1-647401-4

CONNECTORS/APPLIANCES MTA, CST-100 II AND SL-156 CONNECTORS APPLIANCES /// MTA, CST-100 II AND SL-156 CONNECTORS Contents Introduction This catalog has been designed to assist you, our customer, identify products to satisfy your connector needs for printed circuit board headers, mass termination connectors preloaded with contacts, crimp-snap contacts and housings, and card edge connectors with preloaded contacts. The list at right identifies by centerline the types of product available and is meant to be of assistance to you in the product selection process. IDC MTA-100 Introduction and Table of Contents.......................................................................................2, 3 Connector Selection Guide...............................................................................................................3 .100 [2.54] Centerline Connectors MTA-100 IDC Connectors and Headers................................................................................... 4-23 Introduction...........................................................................................................................................4 Wire-to-Board Mateability Guide.............................................................................................5, 6 Connectors—UL94V-2 and UL94V-0 Closed End with and without Polarizing Tab..................................................................7, 8 Feed-Thru with and without Polarizing Tab.....................................................................7, 8 LED Closed End and Feed-Thru—UL94V-2......................................................................7, 8 Accessories.................................................................................................................................... 9, 10 Posted Connectors Mateability Guide...............................................................................11, 12 MTA-100 Posted Connectors (Wire-to-Wire) UL94V-2 Closed End...................................................................................................................................... 13 Feed-Thru........................................................................................................................................ 13 Headers—UL94V-0 Flat—Straight and Right-Angle Posts................................................................................... 14 Narrow Flat—Straight and Right-Angle Posts................................................................... 15 Polarized—Straight and Right-Angle Posts....................................................................... 16 Friction Lock—Straight and Right-Angle Posts................................................................ 17 Headers with Retention Peg—Straight Posts.................................................................... 18 High Profile Headers—Right-Angle Posts........................................................................... 19 Polarized—High Temperature, Straight and Right-Angle Posts................................. 20 Friction Lock—High Temperature, Straight and Right-Angle Posts......................... 21 Polarized—Surface Mount, Straight...................................................................................... 22 Friction Lock—Surface Mount, Straight ............................................................................. 22 Shrouded—Straight and Right-Angle Posts....................................................................... 23 CST-100 II Crimp Contacts, Housings and Shrouded.....................................................24, 25 Crimp CST-100 II IDC MTA-156 PAGE 2 .156 [3.96] Centerline Connectors MTA-156 IDC Connectors and Headers.................................................................................26-46 Introduction........................................................................................................................................ 26 Wire-to-Board Mateability Guide........................................................................................27, 28 Connectors—UL94V-2 and UL94V-0 Closed End with Locking Ramp, with and without Polarizing Tabs......................... 29 Closed End without Locking Ramp, with and without Polarizing Tabs.................. 30 Feed-Thru with Locking Ramp, with and without Polarizing Tabs........................... 31 Feed-Thru without Locking Ramp, with and without Polarizing Tabs.................... 32 Accessories...................................................................................................................................33-35 Posted Connectors Mateability Guide...............................................................................36, 37 MTA-156 Posted Connectors (Wire-to-Wire)—UL94V-2 Closed End...................................................................................................................................... 38 Feed-Thru........................................................................................................................................ 38 MTA-156 Headers—UL94V-0 Flat—Straight Posts..................................................................................................................... 39 Flat—Right-Angle Posts............................................................................................................. 40 Friction Lock—Straight Posts.................................................................................................. 41 Friction Lock—Right-Angle Posts.......................................................................................... 42 Polarized Lock—Straight Posts............................................................................................... 43 Polarized Lock—Right-Angle Posts....................................................................................... 44 Friction Lock—High Temperature, Straight Posts............................................................ 45 Shrouded—Straight and Right-Angle Posts....................................................................... 46 Contents (continued) SL-156 Crimp Connectors and Headers................................................................................47-51 Wire-to-Board Mateability Guide............................................................................................... 47 Wire-to-Board Crimp Contacts and Keying Plugs............................................................... 48 Wire-to-Board Housings—UL94V-0........................................................................................... 49 Housings with Through Board Latch—UL94V-2................................................................... 50 Housings and Contacts for Large Insulation Diameter (LID) Wire................................ 51 Crimp SL-156 MTA Wire Selection and Ribbon Cable Preparation.................................................................. 52 IDC Ribbon Cable................................................................................................................................53-56 Need More Information? Call Technical Support at the numbers listed on the back of this catalog. Technical Support is staffed with specialists well versed in TE products. They can provide you with: • • • • • MTA Wire Termination Flowchart....................................................................................................... 57 MTA Application Tooling.................................................................................................................58-61 Part Number Index..............................................................................................................................62-64 Global Contacts......................................................................................................................................... 65 TE Technical Support............................................................................................................................... 66 Technical support Catalogs Technical Documents Product Samples Authorized Distributor Locations Contact Termination Wire-to-Wire Options No. of Positions Wire Size (AWG) Wire Insulation Dia. Max. Current Rating (A)** Voltage Rating Max. (VAC) Operating Temp. Range (°C) UL Flammability Replacement Contacts MTA-100 IDC Connectors and Headers .100 2.54 IDC Planned 2-28 28-22 .060* 1.52 5 250 -55 to +105 V-0 & V-2 Yes CST-100 II Contacts and Housings .100 2.54 Crimp Planned 2-28 26-22 .065 1.65 4 250 -55 to +105 V-0 Yes .156 3.96 IDC Yes 2-24 16-18 .095* 2.41 7 600 -55 to +105 V-0 & V-2 Yes 24-18 .105 2.67 10 250 -25 to +105 V-0 Yes 24-16 .112 2.84 10 250 -25 to +105 V-0 Yes Product Name .100" Centerline .156" Centerline MTA-156 Connectors and Headers SL-156 Contacts and Housings .156 3.96 Crimp No 1-24; 2-10 w/ through board latch SL-156 Large Ins. Dia. (LID) Contacts and Housings .156 3.96 Crimp No 2-24 *When terminated one position at a time. **Current Rating is application dependent. PAGE 3 Approvals Centerline CONNECTOR SELECTION GUIDE MTA, CST-100 II and SL-156 Connectors .100 [2.54] Centerline MTA-100 IDC Connectors and Headers PRODUCT FACTS • Connectors and headers for 2 through 28 positions; wire sizes of 22, 24, 26 and 28 AWG [0.4-0.08 mm2] • Wire-to-Post Connectors preloaded with dual beam contacts • Connectors and headers, except shrouded headers, are end-to-end stackable • Connector styles include both closed end and feed thru connectors with locking ramps, with and without polarizing tabs • Molded ribs on housing do not allow reverse mating • Posted connectors for 2 through 19 positions • Connectors preloaded with IDC contacts • All contacts are slotted for insulation displacement (IDC) terminal technique • Contacts are lubricated for fretting corrosion protection • Benefits derived from the MTA-100 system include increased quality and ease of handling such as: • • • • • • One-step assembly No wire stripping No contact damage Reduced wiring errors Simpler tooling Simple maintenance and repair • Meets the material requirements of Table 23.1 of UL1410 Standards for Television Receiver and Video Products (wire-to post connectors only) • Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 • Certified by Canadian Standards Association, File No. LR7189 Technical Documents Product Specification 108-1050 MTA-100 Connectors Application Specifications 114-1019 MTA-100 Connectors 114-1031 MTA-100 Ribbon Cable Assembly MTA-100 connectors accept discrete and ribbon cable wire sizes ranging from 22–28 AWG [0.4–0.08 mm2] with maximum insulation outside diameter of .060 [1.52] for terminating single wire and .050 [1.27] for mass termination of wires. Tin PAGE 4 plated solid, fused stranded, or stranded (7 strands) wire with PVC insulation can be used on 22–28 AWG [0.4–0.9 mm2] MTA-100 connectors and 19 stranded wire on 22–24 AWG [0.4–0.2 mm2] MTA-100 connectors. Only one wire to be terminated into an IDC contact slot. The wire-to-post connector housing material is flame retardant thermoplastic, either UL94V-2 or UL94V-0 rated. A full line of .100 [2.54] centerline headers completes the system. Headers are available with straight or right-angle posts, in flat, polarized or friction lock styles. Headers are available in 2 through 28 positions. Shrouded headers are available in 2 through 14 positions. Performance Data* Voltage Rating—250 vac Current Rating—5 amp max. Low-Level Resistance— 6 mΩ max. initial Dielectric Withstanding Voltage— 750 vac/1 min. Insulation Resistance— 5000 MΩ min. initial Operating Temperature— -55° C to +105° C Note: Refer to page 52 for approved wire listings. *Refer to the Product Specification for additional electrical, mechanical and environmental performance tests and requirements. MTA, CST-100 II and SL-156 Connectors MTA-100 Connector/Header Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. 640 452 640 453 640 454 640 455 640 456 640 457 644 456 644 457 644 486 644 488 644 694 644 695 644 803 644 861 644 874 644 875 644 876 644 877 644 892 644 893 644 894 647 047 647 048 647 050 647 05 647 1 106 647 166 647 502 647 531 647 6 09 647 623 647 532 1744 075 Headers Connectors Matrix for Tin Plated Part Numbers 640440 640441 640442 640443 640468 640469 640470 640471 640620 640621 640622 640623 641311 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 641313 641314 641534 641535 641536 641537 641653 641654 641655 641656 643498 643813 643814 643815 643816 643828 644083 644312 644313 644497 644511 644512 644513 644514 644540 644563 644564 644565 644574 644575 644576 644577 644578 644579 644795 *1375820 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y *Select contact plating to match header plating. PAGE 5 MTA, CST-100 II and SL-156 Connectors MTA-100 Connector/Header Mateability Guide (continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.00076] Gold Plated Part Numbers Connectors 6412 11 6412 12 6412 13 6412 14 6412 15 6412 16 644 487 644 489 644 884 644 885 644 886 644 887 644 896 644 897 644 898 647 108 647 109 647 114 647 116 647 117 647 168 647 62 647 6 624 647 534 1744 047 1744 163 Headers 641237 641238 641239 641240 641241 641242 641243 641244 644020 644042 644043 644044 644702 644726 *1375820 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N N N N N N N N N N Y N N N N N N N N N N N N N N Y N N N N N N N N N N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y *Select contact plating to match header plating. Matrix for .000015 [0.00038] Gold Plated Part Numbers Connectors 6411 22 6411 23 6411 24 6411 25 6411 26 6411 27 644 888 644 889 644 890 644 891 647 075 647 076 647 078 647 079 647 107 647 167 647 467 647 625 647 627 647 533 1744 074 Headers 641190 Y 641191 Y 641192 Y 641193 Y 641198 Y 641199 Y 641200 Y 641201 Y 644038 Y 644040 Y 647477 Y 647480 Y *1375820 N 1744020 Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y *Select contact plating to match header plating. PAGE 6 Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y MTA, CST-100 II and SL-156 Connectors MTA-100 IDC Connectors—Closed End and Feed-Thru Material and Finish Closed End Connectors Housing—UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts—Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold-plated over nickel .275 [6.99] A .056 [1.42] .075 [1.91] .245 .275 [6.99] [6.22] .184 [4.67] Color Coding by Wire Size for UL94V-2 Connectors .100 Typ. [2.54] .520 [13.21] 28 AWG—Green 26 AWG—Blue 24 AWG—White 22 AWG—Red Without Polarizing Tabs .075 [1.91] All wire sizes in UL94V-0—Black .228 [5.80] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 13 thru 23. With Polarizing Tabs Notes: 1. Refer to pages 52-56 for approved wire listing. 