1-1617785-9

CII Mid-Range Relays FCB-205 Series, 5 Amperes, DPDT increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other forms of the FCB relay: The Series FCB-205 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably FCB-405 — 5 Amp 4PDT Relay Product Facts n Hermetically Sealed n All Welded Construction n Balanced Force n Permanent Magnet Drive n Contacts rated low level to 5 Amps VDC and 115/200 VAC 400 Hz, 3 Phase n Weight .54 ounces max. (15.4 grams) n Qualified to M83536/1, /2 Contact Rating — Amperes Ratings Are Continuous Duty Type of Load Resistive Inductive Motor Lamp Life (Min.) Cycles x 103 100 20 100 100 28 VDC 5 3 2 1 115VAC 400Hz 5 5 3 1 115/200VAC 400Hz, 3Ø 5 5 3 1 *60 Hz loads rated for 10,000 operations Low Level Switching Capability: With contacts operating a load of 10 to 50 microamperes at 10 to 50 millivolts, the contact resistance miss detection level shall be 100 ohms max. Cycling rate is 1 to 12 per second, for 100,000 operations. Overload Current — 20 AMPS DC, 30 AMPS 400Hz Rupture Current — 25 AMPS DC, 40 AMPS 400Hz Contact Make Bounce —1.0 MILLISECOND AT NOMINAL VOLTAGE Max. Contact Drop at 5 Amps — INITIAL 0.100 VOLTS End of Life — 0.125 VOLTS General Specifications Temperature Rating — -70˚C TO + 125˚C Altitude — 300,000 Feet Shock* — Z, Y, & X Enclosures — 200 g for 6 mS W & M Enclosures (Stud Mtg.) — 100 g for 6 mS T Enclosure (Socket Mounted in Track) — 50 g for 11 mS Vibration, Sinusoidal* — Z, Y, & X Enclosures — 0.12 DA 10 to 70 Hz, 30 g 70-3000Hz W & M Enclosures (Stud Mtg.) — 0.12 DA 10 to 57 Hz, 20 g 57-3000Hz T Enclosure (Socket Mounted in Track) — 0.06 DA 10 to 57 Hz, 10 g 57 to 500Hz, 20 g 500 to 3000 Hz Vibration, Random* — Z, Y, & X Enclosures — 0.4 g2/Hz 50-2000Hz T, W & M Enclosures — 0.2 g2/Hz 50-2000Hz Dielectric Strength — At Sea Level — All circuits to ground and circuit to circuit — 1000 V rms Coil to ground — 1000 V rms At 80,000 Feet — 250 V rms Insulation Resistance — Initial (500 VDC) — 100 MΩ Min. After Life or Environmental Tests — 50 MΩ Min. Operate Time at Nominal Voltage — 4 ms or less Release Time at Nominal Voltage — 4 ms or less * Max. contact opening under vibration or shock 10 microseconds Coil Data Coil Code 1 2 3 4 (A) 5 A. B. C. D. Nominal Voltages Freq. Hz DC Res. (B) 6 12 28 28 48 DC DC DC DC DC 20 Ω 95 Ω 500 Ω 500 Ω 1600 Ω Over Temperature Range Pickup or Dropout or Must Hold Below Volts Above Volts Voltage (C) 4.5 0.3 2.5 9.0 0.75 4.5 18.0 1.5 7.0 18.0 1.5 7.0 36.0 2.5 14.0 CODE 4 COILS HAVE BACK EMF SUPPRESSION TO 42 VOLTS MAX. DC COIL RESISTANCE ± 10% AT 25˚C RELAY WILL STAY IN PICKED-UP STATE DOWN TO MUST HOLD VOLTAGES SHOWN. MAX. OVERVOLTAGE: 6 & 12 VDC COILS 120% OF NOMINAL; ALL OTHERS 110% OF NOMINAL. 5–6 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCB-205 Series, 5 Amperes, DPDT (Continued) Below are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ± .010 and (Millimeters ± .25). Terminals CODE "A" Socket Pin Terminals Socket Pins Gold Plated. Polarizing pin tin/lead plated .050 ± .005 .170 (1.27 ± (.13) (4.32) Silicone Rubber Gasket .200 (5.08) CODE Solder Pin Terminals "B" All Terminals Tin/Lead Plated CODE Solder Hook Terminals Hook Terminals Tin/Lead Plated "C" .170 (4.32) .200 (5.08) .050 ± .002 (1.27 ± .05) polarizing pin .050 ± .002 (1.27 ± .05) polarizing pin -X2 .065 DIA (1.65) .040 ± .002 Dia Pin (1.02 ± .02) 8 Places .210 (5.33) -X2 -X2 +X1 CODE "H" +X1 .040 ± .001 Dia Pin (1.02 ± .02) 8 Places BLUE BEAD 90˚ Solder Pins .040 ± .002 Dia Pin (1.02 ± .02) 8 Places BLUE BEAD CODE "Z" All Pins Bright Acid Tin/lead .150± .015 (3.81) CODE "Y" .640 Max. (16.26) .640 Max (16.26) .150 (3.81) .025 (.64) .810 Max. (20.57) 1.078 (27.38) 1.062 (26.92) 5 .133 (3.38) .410 Max. (10.4) .312 (7.92) CII Mid-Range Relays Dimensions: Inches ± .010 (mm ± .25) Enclosure "T" is for use with track mounted sockets and requires socket pin terminals, but no gasket. The gasket is included in the socket assembly. .141 (3.58) .640 Max (16.26) FULL R 4 PLCS .156 (3.96) 1.280 Max. (32.57) All Enclosures have Cupro-Nickel Cans bright acid tin/lead plated after assembly to terminal headers. .312 (7.92) .410 Max. (10.41) .150± .015 .210 (3.81) (5.33) Enclosures CODE "X" FULL R 4 PLCS .810 Max. (20.57) .040± .020 R Typ. .150 BLUE BEAD (3.81) .040 ± .001 Dia Pin (1.02 ± .02) 8 Places +X1 BLUE BEAD .133 (3.38) CODE "W" CODE "T" .410 Max. (10.41) .080 ±.005 (2.03 ± .13) .500 (12.7) .172 (4.37) 4-40 UNC-2A 2 Studs * .693 Max. (17.6) .320 (8.13) .810 Max. (20.57) 1.062 (26,92) 1.078 (27.38) M83536/2-028 (REFERENCE ONLY) .810 Max. (20.57) .158 ±.005 ** (4.01 ± .13) .640 Max. (16.26) .375 (9.52) .032 (.79) .810 Max. (20.57) .055 ±.005 (1.38 ± .13) .410 Max. (10.41) .055 ±.005 (1.38 ± .13) .110 ±.005 (2.79 ± .13) *Metric threads available,To specify use M in place of W NOTE: FOR USE WITH TRACK MOUNT PER MIL-R-6106/23 .410 Max. (10.4) ** MEASURED FROM SURFACE OF HEADER 1.280 Max. (32.51) .025 (.64) 5–7 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCB-205 Series, 5 Amperes, DPDT (Continued) Terminal Wiring Transient Suppression DC Coils POLARIZING PIN 3 - X2 POLARIZING PIN 2 1 - X2 3 2 1 B B + X1 + + A X1 BLUE BEAD A + BLUE BEAD NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. .150 Typ (3.81) 3 Polarizing Pin -X2 2 1 B Diodes used in transient suppression and in AC rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header. .075 (1.90) A .075 (1.90) +X1 Blue Bead .150 Typ (3.81) TERMINAL VIEW HOW TO ORDER FCB-205-A Y 4 RELAY TYPE TERMINALS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 5–8 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com