LM78L11F

FIXED VOLTAGE REGULATOR 3-TERMINAL 0.1A POSITIVE VOLTAGE REGULATORS This series of fixed-voltage monolithic integrated-circuit voltage regulators is designed for a wide range of applications. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power-pass elements to make high current voltage regulators. Each of these regulators can deliver up to 100㎃ of output current. The internal limiting and thermal shutdown features of these regulators make them essentially immune to overload. When used as a replacement for a zener diode-resistor combination, an effective improvement in output impedance can be obtained together with lower-bias current. ORDERING INFORMATION Device LM78LXX 1. 1. LM78LXX TO-92 (TOP VIEW) SOT-89 1. Output 2. Gnd 3. Input Marking LM78LXX Package TO-92 FEATURES ◇ Output Current Up to 100㎃ ◇ No External Components ◇ Internal Thermal Overload Protection ◇ Internal Short-Circuit Limiting ◇ Output Voltage of 5V, 6V, 8V, 9V, 10V, 12V, 15V, 18V and 24V LM78L05 /A /C LM78L05 /A /C LM78L05NF LM78L05AF/CF LM78L06F~24F XX = Output Voltage or Grade 805 SOT-89 806~824 ABSOLUTE MAXIMUM RATINGS Characteristic LM78L05 /A/C∼ LM78L10 Symbol Value 30 Unit Input voltage LM78L12 ∼ LM78L18 LM78L24 VI 35 40 V Operating junction temperature Storage temperature Soldering temperature and time Topr Tstg Tsol 0 ∼ +150 -65 ∼ +150 260/10sec ℃ Mar. 2006 - Rev 06 HTC 26 FIXED VOLTAGE REGULATOR RECOMMENDED OPERATING CONDITIONS Min. LM78L05 / A / C LM78L06 LM78L08 LM78L09 Input Voltage V I LM78L10 LM78L12 LM78L15 LM78L18 LM78L24 Output current,Io perating virtual junction temperature, 7 8 Max. 20 20 LM78LXX Unit 10.5 11.5 12.5 14.5 17.5 20.5 26.5 23 24 25 27 30 33 39 100 ㎃ ℃ V 0 125 TYPICAL APPLICATION Notes 1. To specify an output voltage, substitute voltage for "XX" 2. Bypass capacitors are recommended for optimum stability and transient response and should be located as close as possible to the regulators. Mar. 2006 - Rev 06 HTC 27 FIXED VOLTAGE REGULATOR LM78L05 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=10V, IO=40㎃ (unless otherwise noted) LM78L05 Characteistic Symbol Test condition * 25℃ Min. 4.8 4.75 4.75 25℃ Typ. 5 5 5 32 26 Max. 5.2 5.25 5.25 150 100 60 30 6 5.5 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 7V≤VI≤20V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 7V≤VI≤20V 8V≤VI≤20V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 15 8 3.8 ㎷ Bias current IB 9V≤VI≤20V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ ㎃ 10Hz≤f≤100kHz 8V≤VI≤18V f=120Hz 25℃ 25℃ 25℃ 41 42 49 1.7 ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 28 FIXED VOLTAGE REGULATOR LM78L05A ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=10V, IO=40㎃ (unless otherwise noted) LM78L05A Characteistic Symbol Test condition * 25℃ Min. 4.9 4.9 4.9 25℃ 25℃ Typ. 5 5 5 5 3 15 8 Max. 5.1 5.1 5.1 50 25 60 30 6 5.5 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 7V≤VI≤20V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 7V≤VI≤20V 8V≤VI≤20V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ ㎷ Bias current IB 9V≤VI≤20V 1㎃≤IO≤40㎃ 25℃ 125℃ 3.8 ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 41 42 49 1.7 ㎃ 10Hz≤f≤100kHz 8V≤VI≤18V f=120Hz ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 29 FIXED VOLTAGE REGULATOR LM78L05C ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=10V, IO=40㎃ (unless otherwise noted) LM78L05C Characteistic Symbol Test condition * 25℃ Min. 4.95 4.95 4.95 25℃ 25℃ Typ. 5 5 5 5 3 15 8 Max. 5.05 5.05 5.05 50 25 50 25 6 5.5 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 7V≤VI≤20V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 7V≤VI≤20V 8V≤VI≤20V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ ㎷ Bias current IB 9V≤VI≤20V 1㎃≤IO≤40㎃ 25℃ 125℃ 3.8 ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ ㎃ 10Hz≤f≤100kHz 8V≤VI≤18V f=120Hz 25℃ 25℃ 25℃ 41 42 49 1.7 ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 30 FIXED VOLTAGE REGULATOR LM78L06 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=10V, IO=40㎃ (unless otherwise noted) LM78L06 Characteistic Symbol Test condition * 25℃ Min. 5.75 5.7 5.7 25℃ Typ. 6 6 6 35 29 Max. 6.25 6.3 6.3 175 125 80 40 6 5.5 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 8V≤VI≤20V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 8V≤VI≤20V 9V≤VI≤20V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 16 9 3.9 ㎷ Bias current IB 9V≤VI≤20V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 40 46 48 ㎃ 10Hz≤f≤100kHz 9V≤VI≤19V f=120Hz ㎶ ㏈ 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 31 FIXED VOLTAGE REGULATOR LM78L08 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=14V, IO=40㎃ (unless otherwise noted) LM78L08 Characteistic Symbol Test condition * 25℃ Min. 7.7 7.6 Typ. 8 8 Max. 8.3 8.4 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 10.5V≤VI≤23V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V 