2. For strain reliefs and dust covers, see page 9. Feed-Thru Connectors 3. For keying plugs, see page 10. 4. Other circuit sizes are available upon request. Minimums may apply. .275 [6.99] 5. Connector circuits can be molded closed for keying purposes. Minimums may apply. 6. Where no part numbers appear in the chart, parts can be made available upon request. Minimums may apply. 7. To determine connector overall length (dim. A), multiply .100 x the number of circuits. Example: .100 x 10 circuits equals 1.000 inch [25.4 mm]. A .075 [1.91] .305 [7.75] .056 [1.42] .245 [6.22] .184 [4.67] .100 Typ. [2.54] .520 [13.21] Without Polarizing Tabs .075 [1.91] .228 [5.80] With Polarizing Tabs PAGE 7 MTA, CST-100 II and SL-156 Connectors MTA-100 IDC Connectors—Closed End and Feed-Thru MTA-100 IDC Connectors—Closed End and Feed-Thru (continued) Connector Ordering Information The “Base Part Numbers” Chart at right shows the base part number, and their RoHS (Restrictions on Certain Hazardous Substances) Compliant (lead free) equivalent available for the described connectors. Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position closed end connector without polarizing tabs for 22 AWG wire would be: Base number 640440 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640440-0 All part numbers are the RoHS equivalent version. Example: No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-640440-2 3 3-640440-3 4 3-640440-4 5 3-640440-5 6 3-640440-6 7 3-640440-7 8 3-640440-8 9 3-640440-9 10 4-640440-0 11 4-640440-1 12 4-640440-2 13 4-640440-3 14 4-640440-4 15 4-640440-5 16 4-640440-6 17 4-640440-7 18 4-640440-8 19 4-640440-9 20 5-640440-0 21 5-640440-1 22 5-640440-2 23 5-640440-3 24 5-640440-4 25 5-640440-5 26 5-640440-6 27 5-640440-7 28 5-640440-8 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 8 Base Part Numbers Closed End Without Tabs With Tabs Feed-Thru Without Tabs With Tabs Connector Type Connector RoHS Connector RoHS Connector & Wire Size Part Nos. Equiv. Part Nos. Equiv. Part Nos. Standard UL94V-2, Tin Plated 22 AWG 640440 0.3–0.4 mm 2 24 AWG 640441 0.2 mm 2 26 AWG 640442 0.12–0.15 mm 2 28 AWG 640443 0.08–0.09 mm2 RoHS Connector RoHS Equiv. Part Nos. Equiv. 32–58 643813 32–58 640620 32–58 644540 1 32–45 32–58 643814 32–58 640621 32–58 644563 1 32–54 32–58 643815 32–58 640622 32–58 644564 1 32–45 32–58 643816 32–58 640623 32–58 644565 1 32–45 42–68 641311 32–58 — — 32–58 641312 32–58 — — 32–58 641313 32–58 — — 32–58 641314 32–58 — — 32–58 641241 32–58 Tape Mounted on Reel UL94V-2, Tin Plated 22 AWG 640468 32–58 644511 0.3–0.4 mm2 24 AWG 640469 32–58 644512 0.2 mm 2 26 AWG 640470 32–58 644513 0.12–0.15 mm 2 28 AWG 640471 32–58 644514 0.08–0.09 mm2 Standard UL94V-2, .000030 [0.00076] Gold Plated 22 AWG 641237 32–58 644042 0.3–0.4 mm2 24 AWG 641238 32–58 644020 0.2 mm2 26 AWG 1 641239 32–58 644043 0.12–0.15 mm 2 28 AWG 641240 32–58 644044 1 0.8–0.9 mm2 — 644795 32–45 32–58 641242 32–58 32–44 641243 32–58 32–44 641244 32–58 — 641198 32–58 647477 641199 32–58 — 641200 32–58 641201 32–58 — — 641653 32–33 — — 641654 32–33 — — Standard UL94V-2, .000015 [0.00038] Gold Plated 22 AWG 641190 32–58 644038 1 32–44 0.3–0.4 mm2 24 AWG 641191 32–58 1744020 1 32–44 0.2 mm2 26 AWG 641192 32–58 644040 1 32–44 0.12–0.15 mm2 28 AWG 641193 32–58 — — 0.08–0.09 mm 2 LED*, UL94V-2, Tin Plated (See Note 1) 22 AWG 641534 32–33 0.3–0.4 mm2 24 AWG 641535 32–33 0.2 mm2 26 AWG 641536 32–33 0.12–0.15 mm 2 28 AWG 641537 32–33 0.08–0.09 mm2 644702 1 — 32–33 — 644726 1 647480 — 32–45 — 32–46 — 32–43 — — 641655 32–33 — — — — 641656 32–33 — — Standard UL94V-0, Tin Plated (Gold is available, minimums may apply.) (Black in color) 22 AWG 32–45 644578 1 643498 1 32–45 644083 1 32–45 644575 1 0.3–0.4 mm2 24 AWG 644574 1 32–45 644312 1 32–45 644576 1 32–45 644579 1 0.2 mm 2 26 AWG 643828 1 32–45 644313 1 32–45 644577 1 32–45 644497 1 0.12–0.15 mm 2 32–45 32–45 32–45 *LED connectors are designed to mate with .014–.020 [0.36–0.51] diameter posts or square leads. 1 Other circuit sizes are available upon request. Minimums may apply. 2 Tape mounted. Note: :Blocked circuit configurations are available. Contact product engineer or product manager for details. Minimums may apply. MTA, CST-100 II and SL-156 Connectors Closed End Strain Relief Covers MTA-100 IDC Connector Accessories Covers Closed End Dust Covers .345 [8.76] .127 [3.23] .340 Closed End Strain Relief Covers A Material (RoHS Compliant) Strain Relief Cover—UL94V-2 rated, nylon, white Closed End Dust Covers [8.64] .360 [9.14] .345 [8.76] .127 [3.23] .335 [8.51] Retention Dimple .340 [8.64] A Dust Covers—UL94V-0 rated, polyester, white .105 [2.67] .335 [8.51] Retention Dimple .130 [3.3].360 A [9.14] Note: This portion of the front locking bar may or may not be present. Cover Ordering Information .105 [2.67] .130 [3.3] A Note: This portion of the front locking bar may or may not be present. Strain Relief Covers The “Base Part Numbers” Chart at Feed-Thru right .127 shows the base part number and number [3.23] .360 of circuits available for the described [9.14] Feed-Thru Strain Relief Covers cover. Prefixes and suffixes are determined by the number of circuit positions in the cover. For example, the complete part number for a 10-position closed end strain relief cover would be: .127 [3.23] A Feed-Thru Dust Covers Retention Dimple Feed-Thru Dust Covers .360 [9.14] Retention Dimple A .245 [6.22] .245 [6.22] .395 [10.03] .395 [10.03] A Base number 643075 plus prefix-and-suffix 1- — -0 The correct ordering number is 1-643075-0 .130 [3.3] A Note: This portion of the front locking bar may or may not be present. .130 [3.3] Note: This portion of the front locking bar may or may not be present. Base Part Numbers Base PartClosed Numbers End Feed-Thru ClosedDust End Feed-Thru Dust Strain Relief Strain Relief Strain Relief Dust Covers Strain Relief Covers Dust Covers Covers Covers Covers Covers Covers Cover No. of Cover No. of Cover No. of Cover No. of Cover No.Part of Nos. Cover CoverCircuits No. of PartCover No. of Part Nos. Circuits CircuitsNo. of Part Nos. Nos. Circuits Part Nos. Circuits Part Nos. Circuits Part Nos. Circuits Part Nos. Circuits 643075 2–28 640550 2–28 643077 2–28 640642 3-28 643075 2–28 640550 2–28 643077 2–28 640642 3-28 Cover Length Cover Length No. of Circuits 2 3 4 5 6 7 8 PAGE 9 No. of Dim. Dim.Circuits Prefix/ A A Suffix .200 2 5.08 .200 -2 5.08 3 .300 7.62 .300 -3 .400 7.62 4 10.16 .400 .500 -4 10.16 5 12.7 .500 .600 -5 12.7 6 15.24 .700 .600 7 -6 17.78 15.24 .800 .700 8 -7 20.32 17.78 .800 -8 20.32 Prefix/ No. of Suffix Circuits -2 9 -3 10 -4 11 -5 12 -6 -7 13 -8 14 15 No. of Dim. Circuits A 9 .900 22.86 10 1.00 25.4 11 1.100 12 27.94 1.200 13 30.48 1.300 14 33.02 1.400 15 35.56 1.500 38.1 Dim. Prefix/ A Suffix .900 22.86 -9 1.00 25.4 1- -0 1.100 27.94 1.200 1- -1 30.48 1.300 1- -2 33.02 1.400 1- -3 35.56 1.500 1- -4 38.1 1- -5 Prefix/ No. of No. of Circuits Dim. Suffix Circuits -9 16 1- -0 1- -1 1- -2 17 18 1- -3 19 1- -4 20 1- -5 21 22 Dim. Prefix/ A Prefix/ Suffix A 1.600 16 1.600 40.64 40.64 1.700 17 1.700 43.18 1843.18 1.800 45.72 1.800 1945.72 1.900 48.26 1.900 2.000 20 48.26 50.8 2.000 2.100 21 50.8 53.34 2.100 2.200 22 53.34 55.88 2.200 55.88 No. of Dim. No.Circuits of Dim.A Circuits A 2.300 23 1- -6 58.42 2.300 23 1- -6 58.42 2.400 24 1- -7 60.96 2.400 24 1- -7 2.500 60.96 25 1- -8 63.5 25 26 2.500 2.600 1- -8 1- -9 63.5 66.04 2.700 26 27 2.600 1- -9 2- -0 66.04 68.58 2.800 27 28 2.700 2- -0 2- -1 71.12 68.58 2.800 28 2- -1 2- -2 71.12 Suffix 2- -2 Prefix/ Prefix/ Suffix Suffix 2- -3 2- -3 2- -4 2- -4 2- -5 2-2--5 -6 2-2--6 -7 -8 2-2--7 2- -8 MTA, CST-100 II and SL-156 Connectors MTA-100 IDC Connector Accessories (continued) Keying Plug with Carrier Strip (10 plugs per strip) Part No. 641994-1 .027 Sq. [0.69] Material (RoHS Compliant) UL94V-2 rated, nylon, natural color .038 [0.97] .300 [7.62] .065 [1.65] .077 [1.96] Note: Removal of contact is not necessary when using keying plug. .125 [3.18] .500 Ref. [12.7] 1.800 Ref. [45.72] Replacement IDC Contacts Material and Finish Phosphor bronze, post tin plated; .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel Wire Size AWG mm2 22 24 26 28 0.3–0.4 0.2 0.12–0.15 0.08–0.09 Part Numbers Standard .000030 [0.00076] .000015 [0.00038] Tin Plated Gold Plated Gold Plated 640636-3 641186-4 641186-3 640637-3 641187-4 641187-3 640638-3 641188-4 641188-3 640639-3 641189-4 641189-3 Note: TE does not recommend terminating an MTA contact more than one time. Use replacement contacts when required for field repairs or wire changes. 2 .452 [11.48] Crimp Snap-In Contacts Material and Finish Phosphor bronze, tin plated. .142 [3.61] Max. .070 [1.78] .075 [1.91] Wire Size Part Nos. AWG mm2 Loose Piece* Strip** 26-22 0.12–0.4 640709-2 640708-2 *Hand Tool No. 59836-1 (IS 408-6527) **Applicator No. 466747-1 (IS 408-8040) .425 [10.8] .070 [1.78] Special applications for crimp snap-in contacts are: 1. Double wire per contact 2. Coax or shielded wire 3. Mixed wire size in same connector Note: Only one crimp snap-in contact per connector. PAGE 10 LED Tin Plated 641643-2 641644-2 641645-2 641646-2 MTA, CST-100 II and SL-156 Connectors MTA-100 Connector/Connector Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. 647 000 647 001 647 002 647 003 647 004 647 005 647 006 647 007 Posted Connectors Connectors Matrix for Tin Plated Part Numbers 640440 640441 640442 640443 640468 640469 640470 640471 640620 640621 640622 640623 641311 641312 641313 641314 641534 641535 641536 641537 641653 641654 641655 641656 643498 643813 643814 643815 643816 643828 644083 644312 644313 644497 644511 644512 644513 644514 644540 644563 644564 644565 644574 644575 644576 644577 644578 644579 644795 1375820 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y Y Y Y Y* Y* Y* N *2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100 connectors with polarizing tabs. PAGE 11 MTA, CST-100 II and SL-156 Connectors MTA-100 Connector/Connector Mateability Guide (continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-100 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.00076] Gold Plated Part Numbers Connectors 647 008 647 009 647 010 647 011 647 012 647 013 647 014 647 015 Posted Connectors 641237 641238 641239 641240 641241 641242 641243 641244 644020 644042 644043 644044 644702 644726 1375820 Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* N N Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* N *2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100 connectors with polarizing tabs. Matrix for .000015 [0.00038] Gold Plated Part Numbers Connectors 647 008 647 009 647 010 647 011 647 012 647 013 647 014 647 015 Posted Connectors 641190 641191 641192 641193 641198 641199 641200 641201 644038 644040 647477 644726 647480 1375820 1744020 Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* Y* Y* Y* Y* Y* N N Y Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y Y Y Y Y Y Y Y Y Y* Y* Y* Y* Y* N Y *2 & 3 position MTA-100 Posted Connectors can not mate with MTA-100 connectors with polarizing tabs. PAGE 12 MTA, CST-100 II and SL-156 Connectors MTA-100 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru Material and Finish Closed End Feed-Thru Housing—UL94V-2 rated, nylon, see chart for color Contacts—Copper alloy, post tin or gold plated over nickel (see chart) B Dim. Note: 1. Mating half visuals — pages 7 & 8. 2. Use feed thru strain relief covers & feed thru dust covers (if needed)—page 9. 3. Approved wire listing—pages 52-56. .025 Sq. [0.54] .843 [21.40] .079 [2.00] A Dim. B Dim. .079 [2.00] A Dim. .025 Sq. [0.54] .303 [7.70] .303 [7.70] .415 [10.54] .415 [10.54] Connector Ordering Information .100 Typ. [2.54] The “Base Part Numbers” Chart at right shows the base part number. Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 12-position closed end connector for 22 AWG wire would be: Base number 647000 plus prefix-and-suffix 4- — -2 The correct ordering number is 4-647000-2 All part numbers are the RoHS equivalent version. Example: No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-647000-2 thru 19 4-647000-9 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Color Coding by Wire Size for UL94V-2 Connectors 22 AWG—Red 24 AWG—White 26 AWG—Blue 28 AWG—Green Performance Data Voltage Rating—250 vac Current Rating—5 amp max. Low-Level Resistance—6 mΩ max. initial Dielectric Withstanding Voltage— 750 vac/1 min. Insulation Resistance—5000 MΩ min. initial Operating Temperature—-55° C to +105° C PAGE 13 .100 Typ. [2.54] Base Part Numbers Connector Type & Wire Size Closed End Connector RoHS Equiv. Part Nos. 647000 32–49 1 647004 —2 647001 32–49 1 647005 —2 647002 32–49 1 647006 —2 647003 32–49 1 647007 —2 26 AWG 0.12–0.15 mm2 28 AWG 0.08–0.09 mm 2 Standard UL 94V-2, .000030 [0.00076] Gold Plated 22 AWG 647008 0.3–0.4 mm2 24 AWG 647009 2 0.2 mm 26 AWG 0.12–0.15 mm 2 28 AWG 0.08–0.09 mm 2 647010 647011 Standard UL 94V-2, .000015 [0.00038] Gold Plated 22 AWG 647016 0.3–0.4 mm2 24 AWG 647017 0.2 mm 2 26 AWG 647018 0.12–0.15 mm 2 28 AWG 0.08–0.09 mm 2 2 Feed-Thru Connector Part Nos. Standard UL 94V-2, Tin Plated 22 AWG 0.3–0.4 mm 2 24 AWG 0.2 mm 2 1 .843 [21.40] 32–49 1 647012 —2 32–49 1 647013 —2 32–49 1 647014 —2 32–49 1 647015 —2 32–49 1 647020 —2 32–49 1 647021 —2 32–49 1 647022 —2 1 647023 —2 32–49 647019 No. of Circuits 2 and 3 position MTA-100 Posted Connectors (Closed End) can not mate with MTA-100 connectors with polarizing tabs. Parts may be manufactured upon request. Minimums may apply. Contact product engineer or product manager for details. No. of Circuits Dim. 3 A .300 [7.62] .400 [10.16] 4 .500 .427 [12.70] [10.85] 5 .600 .527 [15.24] [13.39] 2 B .227 [5.77] .327 [8.31] No. of Circuits Dim. 7 A B .700 .627 [17.78] [15.93] .800 .727 [20.32] [18.47] 8 .900 .827 [22.86] [21.01] 9 1.000 .927 [25.40] [23.55] 6 No. of Circuits Dim. No. of Circuits 11 15 A B 1.500 1.427 [38.10] [36.25] 1.600 1.527 [40.64] [38.79] 12 1.300 1.227 [33.02] [31.17] 16 1.700 1.627 [43.18] [41.33] 13 1.400 1.327 [35.56] [33.71] 17 1.800 1.727 [45.72] [43.87] 10 14 18 19 Technical Documents Product Specification 108-1050-1 MTA-100 Posted Connector Application Specification 114-1019 MTA-100 Connectors Replacement IDC Contacts Material and Finish Contacts—Copper alloy, post tin or gold plated over nickel Wire Size AWG mm 2 .075 [1.91] .083 [2.10] Dim. A B 1.100 1.027 [27.94] [26.09] 1.200 1.127 [30.48] [28.63] .770 [19.55] .025 [0.64] 1.900 1.827 [48.26] [46.41] 2.000 1.927 [50.80] [48.95] Part Numbers Tin .000030 Plated [.00076] Gold Plated 3-647030-1 3-647030-2 22 0.3-0.4 0.2 3-647031-1 3-647031-2 24 26 0.12-0.15 3-647032-1 3-647032-2 28 0.8-0.9 3-647033-1 3-647033-2 MTA, CST-100 II and SL-156 Connectors MTA-100 Flat Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Right-Angle Post (.025 [0.64] Square) Housing—UL94V-0 rated, polyester, white Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. Post No. 1 .200 [5.08] A .025 [0.64] Sq. