1-1617787-1

CII Mid-Range Relays FCB-405 Series, 5 Amperes, 4PDT The Series FCB-405 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FCB-205 — 5 Amp DPDT Relay Product Facts n Hermetically Sealed n All Welded Construction n Balanced Force n Permanent Magnet Drive n Contacts rated low level to 5 Amps 28 VDC and 115/200 VAC 400 Hz, 3 Phase n Weight .93 ounces max. (26.4 grams) n Qualified to M83536/5 & /6 Contact Rating — Amperes Ratings Are Continuous Duty Type of Load Resistive Inductive Motor Lamp Life (Min.) Cycles x 103 100 20 100 100 28 VDC 5 3 2 1 115VAC 400Hz 5 5 3 1 115/200VAC 400Hz-3Ø 5 5 3 1 Low Level Switching Capability: With contacts operating a load of 10 to 50 microamperes at 10 to 50 millivolts, the contact resistance miss detection level shall be 100 ohms max. Cycling rate is 1 to 12 per second, for 100,000 operations. Temperature Rating — -70˚C TO + 125˚C Altitude — 300,000 Feet Shock* — Z & Y Enclosures — 200 g for 6 mS W, X & M Enclosures — 100 g for 6 mS T Enclosure (In Track) — 50 g for 11 mS Vibration, Sinusoidal* — Z & Y Enclosures — 30 g 70-3000Hz W, X & M Enclosures — 20 g 70-3000Hz T Enclosure (Socket Mounted in Track) — 20 g 500-3000 Hz Vibration, Random* — Z & Y Enclosures — 0.4 g2/Hz 50-2000Hz T, W, X & M Enclosures — 0.2 g2/Hz 50-2000Hz Dielectric Strength — At Sea Level — All circuits to ground and circuit to circuit — 1000 V rms Coil to ground — 1000 V rms At 80,000 Feet — 250 V rms Insulation Resistance — Initial (500 VDC) — 100 MΩ Min. After Life or Environmental Tests — 50 MΩ Min. Operate Time at Nominal Voltage — 6 ms or less Release Time at Nominal Voltage — 6 ms or less 5 CII Mid-Range Relays Overload Current — 20 AMPS DC, 30 AMPS 400Hz Rupture Current — 25 AMPS DC, 40 AMPS 400Hz Contact Make Bounce —1.0 MILLISECOND AT NOMINAL VOLTAGE Max. Contact Drop at 5 Amps — INITIAL 0.100 VOLTS End of Life — 0.125 VOLTS General Specifications * Max. contact opening under vibration or shock 10 microseconds Coil Data Coil Code 1 2 3 4 (A) 5 A. B. C. D. Nominal Voltages Freq. Hz DC Res. (B) 6 12 28 28 48 DC DC DC DC DC 25 Ω 78 Ω 400 Ω 400 Ω 1275 Ω Over Temperature Range Pickup or Dropout or Must Hold Below Volts Above Volts Voltage (C) 4.5 0.3 2.5 9.0 0.75 4.5 18.0 1.5 7.0 18.0 1.5 7.0 36.0 2.5 14.0 CODE 4 COILS HAVE BACK EMF SUPPRESSION TO 42 VOLTS MAX. DC COIL RESISTANCE ± 10% AT 25˚C RELAY WILL STAY IN PICKED-UP STATE DOWN TO MUST HOLD VOLTAGES SHOWN. MAX. OVERVOLTAGE: 6 & 12 VDC COILS 120% OF NOMINAL; ALL OTHERS 110% OF NOMINAL. 5–9 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCB-405 Series, 5 Amperes, 4PDT (Continued) Below are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ± .010 and (Millimeters ± .25). Terminals CODE "A" Socket Pins - All DC Coils CODE "B" Solder Pin Terminals PIN TERMINALS ARE GOLD PLATED .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .170 (4.32) PIN TERMINALS TIN/LEAD PLATED .170 (4.32) .040 ± .001Dia. Pin (1.02 ± .02) 14 Plcs -X2 CODE "C" Solder Hook Terminals HOOK TERMINALS TIN/LEAD PLATED .210 (7.62) .040 ±.002Dia. Pin (1.02 ±.05 ) 14 Plcs -X2 .210 (7.62) -X2 +X1 +X1 BLUE BEAD BLUE BEAD CODE "T" BLUE BEAD All Enclosures have cupro-Nickel cans bright acid tin/lead plated after assembly to terminal headers. .080 ± .005 (2.03) (± .13) .640 Max. (16.26) +X1 Enclosures M83536/6-025 (REFERENCE ONLY) CODE "Z" .640 Max. (16.26) Dimensions: Inches ± .010 (mm ± .25) .810 Max. (20.37) .055 ± .005 (1.38) (± .13) .065 Dia. typ (1.65) .040 ±.002 Dia. Pin (1.02 ±.05 )14 Plcs .158 ** ± .005 (4.01) (± .13) .110 ± .005 (2.79) (± .13) Code "T" used only with trackmounted Sockets. Requires code "A" pin terminals. Gasket is included in the socket assembly. .810 Max. (20.37) .810 Max. (20.37) .810 Max. (20.37) .430 (10.92) CODE "Y" ± .005 (± .13) CODE "W" ** Measured from surface of header CODE "X" .141 Typ (3.58) 1.078 (27.38) 1.062 (26.92) .640 Max. (16.26) .133 Typ (3.38) .810 Max. (20.37) .405 (10.29) .600 (5.24) 1.280 (32.51) .810 Max. (20.37) 1.078 (27.38) 1.062 (26.92) .141 (3.58) .810 Max. (20.37) FULL R 8 PLCS .810 Max. (20.57) .025 (.64) .640 Max. (16.26) .025 (.64) .500 (12.70) .250 (6.35) .156 (3.96) .172 Dia (4.37) .133 Typ (3.38) 4-40 UNC-2A 3 Studs * .500 (12.7) .712 (18.0) .250 (6.35) .500 (12.70) .375 (9.52) ± .031 ± (.79) .032 (.79) .640 Max. (16.26) 1.280 (32.51) FULL R 6 PLCS .810 Max. (20.37) .810 Max. (20.37) 5–10 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCB-405 Series, 5 Amperes, 4PDT (Continued) Terminal Wiring DC Coils with Transient Suppression DC Coils - 3 X2 2 1 D 2 - 3 X2 C C + X1 + B + 1 D + X1 A B A BLUE BEAD BLUE BEAD NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in AC rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header. .450 (3.81) .150 (3.81) .150 (3.81) -X2 .300 (7.62) .450 (11.43) +X1 BLUE BEAD 5 CII Mid-Range Relays TERMINAL VIEW HOW TO ORDER FCB-405-A Y 4 RELAY TYPE TERMINALS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 5–11 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com