Automotive Relays
Plug-in Maxi ISO Relays
Power Relay F7
■ Pin assignment similar to ISO 7588 part 1
■ Customized versions on request
– 24VDC versions with contact gap >0.8mm
– Integrated components (e.g. resistor, diode)
– Customized marking/color
– Special covers (e.g. notches, release features, brackets)
Typical applications
Cross carline up to 70A for example: ABS control, cooling fan, energy
management, engine control, glow plug, heated front screen, ignition,
lamps: front, rear, fog light, main switch/supply relay.
F134J_a_bw
Contact Data
Contact arrangement
1 form A,
1 form A,
1 form A,
1 NO
1 NO
1 NO
Contact gap
–
–
>0.8mm
Rated voltage
12VDC
24VDC
24VDC1)
Limiting continuous current
23°C
70A
70A
70A
85°C
50A
50A
50A
125°C
30A
30A
30A
Limiting making current2)
240A 240A 240A
Limiting breaking current
70A
25A
40A
Limiting short-time current
3)
overload current, ISO 8820-3
1.35 x 50A, 1800s
2.00 x 50A, 5s
3.50 x 50A, 0.5s
6.00 x 50A, 0.2s
Jump start test, ISO 16750-1
24VDC for 5min,
conducting nominal current at 23°C
Contact material
Silver based
Min. recommended contact load4)
1A at 5VDC
Initial voltage drop,
form A (NO) contact at 10A, typ./max.
10/300mV
Frequency of operation at nominal load
6 ops./min (0.1Hz)
Operate/release time typ.
7/2ms5)
Electrical endurance6)
resistive load at 14VDC
>1x105 ops.
–
–
70A
>2x105 ops.
–
–
50A
resistive load at 28VDC
–
>1x105ops. >1x105 ops.
25A
40A
Max. DC load breaking capacity
Contact Data (continued)
Mechanical endurance
>1x106ops.
1) Special high performance 24VDC version with contact gap >0.8mm.
2) The values apply to a resistive or inductive load with suitable spark suppression and
at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current
duration of maximum 3s for a make/break ratio of 1:10.
3) Current and time are compatible with circuit protection by a typical automotive fuse.
Relay will make, carry and break the specified current.
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
5) For unsuppressed relay coil. Any parallel device to the coil will increase the release time.
6) Electrical endurance data is not valid for diode versions. Any diode or pn-junction
parallel to the coil (internal or external) will significantly decrease the electrical lifetime,
especially when used for inductive loads.
Coil Data
Rated coil voltage
12VDC, 24VDC
Coil versions, DC coil
Coil
Rated
Operate
Release
Coil
Rated coil
code voltage voltage voltage
resistance7) power7)
VDC VDC VDC
Ω±10% W
052 12 7.2 1.6 90 1.6
053 24 14.4 3.2 324 1.8
056 24 16.0 4.0 268 2.1
065 24 14.4 2.4 288 2.0
165 24 16.0 4.0 288 2.0
7) Without components in parallel.
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Coil operating range
TEVF4_OVR1
ECR0629-N
Does not tak
the temperat
the contact c
E = pre-ener
Load limit curve: safe shutdown, no stationary arc/make contact.
Load limit curve measured with low inductive resistors verified for 1000 switching events.
03-2020, Rev.0320
www.te.com
© 2020TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Does not take into account the temperature rise due to the contact current
E = pre-energization.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog, product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
1
Automotive Relays
Plug-in Maxi ISO Relays
Power Relay F7 (Continued)
Insulation Data
Other Data (continued)
Initial dielectric strength
between open contacts
between contact and coil
between adjacent contacts
Load dump test
ISO 7637-1 (12VDC), test pulse 5
ISO 7637-2 (24VDC), test pulse 5
Shock resistance (functional)
IEC 60068-2-27 (half sine)
Drop test, free fall
IEC 60068-2-32
Terminal type
Cover retention
pull force
push force
Terminal retention
pull force
push force
resistance to bending
force applied to side
torque
Weight
Resistance to soldering heat THT
IEC 60068-2-20
Packaging unit
plug-in:
plug-in with bracket:
PCB
500Vrms
500Vrms
500Vrms
Vs=+86.5VDC
Vs=+200VDC
Other Data
EU RoHS/ELV compliance
compliant
Protection to heat and fire according UL-94
HB or better8)
Ambient temperature
-40 to 125°C
Climatic cycling with condensation
EN ISO 6988
6 cycles, storage 8/16h
Temperature cycling,
IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min)
Damp heat cyclic,
IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C
Damp heat constant, IEC 60068-2-3, Ca
56 days
Category of environmental protection,
IEC 61810
RTI – dustproof
Degree of protection, IEC 60529
IP54 (dustproof)
Corrosive gas
IEC 60068-2-42 10±2cm3/m3 SO2, 10 days
IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days
Vibration resistance (functional)
IEC 60068-2-6 (sine sweep)
10 to 500Hz, min. 5g8)
6ms, min. 30g.9)
1m onto concrete
plug-in, QC/ PCB
150N
200N
150N
150N
10N10)
10N10)
0.3Nm
approx. 38g (1.3oz)
260°C, 10s
210 pcs.