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. .200 [5.08] .100 [2.54] .050 Typ. [1.27] Typ. Post No. 1 .100 [2.54] .295 [7.49] .140 [3.56] Ref. .100 [2.54] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. .025 [0.64] Sq. Header Ordering Information No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-641211–2 thru 28 5-641211-8 .050 [1.27] Typ. X= .120 [3.05] min., when mated with CST-100 II Connector. Edge of Board .120 [3.05] Min. .050/.040 Dia. [1.27/1.02] .100 [2.54] Typ. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Edge of Board .050/.040 Dia. [1.27/1.02] .100 Typ. [2.54] X Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Straight Posts Header No. of Posts/ Part Nos. RoHS Equiv. Right-Angle Posts Header No. of Posts/ Part Nos. RoHS Equiv. See page 8 for an explanation of RoHS lead free equivalents. Standard UL94V-0, Tin Plated 640452 2–28 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Standard UL94V-0, .000030 [0.00076] Gold Plated 2–28 641211 641212 32–58 2–28 32–58 Standard UL94V-0, .000015 [0.00038] Gold Plated 2–28 641122 641123 32–58 2–28 32–58 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 14 .295 [7.49] .100 [2.54] Typ. X= .120 [3.05] min., .240 [6.1] max. when mated with MTA-100 Connector. The “Base Part Numbers” Chart at right shows the base part number. Base number 641211 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641211-0 All part numbers are the RoHS equivalent version. Example: .062 [1.57] .140 [3.56] Ref. .535 [13.59] 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: A 640453 2–28 MTA, CST-100 II and SL-156 Connectors MTA-100 Narrow Flat Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Right-Angle Post (.025 [0.64] Square) Housing—UL94V-0 rated, polyester, white Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel .110 [2.79] Ref. Notes: .0335 [0.85] 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Headers without retentive legs are suitable for breakaway application. 3. 2 or 3 retentive leg(s) per header, depending upon number of positions. 4. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. .092 [2.34] A A .092 [2.34] .100 [2.54] Typ. .100 [2.54] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. .295 [7.49] .505 [12.83] .044 [1.12] Typ. .025 [0.64] Sq. .150 [3.81] .100 [2.54] Typ. Post No. 1 5. To determine header overall length (dim. A) multiply .100 x the number of posts minus (–) .012. Example: .100 x 10 posts – .012 = .988 inches [25.1 mm]. Straight and Right-Angle Post with Retentive Legs .260 [6.6] Post No. 1 .100 [2.54] .044 [1.12] Typ. .025 [0.64] Sq. .110 [2.79] Ref. .110 Ref. [2.79] Connector Ordering Information The “Base Part Numbers” Chart at right shows the base part number. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts and without retentive legs would be: Base number 644456 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-644456-0 All part numbers are the RoHS equivalent version. Example: No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-644456–2 thru 28 5-644456-8 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 15 .100 [2.54] Typ. Edge of Board .060 [1.52] Min. .050/.040 Dia. [1.27/1.02] For Straight Leg Headers .060 .037 ± .002 [1.52] Dia. [0.94±0.05] Min. For Retentive Leg Headers Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board .100 [2.54] Typ. Edge of Board .050/.040 Dia. [1.27/1.02] For Straight Leg Headers .037 ± .002 Dia. [0.94± 0.05] For Retentive Leg Headers Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Straight Posts Without With Retentive Legs Retentive Legs RoHS Header RoHS Header Part Nos. Equiv. Part Nos. Equiv. Standard UL94V-0, Tin Plated 644456 32–58 644695 32–58 Right-Angle Posts Without With Retentive Legs Retentive Legs Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 644457 32–58 644694 32–58 Standard UL94V-0, .000030 [0.00076] Gold Plated 644884 2–28 644886 2–28 644885 2–28 644887 2–28 Standard UL94V-0, .000015 [0.00038] Gold Plated 644888 2–28 644890 2–28 644889 2–28 644891 2–28 High temperature product available. Please contact Sales Engineer or Product Information Center. MTA, CST-100 II and SL-156 Connectors MTA-100 Polarized Headers—Straight and Right-Angle Material and Finish Housing—UL94V-0 rated, polyester, white Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Straight Post (.025 [0.64] Square) .225 [5.72] .225 [5.72] Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. All posts on retentive leg headers are bent. 4. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. A .025 [0.64] Sq. A .100 [2.54] Typ. Post No. 1 .295 [7.49] .535 [13.59] PAGE 16 .295 [7.49] .100 [2.54] .140 Max. [3.56] .125 [3.18] Ref. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. .035 Min. [0.89] .290 [7.37] .140 [3.56] .100 [2.54] The “Base Part Numbers” Chart at right shows the base part number. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Post No. 1 .290 [7.37] .140 [3.56] Ref. Connector Ordering Information See page 8 for an explanation of RoHS lead free equivalents. .100 [2.54] Typ. .050 [1.27] Typ. .025 [0.64] Sq. .035 [0.89] Min. .050 [1.27] Typ. For mating half visuals, see pages 7, 8 and 24. No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-641213–2 thru 28 5-641213-8 .125 [3.18] .125 [3.18] For mateability options, see matrix on pages 5 and 6. Base number 641213 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641213-0 All part numbers are the RoHS equivalent version. Example: Right-Angle Post (.025 [0.64] Square) 34° .135 Ref. [3.43] 34° Retentive Leg Edge of Board .050/.040 Dia. for straight [1.27/1.02] leg headers .037 ± .002 Dia. for retentive [0.94 ± 0.05] leg headers .100 [2.54] Typ. .130 [3.30] Min. Retentive Leg Edge of Board X Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board .050/.040 Dia. for straight [1.27/1.02] leg headers .037 ± .002 Dia. for retentive [0.94 ± 0.05] leg headers .100 [2.54] Typ. X= .110 [2.79] min., .160 [4.06] max. when mated with MTA-100 Connector. X= .110 [2.79] min., .120 [3.05] max. when mated with CST-100 II Connector. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Straight Posts Without With Retentive Legs Retentive Legs Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. Standard UL94V-0, Tin Plated 640454 2–28 644876 2–28 Right-Angle Posts Without With Retentive Legs Retentive Legs Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 640455 2–28 644877 Standard UL94V-0, .000030 [0.00076] Gold Plated 641213 32–58 — — 2–28 641214 32–58 — — Standard UL94V-0, .000015 [0.00038] Gold Plated 641124 32–58 — — 641125 32–58 — — MTA, CST-100 II and SL-156 Connectors MTA-100 Friction Lock Headers—Straight and Right-Angle Material and Finish Housing—UL94V-0 rated, polyester, white Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Straight Post (.025 [0.64] Square) .225 [5.72] .225 [5.72] Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. All posts on retentive leg headers are bent. 4. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. A .025 [0.64] Sq. A .100 [2.54] Typ. Post No. 1 .295 [7.49] .535 [13.59] PAGE 17 .295 [7.49] .100 [2.54] .140 Max. [3.56] .125 [3.18] Ref. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. Post No. 1 .290 [7.37] .035 Min. [0.89] .290 [7.37] .140 [3.56] .100 [2.54] The “Base Part Numbers” Chart at right shows the base part number. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Sq. .140 [3.56] Ref. Header Ordering Information See page 8 for an explanation of RoHS lead free equivalents. .100 [2.54] Typ. .050 [1.27] Typ. .025 .035 [0.89] Min. .050 [1.27] Typ. For mating half visuals, see pages 7, 8 and 24. Lead Free No. of Standard RoHS Pos. Prefix/Suffix Prefix/Suffix 2 641215–2 3-641215–2 thru 28 2-641215-8 5-641215-8 .125 [3.18] .125 [3.18] For mateability options, see matrix on pages 5 and 6. Base number 641215 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641215-0 All part numbers are the RoHS equivalent version. Example: Right-Angle Post (.025 [0.64] Square) 34° .135 Ref. [3.43] 34° Retentive Leg Edge of Board .050/.040 Dia. for straight [1.27/1.02] leg headers .037 ± .002 Dia. for retentive [0.94 ± 0.05] leg headers .100 [2.54] Typ. .130 [3.30] Min. Retentive Leg Edge of Board X Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board .050/.040 Dia. for straight [1.27/1.02] leg headers .037 ± .002 Dia. for retentive [0.94 ± 0.05] leg headers .100 [2.54] Typ. X= .110 [2.79] min., .160 [4.06] max. when mated with MTA-100 Connector. X= .110 [2.79] min., .120 [3.05] max. when mated with CST-100 II Connector. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Straight Posts Without With Retentive Legs Retentive Legs Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. Standard UL94V-0, Tin Plated 640456 2–28 644874 2–28 Right-Angle Posts Without With Retentive Legs Retentive Legs Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 640457 2–28 644875 Standard UL94V-0, .000030 [0.00076] Gold Plated 641215 32–58 — — 2–28 641216 32–58 — — Standard UL94V-0, .000015 [0.00038] Gold Plated 641126 32–58 — — 641127 32–58 — — MTA, CST-100 II and SL-156 Connectors MTA-100 Headers with Retention Peg—Straight Material and Finish Friction Lock .113 [2.87] Housing—UL94V-0 rated, thermoplastic, black Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. .250 [6.35] A .025-.040 [0.64-1 .01] Post No 1 . .135 [3.43] .025 ± .001 [0.64 ± 0.03] Square Typ. .1 25 [3.1 8] .1 00 Typ. [2.54] .290 ± .010 ] [7.37 ± 0.25] .347 ± .010 .550 ± .010 [8.81 ± 0.25] [13.97± 0.25] .070 [1 .78] .050 [1 .27] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. Polarized .113 [2.87] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: Post No. 1 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 18 .290 ± .010 .135 [7.37 ± 0.25] [3.43] .025 ± .001 [0.64 ± 0.03] Square Typ. .125 [3.18] .100 Typ. [2.54] Base number 647609 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647609-0 All part numbers are the RoHS equivalent version. Example: Lead Free No. of Standard RoHS Pos. Prefix/Suffix Prefix/Suffix 2 647609-2 3-647609-2 3 647609-3 3-647609-3 4 647609-4 3-647609-4 5 647609-5 3-647609-5 6 647609-6 3-647609-6 7 647609-7 3-647609-7 8 647609-8 3-647609-8 9 647609-9 3-647609-9 10 1-647609-0 4-647609-0 11 1-647609-1 4-647609-1 12 1-647609-2 4-647609-2 .055 Min. [1.39] .250 [6.35] A .055 [1.40] .070 [1.78] .050 [1.27] .100 Typ. [2.54] Ø .052 ± .002 [1.32 ± 0.05] .347 ± .010 .550 ± .010 [8.81 ± 0.25] [13.97± 0.25] .070 Min. [1.78] .090 [2.29] Ø.040 ± .003 [1.02± 0.07] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Friction Lock Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647609 32-42 Polarized Header RoHS Part Nos. Equiv. 647623 32-42 Standard UL94V-0, .000030 [0.00076] Gold Plated 647626 32-42 647624 32-42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647627 32-42 647625 32-42 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. MTA, CST-100 II and SL-156 Connectors MTA-100 High Profile Headers—Right-Angle Material and Finish Housing—UL94V-0 rated, thermoplastic, black Contacts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. 4. This product can be mounted in the middle of the PC Board as shown in the PCB layout. Friction Lock Right-Angle Post (.025 [0.64] Square) A .250 [6.35] .250 [6.35] .113 [2.87] .113 [2.87] A .025 [0.64] Sq. .040 [1.02] Max. Post No. 1 .290 [7.37] .100 [2.54] .050 [1.27] .025 [0.64] Sq. .100 [2.54] .070 [1.78] .050 [1.27] .290 Post No. 1 [7.37] .347 [8.81] .112 [2.84] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. Polarized Right-Angle Post (.025 [0.64] Square) .112 [2.84] .125 [3.18] .347 [8.81] .140 [3.56] .125 [3.18] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number. .100 Typ. [2.54] Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with right-angle posts would be: Base number 647630 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647630-0 All part numbers are the RoHS equivalent version. Example: No. of Pos. 2 3 4 5 6 7 8 9 10 11 12 Lead Free RoHS Prefix/Suffix 3-647630-2 3-647630-3 3-647630-4 3-647630-5 3-647630-6 3-647630-7 3-647630-8 3-647630-9 4-647630-0 4-647630-1 4-647630-2 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 19 .040 ± .003 Dia. [1.02 ± 0.07] Note: Consult Product Drawing for details on placing headers onto PC boards. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Base Part Numbers Friction Lock Right-Angle Posts Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647630 32-42 Polarized Right-Angle Posts Header RoHS Part Nos. Equiv. 