7.6 25℃ 8 42 36 8.4 175 125 80 40 6 5.5 1.5 0.1 ㎃ ㎃ ㎷ ㎷ Line regulation Reg line 10.5V≤VI≤23V 11V≤VI≤23V Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 18 10 Bias current IB 25℃ 125℃ 4 Bias current change △IB 11V≤VI≤23V 1㎃≤IO≤40㎃ 0℃ ∼ 125℃ Output noise voltage Ripple rejection VN RR 10Hz≤f≤100kHz 13V≤VI≤23V f=120Hz 25℃ 25℃ 37 54 46 ㎶ ㏈ Dropout voltage VD 25℃ 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 32 FIXED VOLTAGE REGULATOR LM78L09 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=16V, IO=40㎃ (unless otherwise noted) LM78L09 Characteistic Symbol Test condition * 25℃ Min. 8.6 8.55 Typ. 9 9 Max. 9.4 9.45 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 12V≤VI≤24V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V 8.55 25℃ 9 45 40 9.45 175 125 90 40 6 5.5 1.5 0.1 ㎃ ㎃ ㎷ ㎷ Line regulation Reg line 12V≤VI≤24V 13V≤VI≤24V Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 19 11 Bias current IB 25℃ 125℃ 4.1 Bias current change △IB 13V≤VI≤24V 1㎃≤IO≤40㎃ 0℃ ∼ 125℃ Output noise voltage Ripple rejection VN RR 10Hz≤f≤100kHz 13V≤VI≤23V f=120Hz 25℃ 25℃ 38 58 45 ㎶ ㏈ Dropout voltage VD 25℃ 1.7 V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 33 FIXED VOLTAGE REGULATOR LM78L10 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=17V, IO=40㎃ (unless otherwise noted) LM78L10 Characteistic Symbol Test condition * 25℃ Min. 9.6 9.5 9.5 25℃ Typ. 10 10 10 51 42 Max. 10.4 10.5 10.5 175 125 90 40 6 5.5 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 13V≤VI≤25V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 13V≤VI≤25V 14V≤VI≤25V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 20 11 4.2 ㎷ Bias current IB 14V≤VI≤25V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 37 62 44 1.7 ㎃ 10Hz≤f≤100kHz 15V≤VI≤25V f=120Hz ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 34 FIXED VOLTAGE REGULATOR LM78L12 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=19V, IO=40㎃ (unless otherwise noted) LM78L12 Characteistic Symbol Test condition * 25℃ Min. 11.5 11.4 11.4 25℃ Typ. 12 12 12 55 49 Max. 12.5 12.6 12.6 250 200 100 50 6.5 6 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 14V≤VI≤27V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 14.5V≤VI≤27V 16V≤VI≤27V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 22 13 4.3 ㎷ Bias current IB 16V≤VI≤27V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 37 70 42 1.7 ㎃ 10Hz≤f≤100kHz 15V≤VI≤25V f=120Hz ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 35 FIXED VOLTAGE REGULATOR LM78L15 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=23V, IO=40㎃ (unless otherwise noted) LM78L15 Characteistic Symbol Test condition * 25℃ Min. 14.4 14.25 14.25 25℃ Typ. 15 15 15 65 58 Max. 15.6 15.75 15.75 300 250 150 75 6.5 6 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 17.5V≤VI≤30V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 17.5V≤VI≤30V 19V≤VI≤30V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 25 15 4.2 ㎷ Bias current IB 19V≤VI≤30V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 37 82 44 1.7 ㎃ 10Hz≤f≤100kHz 18.5V≤VI≤28.5V f=120Hz ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 36 FIXED VOLTAGE REGULATOR LM78L18 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=26V, IO=40㎃ (unless otherwise noted) LM78L18 Characteistic Symbol Test condition * 25℃ Min. 17.3 17.1 17.1 25℃ Typ. 18 18 18 70 64 Max. 18.7 18.9 18.9 360 300 180 90 6.5 6 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 20.5V≤VI≤33V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 20.5V≤VI≤33V 22V≤VI≤33V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 27 19 4.7 ㎷ Bias current IB 22V≤VI≤33V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ 25℃ 25℃ 25℃ 32 82 36 1.7 ㎃ 10Hz≤f≤100kHz 21.5V≤VI≤31.5V f=120Hz ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 37 FIXED VOLTAGE REGULATOR LM78L24 ELECTRICAL CHARACTERISTICS (At specified virtual junction temperature, VI=32V, IO=40㎃ (unless otherwise noted) LM78L24 Characteistic Symbol Test condition * 25℃ Min. 23 22.8 22.8 25℃ Typ. 24 24 24 95 78 Max. 25 25.2 25.2 480 400 240 120 6.5 6 1.5 0.1 Unit Output voltage ** VOUT 1㎃≤IO≤40㎃ 26.5V≤VI≤39V 1㎃≤IO≤70㎃ 0℃ ∼ 125℃ V Line regulation Reg line 26.5V≤VI≤39V 29V≤VI≤39V ㎷ Load regulation Reg load 1㎃≤IO≤100㎃ 1㎃≤IO≤40㎃ 25℃ 25℃ 125℃ 41 28 4.8 ㎷ Bias current IB 28V≤VI≤39V 1㎃≤IO≤40㎃ ㎃ Bias current change Output noise voltage Ripple rejection Dropout voltage △IB VN RR VD 0℃ ∼ 125℃ ㎃ 10Hz≤f≤100kHz 27.5V≤VI≤37.5V f=120Hz 25℃ 25℃ 25℃ 30 82 33 1.7 ㎶ ㏈ V Notes *. Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects must be taken into account separately. All characteristics are measured with a 0.33㎌ capacitor across the input and a 0.1㎌ capacitor across the output. **. This specification applies only for DC power dissipation permitted by absolute maximum ratings. Mar. 2006 - Rev 06 HTC 38