER CONDITIONS MIN. TYP. MAX. UNIT 5.0 5.050 V 5.100 V VO Output Voltage VIN = 6.5V, IO = 10mA 4.950 VO Output Voltage VIN = 6.5V to 15V, IO = 0mA to 1A (TJ = 0 ~ 125°C) 4.900 ΔVLINE Line Regulation IO = 10mA , VIN = 6.5V to 15V 0.1 0.2 % ΔVLOAD Load Regulation IO = 10mA to 1A, VIN = 7.0V 0.2 0.4 % 15 V 10 mA VIN Operating Input Voltage ID Quiescent Current VIN - VO = 5V IO Current Limit VIN - VO = 5V eN Output Noise(%VO) B = 10Hz to 10kHz, TJ = 25°C Supply Voltage Rejection IO = 1A, f = 120Hz, VIN - VO = 3V, VRIPPLE = 1VPP SVR 5 1000 For All Output Voltage SYMBOL VD CONDITIONS µV 75 dB TYP. MAX. UNIT IO = 100mA 1.0 1.1 V IO = 500mA 1.1 1.2 V IO = 1A 1.2 1.3 V Temperature Stability Long Term Stability 1000 hrs, TJ = 125°C Thermal Regulation TA = 25°C 30ms Pulse May. 2020 – Rev 1.2.1 100 (TJ=25°C, COUT = 10µF unless otherwise specified) PARAMETER Dropout Voltage 60 mA 7/12 MIN. 0.5 % 0.3 % 0.003 %/W HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS TYPICAL OPERATING CHARACTERISTICS 1.6 VIN = VOUT + 3.0V IOUT = 10mA 1.5 VIN – VOUT, DROPOUT VOLTAGE (V) OUTPUT VOLTAGE CHANGE(%) 2.0 1.0 ADJ, 1.5V, 1.8V, 2.5V 0.5 0 5.0V -0.5 -1.0 -1.5 1.4 TJ = -40℃ 1.2 TJ = 25℃ 1.0 TJ = 125℃ 0.8 0.6 0.4 0.2 0 -2.0 -50 -25 0 25 50 75 100 125 150 0 100 200 400 500 600 800 1000 IOUT, OUTPUT CURRENT(mA) FREE-AIR TEMPERATURE-℃ DROPOUT VOLTAGE VS OUTPUT CURRENT OUTPUT VOLTAGE CHANGE VS TEMPERATURE 20 IQ, QUIESCENT CURRENT CHANGE (%) 90 80 IADJ, ADJUST PIN CURRENT 300 70 60 IOUT = 10mA 50 40 30 20 15 10 5 0 -5 -10 -15 -20 10 -50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 TA - AMBIENT TEMPERATURE (℃) TA - AMBIENT TEMPERATURE (℃) ADJ PIN CURRENT VS TEMPERATURE QUIESCENT CURRENT CHANGE VS TEMPERATURE May. 2020 – Rev 1.2.1 8/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS APPLICATION CIRCUITS Fig.1 300mA Current Output Fig.2 Typical Adjustable Regulator Fig.3 Negative Supply May. 2020 – Rev 1.2.1 9/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS Fig.4 Voltage Regulator with Reference Fig.5 Battery Backed-up Regulated Supply May. 2020 – Rev 1.2.1 10/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS APPLICATION INFORMATION The LM1117GS can deliver a continuous current of 1A over the full operating junction temperature range. However, the output current is limited by the restriction of power dissipation which differs from packages. A heat sink may be required depending on the maximum power dissipation and maximum ambient temperature of application. With respect to the applied package, the maximum output current of 1A may be still undeliverable due to the restriction of the power dissipation of LM1117GS. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. The temperatures over the device are given by: TC = TA + PD × θCA / TJ = TC + PD × θJC / TJ = TA + PD × θJA where TJ is the junction temperature, TC is the case temperature, TA is the ambient temperature, PD is the total power dissipation of the device, θCA is the thermal resistance of case-to-ambient, θJC is the thermal resistance of junction-to-case, and θJA is the thermal resistance of junction to ambient. The total power dissipation of the device is given by: PD = PIN − POUT = (VIN × IIN) − (VOUT × IOUT) = (VIN × (IOUT + IGND)) − (VOUT × IOUT) = (VIN − VOUT) × IOUT + (VIN × IGND) where IGND is the operating ground current of the device which is specified at the Electrical Characteristics. The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the application, and the maximum allowable junction temperature (TJmax): TRmax = TJmax − TAmax The maximum allowable value for junction-to-ambient thermal resistance, θJA, can be calculated using the formula: θJA = TRmax / PD = (TJmax − TAmax) / PD LM1117GS is available in SOT-223-3L packages. The thermal resistance depends on amount of copper area or heat sink, and on air flow. If the maximum allowable value of θJA calculated above is over 140°C/W for SOT-2233L package, no heat sink is needed since the package can dissipate enough heat to satisfy these requirements. If the value for allowable θJA falls near or below these limits, a heat sink or proper area of copper plane is required. In summary, the absolute maximum ratings of thermal resistances are as follow: Characteristic Symbol θJA-SOT-223 Thermal Resistance Junction-To-Ambient / SOT-223-3L Rating Unit 140 °C/W No heat sink / No air flow / No adjacent heat source / TA=25°C May. 2020 – Rev 1.2.1 11/12 HTC 1A L.D.O VOLTAGE REGULATOR LM1117GS REVISION NOTICE The description in this data sheet is subject to change without any notice to describe its electrical characteristics properly. May. 2020 – Rev 1.2.1 12/12 HTC