647651 32-42 Standard UL94V-0, .000030 [0.00076] Gold Plated 647629 32-42 647653 32-42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647628 32-42 647652 32-42 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. MTA, CST-100 II and SL-156 Connectors MTA-100 Polarized High Temperature Headers—Straight and Right-Angle Material and Finish Housing— 2–12 Position—UL94V-0 rated, nylon, black 13–18 Position—UL94V-0 rated, LCP, black Posts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel For use with Infrared Reflow Process Straight Post (.025 [0.64] Square) 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. Right-Angle Post (.025 [0.64] Square) A .250 [6.35] .250 [6.35] .113 [2.87] Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. Maximum Temperature 2–12 Position: 280°C 13–18 Position: 235°C Rating: .113 [2.87] A .025 [0.64] Sq. .100 [2.54] .070 [1.78] .050 [1.27] Post No. 1 .290 [7.37] For mating half visuals, see pages 7, 8 and 24. .100 [2.54] .125 [3.18] .112 [2.84] .135 [3.43] Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: Base number 647047 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647047-0 All part numbers are the RoHS equivalent version. Example: No. of Pos. 2 12 13 18 Lead Free RoHS Prefix/Suffix 3-647047-2 thru 4-647047-2 NA thru NA See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 20 .060 [1.52] Pre-Tinned Land Both Sides Typ. .347 [8.81] .140 [3.56] .125 [3.18] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number. .070 [1.78] .050 [1.27] .290 Post No. 1 [7.37] .347 [8.81] .550 [13.97] For mateability options, see matrix on pages 5 and 6. .025 [0.64] Sq. .008 [0.20] Min. Thk. Solder Paste In Area Shown .100 [2.54] Typ. Post No. 1 .040 [1.02] Pre-Tinned Plated Thru Hole Typ. .300 [7.62] .150 [3.81] Note: Consult Product Drawing for details on placing headers onto PC boards. .0325 [0.826] .065 [1.65] Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board Base Part Numbers Straight Posts Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647047 32–42 Straight Posts (Tube Loaded) Header RoHS Part Nos. Equiv. Right-Angle Posts Header RoHS Part Nos. Equiv. 32–42 647048 32–42 Standard UL94V-0, .000030 [0.00076] Gold Plated 647109 32–42 647300 32–42 647114 32–42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647075 32–42 647299 32–42 647076 32–42 647298 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. MTA, CST-100 II and SL-156 Connectors MTA-100 Friction Lock High Temperature Headers—Straight and Right-Angle Material and Finish Housing— 2–12 Position—UL94V-0 rated, nylon, black 13–18 Position—UL94V-0 rated, LCP, black Posts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. For use with Infrared Reflow Process Straight Post (.025 [0.64] Square) Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts would be: Base number 647050 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647050-0 All part numbers are the RoHS equivalent version. Example: Lead Free No. of Standard RoHS Pos. Prefix/Suffix Prefix/Suffix 2 647050-2 3-647050-2 thru 12 1-647050-2 4-647050-2 13 1-647050-3 NA thru 18 1-647050-8 NA See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 21 Right-Angle Post (.025 [0.64] Square) .250 [6.35] .250 [6.35] .113 [2.87] .113 [2.87] A .025 [0.64] Sq. .040 [1.02] Max. Post No. 1 .290 [7.37] .050 [1.27] .100 [2.54] .130 [3.30] .125 [3.18] .060 [1.52] Pre-Tinned Land Both Sides Typ. A .040 [1.02] Max. .025 Sq. Post No. 1 .290 [7.37] .347 [8.81] .550 [13.97] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. Maximum Temperature 2–12 Position: 280°C 13–18 Position: 235°C Rating: .347 [8.81] .112 [2.84] .050 [1.27] .100 [2.54] .125 [3.18] .008 [0.20] Min. Thk. Solder Paste In Area Shown .100 [2.54] Typ. Post No. 1 .040 [1.02] Pre-Tinned Plated Thru Hole Typ. .300 [7.62] .150 [3.81] Note: Consult Product Drawing for details on placing headers onto PC boards. .0325 [0.826] .065 [1.65] Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board Base Part Numbers Straight Posts Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647050 32–42 Straight Posts (Tube Loaded) Header RoHS Part Nos. Equiv. Right-Angle Posts Header RoHS Part Nos. Equiv. 32–42 647051 32–42 Standard UL94V-0, .000030 [0.00076] Gold Plated 647116 32–42 647297 32–42 647117 32–42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647078 32–42 647296 32–42 647079 32–42 647295 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. MTA, CST-100 II and SL-156 Connectors MTA-100 Polarized and Friction Lock Surface Mount Headers—Straight Material and Finish Housing— 2–12 Position—UL94V-0 rated, nylon, black 13–18 Position—UL94V-0 rated, LCP, black Posts—Copper alloy, tin plated, .000030 [0.00076] or .000015 [0.00038] gold over nickel Note: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. To determine header overall length (dim. A) multiply .100 x the number of posts. Example: .100 x 10 posts equals 1.000 inch [25.4 mm]. For use with Infrared Reflow Process Maximum Temperature 2–12 Position: 280°C 13–18 Position: 235°C Rating: Polarized Header Friction Lock Header .113 [2.87] .318 [8.08] Ref. .113 [2.87] .318 [8.08] Ref. .250 [6.35] .025 [0.64] Sq. .290 [7.37] .100 [2.54] .050 .125 [1.27] [3.18] .290 [7.37] .159 [4.04] Typ. .100 [2.54] See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. .159 [4.04] .060 [1.52] Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position surface mount polarized header would be: Lead Free RoHS Prefix/Suffix 3-647106-2 4-647106-2 .125 [3.18] Post No. 1 The “Base Part Numbers” Chart at right shows the base part number. No. of Pos. 2 12 .050 [1.27] .347 [8.81] .100 [2.54] Typ. Header Ordering Information Base number 647106 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647106-0 All part numbers are the RoHS equivalent version. Example: .040 [1.02] Max. Post No. 1 .347 [8.81] For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. .025 [0.64] Sq. .070 [1.78] Post No. 1 .250 [6.35] .235 [5.97] Note: Consult Product Drawing for details on placing headers onto PC boards. .070 [1.78] Recommended PC Board Layout for use with .010 [0.25] Thick Stencil Base Part Numbers Polarized Headers Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647106 32-42 Friction Lock Headers Header RoHS Part Nos. Equiv. 647166 32-42 Standard UL94V-0, .000030 [0.00076] Gold Plated 647108 32-42 647168 32-42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647107 32-42 647167 32-42 Tape Mount Part Numbers Polarized Headers Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647531 32-42 Friction Lock Headers Header RoHS Part Nos. Equiv. 647502 32-42 Standard UL94V-0, .000030 [0.00076] Gold Plated 1744163 32-42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647467 32-42 Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 22 MTA, CST-100 II and SL-156 Connectors Right-Angle (.025 [0.64] Square) Straight Post (.025 [0.64] Square) MTA-100 Shrouded Headers—Straight and Right-Angle Post No. 1 Post No. 1 Material and Finish Right-Angle (.025 [0.64] Square) Straight Post (.025 [0.64] Square) A Housing—UL94V-0 rated, polyester, black Posts—Copper alloy, tin plated, .000030 [0.00076] gold over nickel A Post No. 1 Notes: Post No. 1 .313 [7.95] A 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. .313 [7.95] A .410 [10.41] 2. Headers with .000015 [0.00038] gold plated post are available upon request. Minimums may apply. .200 .410 [10.41] .313 [5.08] [7.95] .440 [11.18] 3. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. .025 [0.64] Typ. For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 7, 8 and 24. .092 [2.34] Typ. Ref. .100 [2.54] .025 [0.64] Typ. Header Ordering Information .410 [10.41] .140 [3.56] .025 .200 [0.64] .125 [5.08]Typ. .440 [3.18] [11.18] .176 [4.47] .140 Ref. .107 [2.72] .092 [3.56] Ref. .100 [2.54] [2.34] Typ. Ref. .107 [2.72] Ref. .125 [3.18] .092 .130 .410 [2.34] [3.30] [10.41] Typ. Ref. .137 [3.48] Ref. .092 .130 .100 [2.54] .025 [0.64] Typ. .176 [4.47] Ref. Ref. Base number 644486 plus .100 prefix-and-suffix .050/.040 Dia. [2.54] [1.27/1.02] .100 .050/.040 4- — -0 Typ.Dia. [2.54] [1.27/1.02] The correct ordering number is Typ. .081/.075 Dia. 4-644486-0 [2.06/1.91] .081/.075 Dia. No. of Header Length Circuits No. of Circuits 2 3 4 5 PAGE 23 Dim. A .284 7.21 .384 9.75 .484 12.29 .584 14.83 2 3 4 5 Dim. A .284 Prefix/ 7.21 Suffix .384 9.75 3- -2 .484 12.29 3- .584 -3 14.83 .206 [5.23] Ref. [7.62] Max. Edge of Board .042 [1.07] .124 [3.15] .130 [3.30] Ref. .130 [3.30] Ref. Rear Bend Rear Bend .124 [3.15] .050/.040 Dia. [1.27/1.02] .050/.040 .100 [2.54] .100 Dia. Typ. [1.27/1.02] [2.54] Note: Consult Product Drawing Note: Consult Product headers Drawing for details on placing for details on placing headers onto PC boards. Typ. onto PC boards. [2.06/1.91] Recommended Mounting Hole Pattern forRecommended Mounting Hole Pattern for .062 Recommended Mounting Hole Pattern forRecommended Mounting Hole Pattern for .062 .062 [1.57].062 Thk.[1.57] PC Board [1.57] Thk.Thk. PC PC Board Thk. PC Board [1.57] Board (Solder Side of Board (Solder SideSide of Board Shown) (Solder Side Shown) of Board Shown) (Solder of Board Shown) Part Numbers Base PartBase Numbers Straight Posts Straight Posts With Pegs With Pegs Header Without WithoutPegs RoHS Pegs Header RoHS Nos. Equiv. Header Part RoHS HeaderPart Nos. RoHS Equiv. Part Nos. Equiv. Part Nos. Equiv. Standard UL94V-0, Tin Plated Right-Angle Posts Right-Angle Posts Without Pegs Only Without Pegs Only Front Bend Rear Bend Front BendRoHS Rear Bend Header Header RoHS Part Nos. RoHS Equiv. Part Nos. Equiv. Header Header RoHS Part Nos. Equiv. Part Nos. Equiv. 644486 22-34 644861 22-34 644488 22-34 Standard UL94V-0, Tin Plated 644486 22-34 644861[0.00076] 22-34 22-34 Standard UL94V-0, .000030 Gold Plated644488 644487 Header Length .206 [5.23] Ref. Front Bend Polarized Retention Peg.300 [7.62] Max. .300 Edge of Board .042 [1.07] Edge of Board Notes: 1. Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. 2. MTA-100 shrouded headers do not mate with CST-100 II housings. Max. .176 Polarized Retention Peg Prefixes and suffixes are determined by the number of post positions in the head.125 er. For example, the complete part num[3.18] Min. ber for a 10-position header with straight .125 Edge of Board [3.18] posts and with pegs would be: Min. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. .050 .200 [1.27] [5.08] .050 [2.34] [3.30] Ref. [1.27] Typ. Ref. .137 Max. [3.48] Front Bend .176 Ref. .100 [2.54] The “Base Part Numbers” Chart at right shows the base part number. See page 15 for an explanation of RoHS lead free equivalents. .200 [5.08] .313 [7.95] 22-34 — — Standard UL94V-0, .000030 [0.00076] Gold Plated 644487 22-34 — — Prefix/ Suffix No. of Circuits 3- -2of No. Circuits 6 Dim. A 7 .684 17.37 8 .784 19.91 9 .884 22.45 .984 24.99 3- -3 6 3- -4 7 3- -5 3- -4 8 3- -5 9 22-34 644489 644489 22-34 Dim. Prefix/ No. of Dim. Prefix/ A Suffix Circuits A Suffix .684 1.084 3-6 10 4- -0 Prefix/ No. of Dim. Prefix/ 17.37 27.53 Suffix Circuits A Suffix .784 1.184 3- -7 11 4- -1 19.91 1.08430.07 4- -0 10 3- -6 27.531.284 .884 3- -8 12 4- -2 22.45 1.184 32.61 3- -7 11 4- -1 .984 1.384 30.07 3- -9 13 4- -3 24.99 35.15 3- -8 12 3- -9 13 1.284 32.61 1.384 35.15 4- -2 4- -3 644803 644803 — — No. of Circuits No. 14 of Circuits 14 Dim. A 1.484 Dim. 37.69 A 1.484 37.69 22-34 22-34 — — Prefix/ Suffix 4- -4 Prefix/ Suffix 4- -4 MTA, CST-100 II and SL-156 Connectors .100 [2.54] Centerline CST-100 II Crimp Contacts and Housings PRODUCT FACTS • • • • • • • • • Low cost wire-to-board interconnections Wide wire range for single contact Tin and gold plated contacts Mates with specified MTA and similar competitive notched headers Plastic latching feature in housing helps prevent contact backout Locking ramps and polarizing tabs are standard For keying purposes use keying plug 641994-1 (page 10) Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR7189 For mateability options, see matrix on pages 5 and 6. For mating half visuals, see pages 13 thru 23 and 25. See page 8 for an explanation of RoHS lead free equivalents. Contacts Tin Plated 1375819-1 (Strip) Part Numbers 15 Au Gold Plated 1375819-2 (Strip) .195 [4.95] 30 Au Gold Plated 1375819-3 (Strip) Performance Data 1445336-1 (Loose Piece) 1445336-2 (Loose Piece) 1445336-3 (Loose Piece) Voltage Rating—250 vac Material and Finish (RoHS Compliant) Current Rating—4 amp max. Phosphor bronze, pretinned or .000015 [.00038] gold, over nickel .000030 [0.00076] gold over nickel Wire Range —22–26 AWG [0.35–0.13 mm2] Max. Ins. Dia. — .065 [1.65] Low-Level Resistance— 6 mΩ max. initial; 10 mΩ max. initial Dielectric Withstanding Voltage— 750 vac/1 min. Insulation Resistance—1000 MΩ min. initial; 100 MΩ min. final Operating Temperature— -55° C to +105° C Material (RoHS Compliant) UL94V-0 rated, nylon, white No. of Pos. 2 Product Specification 108-1948 3 Instruction Sheet 408-8493 Application Tooling Loose Piece Contacts—Hand Tool No. 58517-3 (408-4064) Strip Contacts—AMP-O-LECTRIC Model “G” Termination Machine* Applicator No. 567373-3 (Request Catalog 65828) AMP-O-MATIC Stripper-Crimper Machine* Applicator No. 567910-1 or 567827-1 (with CQM) (Request Catalog 65004) AMPOMATOR CLS IIIG Lead Making Machine* (Request Catalog 82659) *Requires applicators. For part numbers, call Technical Support. PAGE 24 .016±.002 [.406±.051] Housing* Technical Documents Application Specifications 114-13036 .440 [11.17] 4 5 6 7 8 9 10 11 12 13 14 15 Dim. A .220 5.59 .320 8.13 .420 10.67 .520 13.21 .620 15.75 .720 18.29 .820 20.83 .920 23.37 1.020 25.91 1.120 28.45 1.220 30.99 1.320 33.53 1.420 36.07 1.520 38.61 Part Numbers No. of Pos. 1375820-2 16 1375820-3 17 1375820-4 18 1375820-5 19 1375820-6 20 1375820-7 21 1375820-8 22 1375820-9 23 1-1375820-0 24 1-1375820-1 25 1-1375820-2 26 1-1375820-3 27 1-1375820-4 28 1-1375820-5 Dim. A 1.620 41.15 1.720 43.69 1.820 46.23 1.920 48.77 2.020 51.31 2.120 53.85 2.220 56.39 2.320 58.93 2.420 61.47 2.520 64.01 2.620 66.55 2.720 69.09 2.820 71.63 Part Numbers .060 .100 [2.54] Typ. 1-1375820-6 1-1375820-7 Typ. 1-1375820-8 1-1375820-9 2-1375820-0 A 2-1375820-1 .510 [12.95] 2-1375820-2 2-1375820-3 2-1375820-4 .260 [6.60] .190 Ref. [4.83] 2-1375820-5 2-1375820-6 2-1375820-7 2-1375820-8 *Housings without polarizing tabs may be manufactured upon request. Minimums may apply. Contact product engineering or product manager for details. MTA, CST-100 II and SL-156 Connectors CST-100 II Shrouded Headers—Straight and Right-Angle Material and Finish Straight Post (.025 [0.64] Square) Housing—UL94V-0 rated, polyester, black Posts—Copper alloy, tin plated, or .000030 [0.00076] gold over nickel Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Headers with .000015 [0.00038] gold plated post are available upon request. Minimums may apply. 3. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. Post No. 1 Post No. 1 A A .313 [7.95] For mateability options, see matrix on pages 5 and 6. .313 [7.95] .410 [10.41] .280 [7.11] The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight posts and with pegs would be: Base number 644893 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-644893-0 All part numbers are the RoHS equivalent version. Example: No. of Pos. 2 14 Lead Free RoHS Prefix/Suffix 3-644893-2 thru 4-644893-4 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: CST-100 II shrouded headers only mate with CST-100 II housings. All the MTA-100 headers except the MTA-100 shrouded headers mate with CST-100 II housings. .025 [0.64] Typ. .140 [3.56] .125 [3.18] .107 [2.72] Ref. .025 [0.64] .100 [2.54] Typ. .125 [3.18] Min. Edge of Board .050/.040 Dia. [1.27/1.02] .140 [3.56] .092 [2.34] Typ. .176 [4.47] Ref. .107 [2.72] Ref. .176 [4.47] Ref. Note: Consult Product Drawing for details on placing headers onto PC boards. Polarized Retention Peg .042 [1.07] .450 [11.43] Max. .124 [3.15] .100 [2.54] Typ. Edge of Board .050/.040 [1.27/1.02] Dia. .081/.075 Dia. [2.06/1.91] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board (Solder Side of Board Shown) .100 [2.54] Typ. