1-1393277-5

Automotive Relays PCB Single Relays Power Relay K (Sealed) Ŷ Limiting continuous current 45A Ŷ Wide voltage range Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter, wiper control. Contact Data Typical applications Contact arrangement Rated voltage F076_fcw2b Coil Data Resistive/inductive Headlights loads capacitive loads 1 form C, 1 CO 12VDC 12VDC A/B (NO/NC) 45/30A 40/25A Rated current Limiting continuous current1) 23°C 45/30A 40/25A 85°C 30/25A 25/20A 2) Limiting making current 100/30A 180/60A Limiting breaking current3) 60/30A 60/30A Contact material AgNi0.15 SgSnO2 Min. recommended contact load 1A at 5VDC4) Initial voltage drop, at 10A, typ./max. 20/300mV Operate/release time typ. 5/3ms5) Electrical endurance >2x105 ops. >105 ops. at 13.5VDC, 40A up to 4x60W Mechanical endurance, DC coil >107 ops. 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 35cm2 (double layer 105µm) copper area. Cable cross section 6mm². Boundary conditions: 180°C coil temperature; 130°C solder joint. Solder joint results above 130°C on request. The load circuit shall withstand current applied on 40A MAXI fuse. 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC load voltages. 3) For a load current duration of maximum 3s for a make/break ratio of 1:10. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Max. DC load breaking capacity TE0556-E Load limit curve 1: arc extinguishes, during transit time (changeover contact). Load limit curve 2: safe shutdown, no stationary arc (make contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. Rated coil voltage Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001 12 6.9 12VDC Release voltage VDC 1.2 Coil resistance Ω±10% 90 Rated coil power W 1.6 All figures are given for coil without pre-energization, at ambient temperature +23°C. Other coils on request. Insulation Data Initial dielectric strength between open contacts between contact and coil 500VACrms 500VACrms Other Data EU RoHS/ELV compliance Ambient temperature, DC coil Climatic cycling with condensation, EN ISO 6988 Temperature cycling (shock), IEC 60068-2-14, Na Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 compliant -40 to +85°C6) 3 cycles, storage 8/16h 20 cycles, -40/+85°C (dwell time 1h) 6 cycles, upper air temperature 55°C Coil operating range TE0555-6 Does not take into account the temperature rise due to the contact current E = pre-energization 1 06-2016, Rev. 0616 www.te.com © 2016 TE Connectivity. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Terminal Assignment Bottom view on solder pins Other Data (continued) Damp heat constant, 56 days, upper air temperature 55°C IEC 60068-2-3, method Ca RT III – immersion cleanable version Corrosive gas, IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional), IEC 60068-2-6 (sine pulse form), acceleration, acc. to position 10 to 200Hz, 20 to 40g7) Shock resistance (functional), IEC 60068-2-27 (half sine form single pulses), acceleration, acc. to position 8ms 30g7) Terminal type PCB Weight sealed version approx. 22g (0.77oz) open version approx. 19g (0.67oz) Solderability (aging 3: 4h/155°C) for leaded process (Tm = 183°C), for Pb-free process (Tm = 217°C), IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Storage conditions according IEC 600688 8) Packaging unit sealed version 525 pcs. 1 form C, 1 CO TE1086-A1 6) See coil operating range DC. 7) No change in the switching state >10μs. 8) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Mounting Hole Layout Bottom view on solder pins Dimensions 26.1 ±0.4 8.5 ±0.2 16.0 ±0.3 21.1 ±0.4 10.2 ±0.2 6.0 ±0.2 Assembly and positioning aid 3.4 ±0.1 ø 1.3 +0.1 ø 2.3 +0.1 3.4 ±0.6 3.4 ±0.1 6.6 ±0.3 21.2 ±0.3 12.1 ±0.1 2.2 ±0.1 3.3 ±0.1 ø 2.1 +0.1 3.0 ±0.5*) 2.5 – 3.0 ø 2.3 +0.1 ø 2.3 +0.1 0.55 ±0.25 2.3 ±0.2 Terminals tinned * Additional tin tops max. 1.5mm ) 13.3 ±0.2 TE0580-X2 2 06-2016, Rev. 0616 www.te.com © 2016 TE Connectivity. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Product code structure Typical product code V23076 -A 1 001 -C 13 3 Type V23076 Power Relay K, sealed Terminal A PCB Design 1 Single relay Coil 001 12VDC Contact type C Single contact Contact material 13 AgNi0.15 Contact arrangement 3 1 form C, 1 CO D Single contact 14 AgSnO2 Product code Terminal/Encl. Design Coil Contact Contact mat. Arrangement Part number V23076-A1001-C133 V23076-A1001-D143 PCB, sealed Single relay 12VDC Single AgNi0.15 AgSnO2 1 form C, CO 1393277-4 1393277-6 3 06-2016, Rev. 0616 www.te.com © 2016 TE Connectivity. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change.