208 pcs.
315 pcs.
08) Refers to used materials.
09) No change in the switching state >10μs. Valid for NC contacts, NO contact values
significantly higher.
10) Values apply 2mm from the end of the terminal. When the force is removed, the
terminal must not have moved by more than 0.3mm.
Accessories
For details see datasheet Connectors for Maxi ISO Relays
Terminal Assignment
NO
1 form A, NO
NOR
1 form A, NO with resistor
NOD
1 form A, NO with diode
85
87
85
87
85
87
86
30
86
30
86
30
Dimensions
Power Relay F7 with quick connect terminals similar to ISO 8092-1
View of the terminals (bottom view)
25.9 ±0.3
6 ±0.4
15 ±0.1
4 ±0.2
5.3 ±0.1
TE1103-411
25.9 ±0.3
16 ±0.5
24.9 ±0.3
Measurement
reference plane
17 +1/-0.5
4x
0.3
11 ±0.5
ø 1.7 +0.2
6.3 ±0.1
0.8 ±0.05
9.5 ±0.1
2
Quick connect terminal similar to ISO 8092-1
03-2020, Rev. 0320
www.te.com
© 2020 TE Connectivity.
1.2 ±0.05
TE1098-Y1
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Automotive Relays
26.2 MAX.
Plug-in Maxi ISO Relays
26.2 MAX.
Power Relay F7 (Continued)
25.2 MAX.
3.0
Dimensions (continued)
Power Relay F7 with PCB terminals
View of the terminals (bottom view) 1.5
TIN PLATED
Mounting hole TE2104-H1
layout (bottom view)
3.8
3.8
26.2 MAX.
26.2 MAX.
3.8
6x Ø 2.18
30
25.2 MAX.
86
85
2.7
87
3.0
3.8
2x Ø 1.93
8.5
3.8
1.5
TIN PLATED
17.9
8.4
17.0
TE2104-H1
TE2105-Q2
3.8
Product
30 code structure
Typical product code V23134
Type
86
85 V23134
2.7Relay F
Power
Contact 87
arrangement
J
1 form A, 1 NO
Cover
0
Standard
2
Bracket near terminal 86 ISO
Coil
052 12VDC
165 24VDC
Terminal/arrangement
D642 Plug-in/NO
1
Bracket at terminal 30 ISO
053
065
24VDC
24VDC
1 form A, 1 NO
0 052 -D642
056 24VDC
Xnnn Customized (nnn: version number)
Production in Europe (only)
Product code
Arrangement Cover
V23134-J0052-D642
V23134-J0052-X429
V23134-J0052-X439
V23134-J0052-X455
V23134-J0052-X511
V23134-J0052-X4613)
V23134-J0053-D642
V23134-J0065-X4974)
V23134-J0165-X5372)3)
V23134-J1052-D642
V23134-J1052-X281
V23134-J1053-D642
V23134-J2165-X5382)3)
-J
Standard
Coil suppr.
Resistor 680Ω
Diode (cathode 86)
Resistor 470Ω
Resistor 560Ω
Bracket
Resistor 1200Ω
Resistor 560Ω
Resistor 1200Ω
Circuit1)
NO
NOR
NOD
NOR
NO
NOR
NO
NOR
NO
NOR
NO
NOR
Coil
12VDC
Contact mat.
Silver based
Terminals
Plug-in, QC
PCB
Plug-in, QC
24VDC
PCB
Plug-in, QC
12VDC
24VDC
Part number
7-1393303-3
1-1414147-0
1-1414286-0
1-1414610-0
3-1415001-2
1-1414469-0
9-1393303-7
3-1414937-3
3-1904117-4
0-1393304-9
1-1393304-0
1-1393304-1
3-1904117-5
1) See terminal assignment diagrams.
3) Special feature: 14.5mm load terminals.
2) Special feature: contact gap >0.8mm.
4) Packed in tray with 300 pcs. per unit.
Other types on request.
This list represents the most common types and does not show all variants covered by this datasheet.
Production in Asia (only)
Product code
Arrangement
V23134-J0052-D642
V23134-J0052-X429
V23134-J0052-X439
V23134-J0052-X4613)
V23134-J0053-D642
V23134-J0056-X4082)3)
1 form A, 1 NO
Cover
Standard
Coil suppr.
Resistor 680Ω
Diode (cathode 86)
Resistor 560Ω
Resistor 1200Ω
Circuit1)
NO
NOR
NOD
NOR
NO
NOR
Coil
12VDC
Contact mat.
Silver based
24VDC
Terminals
Plug-in, QC
Part number
7-1904094-7
7-1904094-8
7-1904094-9
8-1904094-0
8-1904094-3
8-1904094-4
1) See terminal assignment diagrams.
3) Special feature: 14.5mm load terminals.
2) Special feature: contact gap >0.8mm.
Other types on request.
This list represents the most common types and does not show all variants covered by this datasheet.
03-2020, Rev.0320
www.te.com
© 2020TE Connectivity.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog, product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
3