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board (Solder Side of Board Shown) Base Part Numbers Straight Posts With Pegs Header Part Nos. Right-Angle Posts Without Pegs Only Without Pegs No. of Posts/ RoHS Equiv. Header Part Nos. No. of Posts/ RoHS Equiv. Standard UL94V-0, Tin Plated 644893 32-44 644892 32-44 Standard UL94V-0, .000030 [0.00076] Gold Plated 644897 32-44 644896 32-44 No. of Header Posts/ Part Nos. RoHS Equiv. 644894 32-44 644898 32-44 Header Length No. of Circuits 2 3 4 PAGE 25 .092 [2.34] Ref. .100 [2.54] .280 [7.11] .036 .520 [0.91] Max. [13.21] For mating half visuals, see page 23. Header Ordering Information Right-Angle (.025 [0.64] Square) Dim. A .284 7.21 .384 9.75 .484 12.29 Prefix/ Suffix No. of Circuits 3- -2 5 3- -3 6 3- -4 7 Dim. A .584 14.83 .684 17.37 .784 19.91 Prefix/ Suffix No. of Circuits 3- -5 8 3- -6 9 3- -7 10 Dim. A .884 22.45 .984 24.99 1.084 27.53 Prefix/ Suffix 3- -8 3- -9 4- -0 MTA, CST-100 II and SL-156 Connectors .156 [3.96] Centerline MTA-156 IDC Connectors and Headers PRODUCT FACTS • Connectors and headers for 2 through 24 positions; wire sizes of 18, 20, 22, 24 and 26 AWG [0.9–0.12 mm2] • Connectors and headers, except shrouded headers, are end-to-end stackable • Posted connectors for 2,3, 4, 6, 9, 12, 15 and 24 positions • Card edge connectors for 3, 6, 9, 12, 15, 18 and 20 through 24 positions • Connectors preloaded with IDC contacts • All contacts are slotted for insulation displacement (IDC) termination technique • Connector styles include both closed end and feedthru, with and without locking ramps and polarizing tabs • Molded ribs on housing do not allow reverse mating • Contacts are lubricated for fretting corrosion protection • Benefits derived from the MTA-156 system include increases quality and ease of handling such as— • • • • • • One-step assembly No wire stripping No contact damage Reduced wiring errors Simpler tooling Simple maintenance and repair • Meets the material requirements of Table 23.1 of UL1410 Standards for Television Receiver and Video Products (wire-to post connectors only) • Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 • Certified by Canadian Standards Association, File No. LR7189 MTA-156 connectors accept discrete and ribbon cable wire sizes ranging from 18– 26 AWG [0.9–0.12 mm2] with maximum insulation outside diameter .095 [2.41] for single wire and .070 [1.78] for mass termination of wires. Tin plated solid, fused stranded or stranded (7, 16, and 19 strands) wire with PVC insulation can be used on 18 AWG [0.8–0.9 mm2] MTA-156 connectors; 7, 10, and 19 stranded wire on 20 AWG [0.5–0.6 mm2] MTA-156 connectors; and 7 and 19 stranded wire on 22–26 AWG [0.4–0.12 mm2] MTA-156 connectors. Only one wire to be terminated into an IDC contact slot. Mass termination of wire provides the lowest applied cost because it drastically reduces the labor content of virtually any cable or harness assembly required. The wire-to-post connector housing material is flame retardant thermoplastic, either UL94V-2 or UL94V-0 rated. A full line of .156 [3.96] centerline headers completes the system. Headers are available with straight or right-angle posts, in flat friction lock and shrouded styles. Headers are available in 2 through 24 positions. Note: Refer to page 52 for approved wire listings. PAGE 26 Performance Data* Voltage Rating—600 vac Current Rating—7 amp max. for MTA-156 Connector Low-Level Resistance— 3.0 mΩ max. initial Dielectric Withstanding Voltage— 2200 vac/1 min. Insulation Resistance— 5000 MΩ min. initial Operating Temperature— -55° C to +105° C *Refer to the Product Specification for additional electrical, mechanical and environmental performance tests and requirements. Technical Documents Product Specification 108-1051 MTA-156 Connectors Application Specifications 114-1020 MTA-156 Connectors, Posted Connectors and Card Edge Connectors 114-1032 MTA-156 Ribbon Cable Assembly MTA, CST-100 II and SL-156 Connectors MTA-156 Connector/Header Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. 640 3 83 640 3 84 640 3 85 640 3 87 640 3 88 640 3 89 640 445 644 611 644 613 644 615 644 617 644 749 644 750 644 751 644 752 644 753 644 754 644 755 647 123 647 125 647 127 647 64 1744 6 017 Headers Matrix for Tin Plated Part Numbers 640426 640427 640428 640429 640430 640431 640432 640433 640434 640435 640472 640473 640474 Connectors 640477 640480 640595 640599 640600 640601 640602 640604 640605 640606 640607 640608 641302 643817 643818 643819 643820 643821 644082 644461 644462 644463 644464 644465 644466 644467 644468 644469 644470 644471 644501 644502 644566 644570 644783 644791 644860 644878 PAGE 27 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y N N N Y Y N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N Y Y Y Y Y Y Y N Y N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y N N N Y Y N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N Y Y Y Y Y Y Y N Y N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y MTA, CST-100 II and SL-156 Connectors MTA-156 Connector/Header Mateability Guide (continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 header and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.00076] Gold Plated Part Numbers Connectors 6412 02 6412 03 6412 04 6412 07 6412 08 6412 09 6412 10 644 631 644 633 644 756 644 759 644 76 0 644 76 1 Headers 641217 641218 641219 641220 Y Y Y Y Y Y Y Y Y Y Y Y N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 641222 641223 641224 641226 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 641227 641228 641229 641230 641235 644460 644662 644663 644718 644720 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N Y N N N N N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Matrix for .000015 [0.00038] Gold Plated Part Numbers PAGE 28 Connectors 6411 13 6411 19 6411 20 6411 21 644 766 3 644 767 644 768 644 769 Headers 641148 641149 641150 641151 Y Y Y Y 641168 641170 641175 Y Y Y Y Y Y Y N Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N N N N 644284 Y Y Y Y Y Y Y N 647478 Y Y Y Y Y Y Y N 647479 Y Y Y Y Y Y Y N MTA, CST-100 II and SL-156 Connectors MTA-156 IDC Connectors—Closed End Material and Finish Closed End with Locking Ramp Housing—UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts—Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel .245 [6.22] A .100 [2.54] .230 [5.84] .355 .325 [9.02][8.26] .050 [1.27] .725 [18.42] Color Coding by Wire Size for UL94V-2 Connectors .097 [2.46] .156 Typ. [3.96] without Polarizing Tabs 26 AWG—Blue 24 AWG—White 22 AWG—Red 20 AWG—Yellow 18 AWG—Orange .100 [2.54] .258 [6.56] All wire sizes in UL94V-0—Black with Polarizing Tabs .050 [1.27] For mateability options, see matrix on pages 27 and 28. Notes: 1. Only connectors with locking ramp and without polarizing tabs mate with posted connectors on page 38. Mating half visuals for Closed End Connectors with Locking Ramp, see pages 38 thru 41, 43, 45, and 46, (42 and 44 Front Bend Headers only). 2. Refer to pages 52-56 for approved wire listing. 3. For strain reliefs and dust covers, see page 9. 4. For keying plugs and panel mount end caps, see page 35. 5. Other circuit sizes are available upon request. Minimums may apply. Closed End without Locking Ramp .245 [6.22] 6. Connector circuits can be molded closed for keying purposes. Minimums may apply. 7. Where no part numbers appear in the chart, parts can be made available upon request. Minimums may apply. 8. To determine connector overall length (dim. A), multiply .156 x the number of circuits. Example: .156 x 10 circuits equals 1.560 inch [39.62 mm]. A .047 [1.19] .355 .325 [9.02][8.26] .180 [4.57] .050 [1.27] .725 [18.42] .156 Typ. [3.96] without Polarizing Tabs .100 [2.54] .258 [6.56] with Polarizing Tabs .050 [1.27] For mateability options, see matrix on pages 27 and 28. Mating half visuals for Closed End Connectors without Locking Ramp, see pages 39 thru 46. PAGE 29 MTA, CST-100 II and SL-156 Connectors MTA-156 IDC Connectors—Closed End (continued) Connector Ordering Information Base Part Numbers The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors. Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position closed end connector with locking ramp and without polarizing tabs for 18 AWG wire would be: Base number 640426 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640426-0 All part numbers bold face are the RoHS equivalent version. Example: No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-640426-2 3 3-640426-3 4 3-640426-4 5 3-640426-5 6 3-640426-6 7 3-640426-7 8 3-640426-8 9 3-640426-9 10 4-640426-0 11 4-640426-1 12 4-640426-2 13 4-640426-3 14 4-640426-4 15 4-640426-5 16 4-640426-6 17 4-640426-7 18 4-640426-8 19 4-640426-9 20 5-640426-0 21 5-640426-1 22 5-640426-2 23 5-640426-3 24 5-640426-4 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 30 Connector Type & Wire Size Closed End with Locking Ramp Without Tabs With Tabs Connector Part Nos. Standard UL94V-2, Tin Plated 18 AWG 640426 0.8–0.9 mm 2 20 AWG 640427 0.5–0.6 mm 2 22 AWG 640428 0.3–0.4 mm 2 24 AWG 640429 0.2 mm 2 26 AWG 640430 0.12–0.15 mm 2 RoHS Equiv. 32–54 32–54 32–54 Connector Part RoHS Nos. Equiv. 643817 643818 643819 32–54 32–54 32–54 Connector Part RoHS Nos. Equiv. 640431 640432 640433 32–54 32–54 32–54 Connector Part RoHS Nos. Equiv. 644461 1 32–44 644462 1 32–44 644463 1 32–44 1 32–44 32–54 643820 32–54 640434 32–54 644464 32–54 643821 32–54 640435 32–54 — — 32–54 640477 32–54 — — — — — Tape Mounted on Reel UL94V-2, Tin Plated 18 AWG 640472 32–54 644878 0.8–0.9 mm 2 20 AWG 640473 32–54 — 0.5–0.6 mm 2 22 AWG 640474 32–54 644783 0.3–0.4 mm 2 24 AWG — — — 0.2 mm 2 26 AWG — — — 0.12–0.15 mm2 — 32–54 32–44 640480 32–54 — — — — — — — 641222 32–54 — — 641223 32–54 — Standard UL94V-2, .000015 [0.00038] Gold Plated 1 18 AWG 32–42 641148 32–54 644284 0.8–0.9 mm 2 20 AWG 641149 32–54 — — 0.5–0.6 mm 2 22 AWG 1 641150 32–54 647478 32–42 0.3–0.4 mm 2 24 AWG 641151 32–54 — — 0.2 mm 2 26 AWG 641152 32–54 — — 0.12–0.15 mm2 Standard UL94V-0, Tin Plated (Black in color) 1 18 AWG 32–42 — 644860 0.8–0.9 mm 2 22 AWG — — — 0.3–0.4 mm 2 644791 — 1 — Standard UL94V-2, .000030 [0.00076] Gold Plated 1 18 AWG 32–42 641217 32–54 644460 0.8–0.9 mm 2 20 AWG 1 32–42 641218 32–54 644663 0.5–0.6 mm 2 22 AWG 1 32–42 641219 32–54 644662 0.3–0.4 mm 2 24 AWG 641220 32–54 — — 0.2 mm 2 26 AWG 641221 32–54 — — 0.12–0.15 mm2 1 Closed End without Locking Ramp Without Tabs With Tabs — — — 1 641224 32–54 644687 641225 32–54 — — 641226 32–54 — — 641153 32–54 — — 641154 32–54 — — 641155 32–54 — — 641156 32–54 — — 641157 32–54 — — 1 644502 32–42 644082 1 32–42 32–42 1 32–42 1 644501 644566 32–44 Other circuit sizes are available upon request. Minimums may apply. Note: Blocked circuit configurations are available upon request. Contact product engineer or product manager fordetails. Minimums may apply. MTA, CST-100 II and SL-156 Connectors MTA-156 IDC Connectors—Feed-Thru Material and Finish Feed-Thru with Locking Ramp Housing—UL94V-2 rated, nylon, see below for color; or UL94V-0 rated, nylon, black Contacts—Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold-plated over nickel .245 [6.22] A .100 [2.54] .385 .325 [9.78] [8.26] .230 [5.84] Color Coding by Wire Size for UL94V-2 Connectors .050 [1.27] .725 [18.42] 26 AWG—Blue 24 AWG—White 22 AWG—Red 20 AWG—Yellow 18 AWG—Orange .097 [2.46] .156 Typ. [3.96] without Polarizing Tabs .100 [2.54] .258 [6.56] All wire sizes in UL94V-0—Black .050 [1.27] with Polarizing Tabs Notes: 1. Only connectors with locking ramp and without polarizing tabs mate with posted connectors on page 38. 2. Refer to pages 52-56 for approved wire listing. 3. For strain reliefs and dust covers, see page 33 and 34. 4. For keying plugs and panel mount end caps, see page 35. For mateability options, see matrix on pages 27 and 28. Mating half visuals for Closed End Connectors with Locking Ramp, see pages 38 thru 41, 43, 45, and 46, (42 and 44 Front Bend Headers only). Feed-Thru without Locking Ramp 5. Other circuit sizes are available upon request. Minimums may apply. .245 [6.22] 6. Connector circuits can be molded closed for keying purposes. Minimums may apply. 7. Where no part numbers appear in the chart, parts can be made available upon request. Minimums may apply. 8. To determine connector overall length (dim. A), multiply .156 x the number of circuits. Example: .156 x 10 circuits equals 1.560 inch [39.62 mm]. A .047 [1.19] .385 .325 [9.78] [8.26] .180 [4.57] .050 [1.27] .725 [18.42] .156 Typ. [3.96] without Polarizing Tabs .100 [2.54] .258 [6.56] .050 [1.27] with Polarizing Tabs For mateability options, see matrix on pages 27 and 28. Mating half visuals for Closed End Connectors without Locking Ramp, see pages 39 thru 46. PAGE 31 MTA, CST-100 II and SL-156 Connectors MTA-156 IDC Connectors—Feed-Thru (continued) Connector Ordering Information Base Part Numbers The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors. Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 10-position feed-thru connector with locking ramp and without polarizing tabs for 18 AWG wire would be: Base number 640599 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640599-0 All part numbers bold face are the RoHS equivalent version. Example: No. of Lead Free Pos. RoHS Prefix/Suffix 2 3-640599-2 3 3-640599-3 4 3-640599-4 5 3-640599-5 6 3-640599-6 7 3-640599-7 8 3-640599 -8 9 3-640599-9 10 4-640599-0 11 4-640599-1 12 4-640599-2 13 4-640599-3 14 4-640599-4 15 4-640599-5 16 4-640599-6 17 4-640599-7 18 4-640599-8 19 4-640599-9 20 5-640599-0 21 5-640599-1 22 5-640599-2 23 5-640599-3 24 5-640599-4 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 32 Connector Type & Wire Size Feed-Thru with Locking Ramp Without Tabs With Tabs Connector Part Nos. Standard UL94V-2, Tin Plated 18 AWG 640599 0.8–0.9 mm 2 20 AWG 640600 0.5–0.6 mm 2 22 AWG 640601 0.3–0.4 mm 2 24 AWG 640602 0.2 mm2 26 AWG 640595 0.12–0.15 mm 2 RoHS Equiv. Connector Part RoHS Nos. Equiv. 644465 1 644466 1 644467 1 32–44 32–54 644468 1 32–44 32–54 — 32–54 32–54 32–54 Tape Mounted on Reel UL94V-2, Tin Plated 18 AWG 641302 32–54 0.8–0.9 mm 2 20 AWG — — 0.5–0.6 mm 2 22 AWG — — 0.3–0.4 mm 2 24 AWG — — 0.2 mm2 26 AWG — — 0.12–0.15 mm 2 Connector Part RoHS Nos. Equiv. 1 32–44 32–54 644470 1 32–44 640606 32–54 644471 1 640607 32–54 — — — 640608 32–54 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 641232 32–54 — — 641233 32–54 — — 641234 32–54 — — — 641235 32–54 — — — 641236 32–54 — — — — — — — 32–54 — — Standard UL94V-2, .000015 [.00038] Gold Plated 1 18 AWG 641168 32–54 647479 0.8–0.9 mm 2 20 AWG — — — 0.5–0.6 mm 2 1 22 AWG 641170 32–54 647496 0.3–0.4 mm 2 24 AWG — — — 0.2 mm2 26 AWG — — — 0.12–0.15 mm 2 1 Connector Part RoHS Nos. Equiv. 644469 Standard UL94V-2, .00003 [.00076] Gold Plated 1 18 AWG — — 644718 0.8–0.9 mm 2 20 AWG — — — 0.5–0.6 mm 2 1 22 AWG — — 644720 0.3–0.4 mm 2 24 AWG — — — 0.2 mm2 26 AWG 641231 32–54 — 0.12–0.15 mm 2 Standard UL94V-0, Tin Plated 18 AWG — 0.8–0.9 mm 2 22 AWG — 0.3–0.4 mm 2 Feed-Thru without Locking Ramp Without Tabs With Tabs 32–44 32–44 32–44 — 32–44 32–42 640604 640605 — 32–54 — 32–42 641175 32–44 — — — — — — — — — — — — — — — 644570 — — — — — — 1 32–42 — Other circuit sizes are available upon request. Minimums may apply. Note: Blocked circuit configurations are available upon request. Contact product engineer or product manager for details. Minimums may apply. MTA, CST-100 II and SL-156 Connectors MTA-156 Connector Accessories Covers Strain Relief Covers Dust Covers Retention Dimple .335 [8.51] Material (RoHS Compliant) Strain Relief Covers—UL94V-2 rated, nylon, white .440 [11.18] Dust Covers—UL94V-0 rated, polyester, white .440 [11.18] .335 [8.51] .127 [3.23] .105 [2.67] .130 [3.30] A A Base Part Numbers Note: This portion of front locking bar may or may not be present Feed-Thru Covers Strain Relief Covers Closed End Strain Relief Dust Covers Covers No. of Cover No. of Cover Part Nos. Circuits Part Nos. Circuits 643067 2–24 640551 2–24 Dust Covers Retention Dimple Material (RoHS Compliant) .470 [11.94] Strain Relief Cover—UL94V-2 rated, nylon, white .475 [12.07] Dust Covers—UL94V-0 rated, polyester, white .325 [8.26] .127 [3.23] .130 [3.3] A A Base Part Numbers Note: This portion of front locking bar may or may not be present Feed-Thru Strain Relief Dust Covers Covers Cover No. of Cover No. of Part Nos. Circuits Part Nos. Circuits 643071 2–24 640643 2–24 Cover Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described cover. Prefixes and suffixes are determined by the number of circuit positions in the cover. For example, the complete part number for a 10-position closed-end strain relief cover would be: Base number 643067 plus prefix-and-suffix 1- — -0 The correct ordering number is 1-643067-0 PAGE 33 Cover Length No. of Circuits 2 3 4 5 6 7 8 9 Dim. A .312 7.92 .468 11.89 .624 15.85 .780 19.81 .936 23.77 1.092 27.74 1.248 31.7 1.404 35.66 Prefix/ Suffix No. of Circuits -2 10 -3 11 -4 12 -5 13 -6 14 -7 15 -8 16 -9 17 Dim. A 1.560 39.62 1.716 43.59 1.872 47.55 2.028 51.51 2.184 55.47 2.340 59.44 2.496 63.4 2.652 67.36 Prefix/ Suffix No. of Circuits 1- -0 18 1- -1 19 1- -2 20 1- -3 21 1- -4 22 1- -5 23 1- -6 24 1- -7 Dim. A 2.808 71.32 2.964 75.29 3.120 79.25 3.276 83.21 3.432 87.17 3.588 91.14 3.744 95.1 Prefix/ Suffix 1- -8 1- -9 2- -0 2- -1 2- -2 2- -3 2- -4 MTA, CST-100 II and SL-156 Connectors MTA-156 Connector Accessories (continued) Replacement IDC Contacts .125 [3.18] Wire Size AWG mm 2 Material and Finish .637 [16.18] Contacts—Phosphor bronze, post tin plated, .000030 [0.00076] or .000015 [0.00038] post gold plated over nickel 18 20 22 24 26 Notes: TE does not recommend terminating an MTA contact more than one time. Use replacement contacts when required for field repairs or wire changes. 0.8–0.9 0.5–0.6 0.3–0.4 0.2 0.12–0.15 Tin Plated 640631-3 640632-3 640633-3 640634-3 640635-3 Part Numbers .000030 [0.00076] Gold Plated 641143-4 641144-4 641145-4 641146-4 641147-4 Crimp Snap-in Contacts Contacts—Phosphor bronze, tin plated Wire Size AWG mm2 26–22 .12–0.3 22–18 0.3–0.9 .580 [14.73] Material and Finish .105 [2.67] .110 [2.79] .165 Max. [4.19] Part Nos. Loose Piece* Strip** 640557-3 640556-3 640559-3 640558-3 **Hand Tool No. 59837-1 (408-6528) **AMP-O-LECTRIC Model “G” Termination Machine (Request Catalog 65828) Note: Requires applicator. For part number, call Technical Support. Special applications for crimp snap-in contacts are: 1. Double wire per contact 2. Coax or shielded wire 3. Mixed wire size in same connector Note: Only one crimp snap-in contact per connector. PAGE 34 .000015 [0.00038] Gold Plated 641143-3 641144-3 641145-3 641146-3 641147-3 10 MTA, CST-100 II and SL-156 Connectors 70% 3 Pantone 30 MTA-156 Connector Accessories (continued) Keying Plugs Material (RoHS Compliant) UL94V-2 rated, nylon, natural color Note: Removal of contact is not necessary when using keying plug. Loose Piece Part No. 640629-1 (Flush) Used with keyed headers On Carrier Strip Part No. 641623-1 (Flush) (10 per strip) .300 [7.62] .066 [1.68] .500 .065 [1.65] .051 [1.30] Flush Ref. .085 [2.16] 2.525 [64.14] Ref. Part No. 640630-1 (Long Nose) Used with staked post .300 [7.62] .375 [9.52] .051 [1.30] .066 [1.68] .300 .065 [1.65] Long Nose Ref. .125 [3.18] .070 Dia. [1.78] Panel Mount End Caps Part No. 641440-1 Part No. 641533-1 (2-position only) Material (RoHS Compliant) UL94V-2 rated, nylon, black Notes: 1. Both left-hand and right-hand end caps are attached by a connecting tab. This tab must be broken off prior to installing on connector. 2. For best results attach panel mount end caps to the MTA-156 (IDC) connectors shown on pages 29 thru 32. While not preferred, panel mount end caps can be attached to MTA-156 (IDC) posted connector on page 38. No. of Dim. Pos. A .736 3 18.69 .892 4 22.66 1.204 6 30.58 1.672 9 42.47 2.140 12 54.36 2.608 15 66.24 4.012 24 101.9 PAGE 35 .564 [14.33] .550 .410 [13.97] [10.41] .440 [11.18] .520 [13.2] .440 [11.18] .520 [13.2] 3- thru 24-Position 641440-1 See Note 1 Two-Position Only 641533-1 .578 [14.7] A .453 [11.5] .010 [.254] Max. R. Typ. at Min. Tolerance Cutout .453 [11.5] Recommended Panel Cutout (Recommended Panel Thickness .062 [1.57] to .067 [1.70] max.) .010 [.254] Max. R. Typ. at Min. Tolerance Cutout MTA, CST-100 II and SL-156 Connectors MTA-156 Posted Connector/Connector Mateability Guide This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. 6414 35 6414 36 6414 37 6414 38 6414 39 6415 22 6415 23 6415 24 6415 25 Posted Connectors Matrix for Tin Plated Part Numbers 640426 640427 640428 640429 640430 640431 640432 640433 640434 640435 640472 640473 640474 Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Y Y Y Y Y N N N N N Y Y Y Connectors 640477 N N N N N N N N N PAGE 36 640480 640595 640599 640600 640601 640602 640604 640605 640606 640607 640608 N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N N Y Y Y Y Y N N N N N 641302 643817 643818 643819 643820 643821 644082 644461 644462 644463 644464 644465 644466 644467 644468 644469 644470 644471 644501 644502 644566 644570 644783 644791 644860 644878 Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N Y N N N N N N N N N N N N N N N N N N N N N N N Y N MTA, CST-100 II and SL-156 Connectors MTA-156 Posted Connector/Connector Mateability Guide (continued) This matrix has been prepared to assist you, our customer, in defining the correct mating halves for the MTA-156 posted connector and connector combination. Where a “Y” is indicated the combination is a valid mating pair. Where an “N” is indicated the combination is not acceptable for mating. Matrix for .000030 [0.00076] Gold Plated Part Numbers Connectors 644 807 644 809 644 81 2 644 81 4 Posted Connectors 641217 641218 641219 641220 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 641222 641223 641224 641226 641227 641228 641229 641230 641235 644460 644662 644663 644718 644720 N N N N Y Y Y Y N N N N N N N N N N Y Y Y Y N N N N N N N N N N Y Y Y Y N N N N N N N N N N Y Y Y Y N N N N N N Matrix for .000015 [0.00038] Gold Plated Part Numbers PAGE 37 Connectors 643 995 647 476 647 481 Posted Connectors 641148 641149 641150 641151 Y Y Y Y 641168 Y Y Y Y Y Y Y Y Y Y Y 641170 Y Y Y 641175 N N N 644284 N N N 647478 N N N 647479 N N N MTA, CST-100 II and SL-156 Connectors MTA-156 IDC Posted Connectors (Wire-to-Wire)—Closed End, Feed-Thru Closed End Material and Finish 3 4 Housing—UL94V-2 rated, nylon, see chart for color Contacts—Copper alloy, post tin or .000030 [.00076] gold plated over nickel Feed-Thru B Dim. 1 2 B Dim. .105 [2.67] ± .010 A Dim. [± 0.25] A Dim. ± .010 [± 0.25] 1.010 [25.65] .156 [3.96] .487 .355 [12.37] [9.02] Ref. .370 [9.4] Base Part Numbers Connector Ordering Information Standard UL 94V-2, Tin Plated 18 AWG 641435 0.8-0.9 mm 2 20 AWG 641436 0.5-0.6 mm 2 22 AWG 641437 0.3-0.4 mm 2 24 AWG 641438 0.2 mm2 26 AWG 641439 0.12-0.15 mm2 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Color Coding by Wire Size for UL94V-2 Connectors 18 AWG—Orange 20 AWG—Yellow 22 AWG—Red 24 AWG—White 26 AWG—Blue Performance Data Voltage Rating—600 vac Current Rating—7 amp max. Low-Level Resistance—7 mΩ max. initial Dielectric Withstanding Voltage— 1500 vac/1 min. Insulation Resistance—5000 MΩ min. initial Operating Temperature—-55° C to +105° C PAGE 38 .156 [3.96] .487 .385 [12.37] [9.78] Ref. .045 [1.14] Sq. Note: 1. Mating half visuals — pages 29 & 32. 2. Strain relief & dust covers — pages 33 & 34. 3. Approved wire listing — page 52. Prefixes and suffixes are determined by the number of circuit positions in the connector. For example, the complete part number for a 12-position closed end connector for 18 AWG wire would be: Base number 641435 plus prefix-and-suffix 4- — -2 The correct ordering number is 4-641435-2 1.010 [25.65] .370 [9.4] .045 [1.14] Sq. The “Base Part Numbers” Chart at right shows the base part number and number of circuits available for the described connectors. .105 [2.67] 1 Closed End Connector Connector Type & Wire Size Part Nos. 1 Feed-Thru Connector RoHS Equiv. Part Nos. RoHS Equiv. 32,33,34,36,39,42,45,54 641522 32,33,34,36,39,42,45,54 32,33,34,36,39,42,45,54 641523 32,33,34,36,39,42,45,54 32,33,34,36,39,42,45,54 641524 32,33,34,36,39,42,45,54 32,33,34,36,39,42,45,54 641525 32,33,34,36,39,42,45,54 32,33,34,36,39,42,45,54 641526 32,33,34,36,39,42,45,54 644812 32,33,34,36,39,42,45,54 —2 — 644814 32,33,34,36,39,42,45,54 Standard UL 94V-2, .000030 [0.00076] Gold Plated 18 AWG 644807 32,33,34,36,39,42,45,54 0.8-0.9 mm 2 20 AWG — —2 0.5-0.6 mm 2 22 AWG 644809 32,33,34,36,39,42,45,54 0.3-0.4 mm 2 24 AWG — —2 0.2 mm 2 26 AWG 2 — — 0.12-0.15 mm2 Standard UL 94V-2, .000015 [0.00038] Gold Plated 18 AWG 647476 32,33,34,36,39,42,45,54 0.8-0.9 mm 2 22 AWG 643995 32,33,34,36,39,42,45,54 0.3-0.4 mm 2 — 2 — — 2 — 647481 32,33,34,36,39,42,45,54 647497 32,33,34,36,39,42,45,54 MTA-156 Posted Connectors (Closed End and Feed-Thru) will Only mate with MTA-156 connectors with locking ramp and without polarizing tabs. They will NOT mate with MTA-156 Quad Connectors. 2 Parts can be made available upon request. Minimums may apply. 1 No. of Circuits 2 3 4 6 Dim. A .468 11.89 .624 15.85 .780 19.81 1.092 27.74 Technical Documents Product Specification 108-1065 MTA-156 Posted Connector Suffix B .316 8.03 .472 11.99 .628 15.95 .940 23.88 Dim. No. of Circuits -2 9 -3 12 -4 15 -6 24 A 1.560 39.62 2.028 51.51 2.496 63.40 3.900 99.06 Replacement IDC Contacts Material and Finish Contacts — Copper alloy, post tin plated over nickel .126 Application Specification 114-1020 MTA-156 Connectors, Posted Connectors .045 and Card Edge [1.14] Sq. Connectors [3.20] .840 [21.34] .1 00 [2.54] B 1.408 35.76 1.876 47.65 2.344 59.54 3.748 95.20 Wire Size AWG mm 2 18 0.8-0.9 20 0.5-0.6 22 0.3-0.4 24 0.2 26 0.12-0.15 Prefix/ Suffix -9 1- -2 1- -5 2- -4 Part Numbers 3-641425-1 3-641426-1 3-641427-1 3-641428-1 3-641429-1 MTA, CST-100 II and SL-156 Connectors MTA-156 Flat Headers—Straight Material and Finish Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] or .000015 [0.00038] gold over nickel .250 [6.35] .125 [3.18] A .156 [3.96] Typ. .078 [1.98] Typ. .045 [1.14] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. Post No. 1 3. .125 [3.18] solder tail lengths are for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36- 3.18] thick printed circuit boards. 4. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. For mateability options, see matrix on pages 27, 28, and 47. .125 [3.18] .140 Min. [3.56] Solder Tail Length (See Chart) Edge of Board For mating half visuals, see pages 29 thru 32, 49 and 51. .156 [3.96] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be: Base number 640383 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-640383-0 The part numbers in bold face are the RoHS equivalent version. Example: No. of Pos. 2 24 Lead Free RoHS Prefix/Suffix 3-640383-2 thru 5-640383-4 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 39 .400 Ref. [10.16] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board PC Board Hole Diameters Square Round Post Post .080/.070 070/.060 [2.03/1.78] [1.78/1.52] Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Square Posts .125 [3.18] .175 [4.45] Solder tail Solder tail Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. Standard UL94V-0, Tin Plated 640383 2–24 644749 2–24 Round Posts .125 [3.18] .175 [4.45] Solder tail Solder tail Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 640384 2–24 644750 2–24 Standard UL94V-0, .000030 [0.00076] Gold Plated 641202 32–54 644756 32–54 641203 32–54 — — Standard UL94V-0, .000015 [0.00038] Gold Plated 641113 32–54 644763 32–54 — — — — MTA, CST-100 II and SL-156 Connectors MTA-156 Flat Headers—Right-Angle Material and Finish Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] or .000015 [0.00038] gold over nickel Notes: .156 [3.96] Typ. .045 [1.14] Sq. .078 [1.98] Typ. Post No. 1 .125 [3.18] 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. 3. .125 [3.18] solder tail lengths are for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36- 3.18] thick printed circuit boards. .250 [6.35] A A .100 [2.54] .125 [3.18] 4. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. For mateability options, see matrix on pages 27, 28, and 47. .390 [9.91] Solder tail Length (See Chart) Edge of Board For mating half visuals, see pages 29 thru 32, 49 and 51. Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be: Base number 641204 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641204-0 The part numbers in bold face are the RoHS equivalent version. Example: No. of Pos. 2 24 Lead Free RoHS Prefix/Suffix 3-641204-2 thru 5-641204-4 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 40 .390 ± .015 [9.91 ± 0.38] X .156 [3.96] .080/.070 [2.03/1.78] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board .1 25 [3.18] X = .140 [3.56] Min., .430 [10.92] Max. when mated with MTA Connector. 16° Retentive Leg Edge of Board X = .140 [3.56] Min. when mated with SL-156 Wire-to-Board Connector. Y .156 Typ. [3.96] Note: Consult Product Drawing for details on placing headers onto PC boards. Ø .063 ± .002 Typ. [1.60±0.05] Recommended Mounting Hole Pattern for .063[1.60] Thk. PC Board for Retentive Leg Header Y = .140 [3.56] Min., .430 [10.92] Max. when mated with MTA Connector. Base Part Numbers Retentive Leg Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647646 2–12 Square Posts .125 [3.18] Solder tail Header RoHS Part Nos. Equiv. .175 [4.45] Solder tail Header RoHS Part Nos. Equiv. 2–24 644751 2–24 Standard UL94V-0, .000030 [0.00076] Gold Plated — — 641204 32–54 — — Standard UL94V-0, .000015 [0.00038] Gold Plated — — — — — — 640385 MTA, CST-100 II and SL-156 Connectors MTA-156 Friction Lock Headers—Straight Material and Finish .180 [4.57] Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] or .000015 [0.00038] gold over nickel Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. .300 [7.62] A .045 [1.14] .156 Typ. [3.96] 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. Post No. 1 3. .125 [3.18] solder tail lengths are for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36- 3.18] thick printed circuit boards. .125 [3.18] .175 Min. [4.45] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts and a .125 [3.18] solder tail length would be: Base number 641208 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641208-0 All part numbers in bold face are the RoHS equivalent version. Example: Y = .068 [1.73] Max. 2-8 position tin plated and 2–24 position gold plated headers. Y = .073 [1.85] 9-24 position tin plated headers. Solder tail Length (See Chart) Edge of Board .068 [1.7] For mating half visuals, use connectors with a locking ramp for polarization/retention purposes, see pages 29 thru 32, 48, 53 and 55. For polarizing purposes only use connectors without a locking ramp. See pages 29 thru 32, 49 and 51. .450 Ref. [11.43] .425 [10.8] 4. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. For mateability options, see matrix on pages 27, 28, and 47. Y .078 Typ. [1.98] .156 [3.96] .400 [10.16] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board PC Board Hole Diameters Square Round Post Post .080/.070 .070/.060 [2.03/1.78] [1.78/1.52] 16° ± 3° Retentive Leg Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Retentive Leg Header RoHS Part Nos. Equiv. Square Posts .125 [3.18] Solder tail Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 1744017 2 640445 2–24 .175 [4.45] Solder tail Header RoHS Part Nos. Equiv. 640388 2–24 644753 2–24 Standard UL94V-0, .000030 [0.00076] Gold Plated — — 641208 32–54 644759 32–54 641209 32–54 644760 32–54 Standard UL94V-0, .000015 [0.00038] Gold Plated — — 641119 32–54 644766 641120 32–54 644767 32–54 644752 2–24 Round Posts .125 [3.18] .175 [4.45] Solder tail Solder tail Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 32–54 Lead Free No. of Standard RoHS Pos. Prefix/Suffix Prefix/Suffix 2 641208-2 3-641208-2 thru 24 2-641208-4 5-641208-4 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 41 MTA, CST-100 II and SL-156 Connectors MTA-156 Friction Lock Headers—Right-Angle Material and Finish .180 [4.57] Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] or .000015 [0.00038] gold over nickel .300 [7.62] Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin on the solder tail. Y = .068 [1.73] Max. 2-8 position tin plated and 2–24 position gold plated headers. Y = .073 [1.85] 9-24 position tin plated headers. A .156 Typ. [3.96] .045 [1.14] Sq. Y 3. .125 [3.18] solder tail lengths are for .062 [1.57] thick printed circuit boards and .175 [4.45] solder tail lengths are for .093-.125 [2.36- 3.18] thick printed circuit boards. .450 [11.43] Post No. 1 .425 [10.8] 4. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts, front bend, and a .125 [3.18] solder tail length would be: Base number 641210 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-641210-0 All part numbers in bold face are the RoHS equivalent version. Example: .157 [3.99] .212 [5.38] Edge of Board Solder tail Length (See Chart) X .156 [3.96] Rear Bend Front Bend .080/.070 [2.03/1.78] X = .325 [8.26] Min., .400 [10.16] X = .500 [12.7] Min., .650 [16.51] Max., when mated with Max., when mated with MTA Connector. MTA Connector. X = .325 [8.26] Min., .345 [8.76] X = .500 [12.7] Min., when mated Max., when mated with with SL-156 Connector. SL-156 Connector. Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. .425 [10.8] .125 [3.18] For mateability options, see matrix on pages 27, 28, and 47. When using Front Bend Headers—for mating half visuals use connectors with a locking ramp for polarization/ retention purposes. When using Rear Bend Headers—for mating half visuals use connectors without a locking ramp. For polarization purposes only see pages 29 thru 32, 49 and 51. Y .078 [1.98] Typ. Base Part Numbers Square Posts Front Bend .125 [3.18] Solder tail Header RoHS Part Nos. Equiv. .175 [4.45] Solder tail Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 640389 2–24 644754 2–24 Standard UL94V-0, .000030 [0.00076] Gold Plated 641210 32–54 644761 32–54 Standard UL94V-0, .000015 [0.00038] Gold Plated 641121 32–54 644768 32–54 Rear Bend .125 [3.18] .175 [4.45] Solder tail Solder tail Header RoHS Header RoHS Part Nos. Equiv. Part Nos. Equiv. 640387 2–24 644755 2–24 641207 32–54 — — — — — — 644769 32–54 Lead Free No. of Standard RoHS Pos. Prefix/Suffix Prefix/Suffix 2 641210-2 3-641210-2 thru 24 2-641210-4 5-641210-4 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 42 MTA, CST-100 II and SL-156 Connectors MTA-156 Polarized Lock Headers—Straight Material and Finish .210 [5.33] Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] gold over nickel 90° Ref. Typ. Polarized Retention Peg A Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. .156 [3.96]Typ. .076 [1.93] 2. Peg holes are not required in PC Boards when headers without pegs are used. .073 [1.85] .045 [1.14] Post No. 1 3. One peg only on a 2 position header, other position sizes have two pegs. .450 [11.43] .125 [3.18] 4. Headers with .00015 [0.00038] gold plated post are available upon request. Minimums may apply. Peg Hole .066/.062 Dia. [1.68/1.57] For mating half visuals, use connectors with a locking ramp for polarization/ retention purposes, see pages 29 thru 32, 53 and 55. .156 [3.96] Base number 644615 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-644615-0 All part numbers in bold face are the RoHS equivalent version. Example: No. of Pos. 2 18 PC Board Hole Diameters Square Round Post Post .069/.065 .054/.050 [1.75/1.65] [1.37/1.27] .078 [1.98] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Header Ordering Information Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with square posts with pegs would be:: .225 Edge of Board [5.72] Min. .167 [4.24] For por polarizing purposes only use connectors without a locking ramp. See pages 29 thru 32, 49 and 51. .425 [10.80] .125 [3.18] Polarized Retention Peg For mateability options, see matrix on pages 27, 28, and 47. .545 [13.84] .100 [2.54] 5. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Retention Tabs 4 Plc. Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Square Posts Without Pegs With Pegs Header Part Nos. RoHS Equiv. Header Part Nos. Standard UL94V-0, Tin Plated 644611 32–35 644615 RoHS Equiv. 32–48 Standard UL94V-0, .000030 [0.00076] Gold Plated 644627 32–48 644631 32–35 Round Posts Without Pegs With Pegs Header Part Nos. RoHS Equiv. Header Part Nos. RoHS Equiv. — — — — — — — — — — — — Lead Free RoHS Prefix/Suffix 3-644615-2 thru 4-644615-8 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 43 MTA, CST-100 II and SL-156 Connectors MTA-156 Polarized Lock Headers—Right-Angle Material and Finish Housing—UL94V-0 rated, polyester, white Posts—Copper alloy, tin plated .000030 [0.00076] gold over nickel 90° Ref. Typ. Polarized Retention Peg Notes: A 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Peg holes are not required in PC Boards when headers without pegs are used. 3. One peg only on a 2 position header, other position sizes have two pegs. .156 Typ. [3.96] .076 [1.93] Typ. .100 [2.54] Post No. 1 .450 [11.43] .125 [3.18] 5. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with front bend and with pegs would be: Base number 644617 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-644617-0 All part numbers in bold face are the RoHS equivalent version. Example: No. of Pos. 2 18 .545 [13.84] .200 [5.08] Typ. .205 [5.21] Typ. For mateability options, see matrix on pages 27, 28, and 47. For polarizing purposes only use connectors without a locking ramp. See pages 29 thru 32, 49 and 51. .073 [1.85] Typ. .210 [5.33] Typ. Ref. .045 Sq. [1.14] 4. Headers with .00015 [0.00038] gold plated post are available upon request. Minimums may apply. For mating half visuals, use connectors with a locking ramp for polarization/ retention purposes, see pages 29 thru 32, 53 and 55. Retention Tabs 4 Plc. .125 [3.18] .425 [10.80] Front Bend Front Bend Reg. Hole .066/.062 Dia. [1.68/1.57] x .125 [3.18] Rear BendBend Rear X = .350 [8.89] Min., .825 [20.96] X = .500 [12.7] Min., .700 [17.78] Max., when mated with Max., when mated with Edge of Board MTA Connector. MTA Connector. X = .350 [8.89] Min. when mated X = .500 [12.7] Min., when with SL-156 Connector. mated with SL-156 .069/.065 Connector. [1.75/1.65] .239 [6.07] .078 [1.98] .156 [3.96] Recommended Mounting Hole Pattern for .062 [1.57] Thk. PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Square Posts Front Bend Without Pegs Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 644613 32–48 With Pegs Header RoHS Part Nos. Equiv. 644617 Standard UL94V-0, .000030 [0.00076] Gold Plated — — 644633 Rear Bend Without Pegs Header RoHS Part Nos. Equiv. 32–48 — — 32–48 — — Lead Free RoHS Prefix/Suffix 3-644617-2 thru 4-644617-8 See page 8 for an explanation of RoHS lead free equivalents. Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 44 MTA, CST-100 II and SL-156 Connectors MTA-156 Friction Lock High Temperature Headers—Straight For use with Infrared Reflow Process Material and Finish Housing—UL94V-0 rated, nylon, black Posts—Copper alloy, tin plated .000015 [0.00038] gold over nickel Temperature—Maximum Temperature Rating: 280°C A Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin-lead on the solder tail. 3. Headers with straight and right-angle square posts are available upon request. Minimums may apply. .156 Typ. [3.96] .076 ± .003 [1.93 ± 0.08] 2 Plcs. Ø .045 ± .001 Ref. [1.14 ± 0.03] Mating End Post No. 1 .700 ± .010 77 ± 25 .125 [3.18] + .005 .073 – .010 15 + 1 – 25 .210 [5.33] .450 [11.43] 1 .545 ± .010 ± 25 4. To determine header overall length (Dim. A), multiply .156 x the number of posts. Example: .156 x 10 posts equals 1.560 inches [39.62 mm]. Solder tail For mateability options, see matrix on pages 27, 28, and 47. 1 .425 [10.80] For mating half visuals, use only connectors with a locking ramp for polarization/ retention purposes, see pages 29 thru 32, 53 and 55. .156 [3.96]Typ. .120 [3.05]Typ. For polarizing purposes only use connectors without a locking ramp. See pages 29 thru 32, 49 and 51. Position No. 1 .650 ± .010 [16.51 ± 0.25] Solder Paste Area .057 ± .003 [1.45 ± 0.08] Pretinned Plated Thru Hole Typ. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with round tin plated posts:: Base number 647648 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647648-0 All part numbers in bold face are the RoHS equivalent version. Example: No. of Pos. 2 18 Lead Free RoHS Prefix/Suffix 3-647648-2 thru 4-647648-2 See page 8 for an explanation of RoHS lead free equivalents. .008 [0.20] Min. Thick Solder Paste in Area Shown .120 Typ. [3.05] Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. .335 [8.51] .125 ± .010 ± 25 .100 [2.54] Pretinned Land (Both Sides) Typ. .070 Typ. [1.78] Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board Note: Consult Product Drawing for details on placing headers onto PC boards. Base Part Numbers Round Post Header Part Nos. Standard UL94V-0, Tin Plated 647648 RoHS Equiv. 32–42 Standard UL94V-0, .000015 [0.00038] Gold Plated 647649 32–42 Note: All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. PAGE 45 MTA, CST-100 II and SL-156 Connectors MTA-156 Shrouded Headers—Straight and Right-Angle Material and Finish Straight Post (.045 [1.14] Square or Round) Housing—UL94V-0 rated, polyester, black Posts—Copper alloy, tin plated; or .000030 [0.00076] or .000015 [0.00038] gold over nickel Notes: 1. Post(s) can be omitted for keying purposes. Specify the desired post(s) to be omitted using the figure to identify Post No. 1. 2. Gold headers are duplex plated, gold on mating end of post and tin-lead on the solder tail. 3. Peg holes are not required in PC boards when headers without pegs are used. 4. One peg only on a 2 position header, other position sizes have two pegs. 5. Right-angle front and rear bend headers with retention pegs can be made available upon request. Minimums may apply. For mateability options, see matrix on pages 27, 28, and 47. For mating half visuals, see pages 29 thru 32. Header Ordering Information The “Base Part Numbers” Chart at right shows the base part number and number of posts available for the described headers. Prefixes and suffixes are determined by the number of post positions in the header. For example, the complete part number for a 10-position header with straight, square posts and with pegs would be: Base number 647127 plus prefix-and-suffix 4- — -0 The correct ordering number is 4-647127-0 No. of Dim. RoHS Pos. A Prefix/Suffix 2 3 4 5 6 7 8 9 10 11 12 .406 10.31 .562 14.27 .718 18.24 .874 22.20 1.030 26.16 1.186 30.12 1.342 34.09 1.498 38.05 1.654 42.01 1.810 45.97 1.966 49.94 .455 [11.56] .300 [7.62] Post No. 1 .205 ± .002 .156 Typ. Post [5.21 ± 0.05] [3.96] No. 1 .210 [5.33] .525 [13.34] .100 .167 [2.54] [4.24] .125 ± .010 [3.18 ± 0.25] .300 [7.62] Ref. .125 [3.18] .455 [11.56] .210 [5.33] .525 [13.34] Ref. .205 [5.21] PC Board Hole Diameters Square Post .069/.065 [1.75/1.65] Round Post .054/.050 [1.37/1.27] .156 Typ. Post [3.96] No. 1 .125 [3.18] Rear Bend Note: Consult Product Drawing for details on placing headers onto PC boards. .069/.065 Dia. [1.75/1.65] .239 [6.07] .167 [4.24] .066/062 [1.68/1.58] Dia. .245 Min. [6.22] Edge of Board .156 [3.96] .066/062 [1.68/1.58] Dia. .078 [1.98] .350/.700 [8.89/17.78] .078 [1.98] Edge of Board .156 [3.96] Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board Using a Straight Post Header Recommended Mounting Hole Pattern for .062 [1.57] Thick PC Board Using a Right-Angle Header Base Part Numbers Straight Square Posts Without Pegs With Pegs Header Part Nos. RoHS Equiv. Header Part Nos. Standard UL94V-0, Tin Plated 647123 22–32 647127 RoHS Equiv. Straight Round Posts Without Pegs With Pegs Header Part Nos. RoHS Equiv. Header Part Nos. RoHS Equiv. — — — — 2--2 — — — — 2--3 Standard UL94V-0, .000015 [0.00038] Gold Plated — — — — — — — — 22–32 2--4 2--5 2--6 2--7 2--8 2--9 3--0 3--1 3--2 .210 [5.33] Front Bend .550 [13.97] .045 [1.14] .125 [3.18] .156 [3.96] .455 [11.56] .525 [13.34] Ref. Polarized Retention Peg A .045 [1.14] .300 [7.62] Ref. .045 [1.14] Standard UL94V-0, .000030 [0.00076] Gold Plated — — — — All RoHS equivalent part numbers may not be available upon catalog release. If the number you need is not available, please contact Product Engineering to expedite your request. PAGE 46 Right-Angle (.045 [1.14] Square) Square Posts Right-Angle Posts, Front Bend Without Pegs Header RoHS Part Nos. Equiv. Standard UL94V-0, Tin Plated 647125 22–32 Standard UL94V-0, .000030 [0.00076] Gold Plated — — Right-Angle Posts, Rear Bend Without Pegs Header RoHS Part Nos. Equiv. — — — — Standard UL94V-0, .000015 [0.00038] Gold Plated — — — — Note: Select load headers (omitted pin headers) are available upon request. Please contact product engineer or product manager for details. MTA, CST-100 II and SL-156 Connectors .156 [3.96] Centerline SL-156 Crimp Contacts and Housings PRODUCT FACTS • Rugged wire-to-board interconnection to mate with .045 square or round post headers or staked posts on .156 centers • Standard Connectors accept wire range of 18–24 AWG [0.9–0.2 mm] and LID Connectors accept wire range of 18–24 AWG [0.9–0.2 mm] and a limited 16 AWG [1.29–1.42 mm] (2550–2800 CMA) • Two-piece interconnection system (connector/header) • Housing made of flame retardant nylon • Available in 1- through 24-position connector configurations • Connectors are end-to-end stackable • Wire-to-board system offers polarization with friction lock for positive mating • Meets the material requirements of Table 23.1 of UL1410 Standard for High-Voltage Television Receivers and Video Productions • Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 • Certified by Canadian Standards Association, File No. LR7189 Performance Data* The AMP SL-156 connectors shown on the following pages are designed to mate with .045 [1.14] square or round post headers or staked posts on .156 [3.96] centers. Voltage Rating—250 vac Current Rating—10 amp max. at 250 vac Low-Level Resistance—3.0 mΩ max. initial Dielectric Withstanding Voltage— 2000 vac/1 min. The wire-to-board connector is a twopiece connector system with the wire crimped to the contact, then inserted into the housing. This product mates with the MTA-156 flat, polarized and friction lock header, or staked posts (not MTA-156 shrouded headers). Insulation Resistance—1000 MΩ min. initial Operating Temperature—-55° C to +105° C The Large Insulation Diameter (LID) Contacts and Housings are for use in applications where wire insulation is up to .112 [2.84] in diameter. These matrixes represent only the housing and header combinations. You also need to consider the plating on the contacts and headers. Gold contacts with gold headers and tin contacts with tin headers. 640 383 640 384 640 385 640 387 640 388 640 389 640 445 644 611 644 612 644 613 644 614 644 615 644 616 644 617 644 749 644 750 644 751 644 752 644 753 644 754 644 755 647 227 647 228 647 229 647 230 647 260 647 262 Matrix for Tin Plated Part Numbers Housings Headers Standard LID 640250 647401 Y N Y 640251 647400 Y Y Y 770849 647402 Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y N Y Y Y 202 641 203 641 204 641 207 641 208 641 209 641 210 644 627 644 628 644 629 644 630 644 631 644 632 644 633 644 756 644 757 644 758 644 759 644 760 644 761 644 762 641 Matrix for .000030 [0.00076] Gold Plated Part Numbers Housings Headers Standard LID 640250 647401 Y Y Y N Y Y Y Y Y Y N Y Y Y Y Y 640251 647400 Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y 770849 647402 Y Y Y N Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y N PAGE 47 641 113 641 114 641 115 641 118 641 119 641 120 641 121 644 322 644 763 644 764 644 765 644 766 644 767 644 768 644 769 647 261 Matrix for .000015 [0.00038] Gold Plated Part Numbers Housings Headers Standard LID 640250 647401 Y Y Y N Y Y Y Y Y 640251 647400 Y Y Y Y Y Y Y Y Y 770849 647402 Y Y Y N Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y N Y N Y Y Y Y Y N Y Y MTA, CST-100 II and SL-156 Connectors SL-156 Crimp Contacts and Keying Plugs Contacts .180 [4.57] .115 [2.92] Material and Finish .012 [0.3] bright tin plated brass or phosphor bronze; .012 [0.3] pre-tin brass; or .012 [0.3] brass or phosphor bronze with .000030 [0.00076] gold over nickel (see chart) • All tin-plated contacts are post lubricated to resist fretting corrosion • Maximum insulation diameter is .105 [2.67] • Wire range is 18-30 AWG [0.9-0.06 mm2] .131 ± .004 [3.33 ± 0.10] .121/.115 [3.07/2.92] A High Force (6.5 Amp Max. Current Rating) B Low Force (6.5 Amp Max. Current Rating) .230 [5.84] .145/.140 [3.68/3.56] C Hooded (Dual Wipe) (10 Amp. Max. Current Rating) Application Note Part No. 640252 has a higher mating and unmating force than Part No. 350980 and is recommended to be used only in housings with 1 through 12 positions. Wire Size AWG mm 2 24–30 0.2-0.06 Contact A C 640252-1 640252-2 3-640252-1 350980-1 350980-2 350980-3 3-350980-1 770476-1 770476-2 3-770476-1 Extraction Tool Part No. 90471-1 Loose Piece Contacts — PRO-CRIMPER II Hand Tool Part No. 58614-1 (408-4228) [For field service use only] For CERTI-CRIMP hand tool, contact Technical Support. Keying Plugs 640706-1 640706-2 3-640706-1 640707-1 — 770258-1 3-640707-1 770522-1 770522-2 3-770522-1 .300 [7.62] Strip Contacts — AMP-O-LECTRIC Model “G” Termination Machine* Applicator 680211-3 (Request Catalog 65828) AMP-O-LECTRIC Model “K” Termination Machine* Applicator 466468-2 AMP-O-MATIC Stripper-Crimper Machine* SCA 466947-1 or 567828-1 (with CQM) (Request Catalog 65004) AMPOMATOR CLS IV+ Lead Making Machine* Applicator 466468-1 (Request Catalog 82659) *Requires applicators. For part numbers, call Technical Support. .225 [5.72] .300 [7.62] UL94V-2 rated, nylon, natural color Keying Plug Part No. 640254-1 PAGE 48 — Application Tooling For housings, see pages 49 and 50. Material (RoHS Compliant) Part Numbers Loose Piece 641550-1 brass, bright tin plated brass, pre-tin plated brass, RoHS Compliant brass, bright tin plated brass, pre-tin plated brass, gold plated brass, RoHS Compliant phosphor bronze, bright tin plated phosphor bronze, gold plated phosphor bronze, RoHS Compliant B Part No. 350980 can be used in any size housing but is recommended to be used in housings with 13 through 24 positions. Part No. 770476 is recommended for use in any size housing. Its mating force is similar to Part No. 350980 while unmating force is similar to 640252. Strip brass, pre-tin plated A 18–24 0.9-0.2 Material and Finish Keying Pin Part No. 640255-1 MTA, CST-100 II and SL-156 Connectors SL-156 Housings—Wire-to-Board .660 [16.76] Housings A .156 [3.96] Typ. .100 [2.54] .019 [0.48] Material (RoHS Compliant) UL94V-0 rated, nylon, white .076 [1.93] Typ. .097 [2.46] Notes: 1. Accepts either .045 [1.14] square or round posts. Housings mate with flat and friction lock headers, or staked posts on .156 [3.96] centers. .250 [6.35] 2. Housings without ramp, with polarizing tab, available upon request. Minimums may apply. 1 2 23 24 .037 Ref. [0.93] (A) With Locking Ramp/With Polarizing Tabs 3. Recommend contact: Part No. 640252 for 1 thru 12 positions; Part No. 350980 for 13 thru 24 positions; Part No. 770476 for 1 thru 24 positions. .660 [16.76] For contacts, see page 48. For mateability options, see matrix on page 47. For mating half visuals, for connectors with locking ramp, see pages 39, 36, 41, 43 and 45, (41 and 44 Front Bend Headers only.) For mating half visuals, for connectors without locking ramp, see pages 35 thru 45. A .100 [2.54] .156 [3.96] Typ. .250 [6.35] 1 .076 [1.93] Typ. 2 23 .097 [2.46] .037 Ref. [0.93] 24 (B) With Locking Ramp/Without Polarizing Tabs A .660 [16.76] .076 [1.93] Typ. .156 [3.96] Typ. .250 [6.35] 1 2 23 24 .060 [1.52] (C) Without Locking Ramp/Without Polarizing Tabs Note: Dim. A = 0.156 No. of Positions* 2–24 1–24 Housing A B C (No. of Positions – 1) 0.152 Description With Locking Ramp and Polarizing Tabs With Locking Ramp and without Polarizing Tabs Without Locking Ramp or Polarizing Tabs Part Numbers* 770849 640250 640251 *Base Part Number Prefixes and Suffixes indicate number of contact positions, e.g. 2 Position = 0-xxxxxx-2 and 12 Position = 1-xxxxxx-2. Note: Housings not for use with LID Contacts. Shown on page 51. PAGE 49 MTA, CST-100 II and SL-156 Connectors SL-156 Housings With Through Board Latch Housings Material (RoHS Compliant) UL94V-0 rated, nylon, white. .156 [3.96] Typ. .078 [1.98]Typ. .125 [3.18] .063 ± .003 [1.60 ± .008] 1 2 3 4 7 8 9 10 .075 [1.91] .250 [6.35] .050 ± .007 [1.27 ± .018] .063 ± .003 [1.60 ± .008] .660 [16.76] A Mates with .045 square or round staked posts only. For contacts, see page 48. 10 9 8 7 4 3 2 1 B .105 [2.67] .052 ± .002 [1.32 ± .005] .105 [2.67] Latch Cutout +.005 .163 -.000 [4.14 +.013 -.000 R. .015 Max. [0.38] 4 Plc. .078 [1.98] PC Board Posts .156 [3.96] Recommended PC Board Cutout for .062 [1.57] Thick PC Board No. of Pos. 2 3 4 5 6 7 8 9 10 Dimensions A .312 7.92 .468 11.89 .624 15.85 .780 19.81 .936 23.77 1.092 27.74 1.248 31.70 1.404 35.66 1.560 39.62 Note: Not for use with LID Contacts. PAGE 50 B Latch Location Centered Between Pos. Part Number — 1 and 2 1- 770894-2 — 1 and 2 1- 770894-3 — 2 and 3 1- 770894-4 — 2 and 3 1- 770894-5 — 3 and 4 1- 770894-6 — 3 and 4 1- 770894-7 — 4 and 5 1- 770894-8 1 and 2 & 8 and 9 1- 770894-9 1 and 2 & 9 and 10 1-770894-0 1.092 27.74 1.248 31.70 MTA, CST-100 II and SL-156 Connectors SL-156 Housings and Contacts for Large Insulation Diameter (LID) Wire Housings .156 Typ. [3.96] .095 Typ. [2.41] Material (RoHS Compliant) UL94V-0 rated, nylon, white .660 [16.76] .054 [1.37] Typ. .100 [2.54] Notes: 1. Accepts Standard and LID contacts. 2. Larger opening in housings eases contact insertion when using wires that have large insulation diameters (.100-.112 [2.54-2.84]). .054 [1.37] A 3. Housings are not End-to-End stackable. For mateability options, see matrix on page 47. For mating half visuals, for connectors with locking ramp, see pages 39, 40, 41, 43 and 49, (42 and 44 Front Bend Headers only.) For mating half visuals, for connectors without locking ramp, see pages 39 thru 45. Contacts Note: Dim. A = 0.156 (No. of Positions – 1) No. of Positions* 2–24 .112 [2.84] .108[2.74] .524 [13.30] .143 Product Specifications 108-1049-1 and 108-1049-2 Application Specification 114-1021 AMP-O-LECTRIC Model “G” Termination Machine* Applicator 1385048-3 [18-24 AWG] Applicator 1385219-3 [16 AWG] AMP-O-LECTRIC Model “K” Termination Machine* Applicator 1385048-2 [18-24 AWG] Applicator 1385219-2 [16 AWG] *For additional part numbers and information contact Technical Support. PAGE 51 647402 .160 [4.06] • Wire range is 18-24 AWG [0.9-0.2 mm2] and a limited 16 AWG [1.29-1.42 mm2] (2550-2800 CMA) Strip Contacts — 647400 647401 (shown above) *Base Part Number Prefixes and Suffixes indicate number of contact positions, e.g. 2 Position = 0-xxxxxx-2 and 12 Position = 1-xxxxxx-2. • Maximum insulation diameter is .112 [2.85] PRO-CRIMPER II Hand Tool Part No. 91368-1 [18-24 AWG] Part No. 91369-1 [16 AWG] (For field service use only.) For CERTI-CRIMP hand tool, contact Technical Support. Part Numbers* Housings with Larger Openings for Oversize Wire Without Locking Ramp or Polarizing Tabs With Locking Ramp and without Polarizing Tabs With Locking Ramp and Polarizing Tabs 1-24 • All tin-plated contacts are post lubricated to resist fretting corrosion Loose Piece Contacts — 0.19 Description Material and Finish .012 [0.3] bright tin plated phosphor bronze; .012 [0.3] phosphor bronze with .000030 [0.00076] gold over nickel (see chart) Application Tooling Extraction Tool Part No. 90471-1 .250 [6.35] .0365 [.927] Ref. Hooded (Dual Wipe) (10 Amp Max. Current Rating) Wire Size Material 18-24 AWG Phosphor Bronze 16 AWG (2550-2800 CMA only) Phosphor Bronze Plating Tin Gold RoHS Compliant Tin Gold RoHS Compliant Part Numbers For LID* Wire Strip Loose Piece 647406-1 647409-1 647406-2 647409-2 3-647406-1 3-647409-1 647466-1 647485-1 647466-2 647485-2 3-647466-1 3-647485-1 *Large Insulation Diameter (.100-.112 [2.54-2.84]) Notes: 1. For information on application tooling, call Technical Support. 2. Can not be used with Standard SL-156 Housings, must be used with LID Housings only. MTA, CST-100 II and SL-156 Connectors MTA Wire Selection Proper wire selection is critical to the success of a wire-to board application. The chart identifies wires that have been evaluated and approved by the product engineering section. If you plan to use a wire not on the approved list, please submit a sample 12” length of wire to TE for evaluation. AWG Metric Equivalents 18 — 0.8–0.9 mm2 20 — 0.5–0.6 mm2 22 — 0.3–0.4 mm2 24 — 0.2 mm2 26 — 0.12–0.15 mm2 28 — 0.08–0.09 mm2 Product Specifications 108-1050 — MTA-100 Connectors 108-1050-1 — MTA-100 Posted Connectors 108-1051 — MTA-156 Connectors 108-1219 — MTA-156 Quad Connector System 108-1065 — MTA-156 Posted Connectors 108-1058 — MTA-156 Card Edge Connectors Application Specifications 114-1019 — MTA-100 Connectors 114-1020 — MTA-156 Connectors 114-1031 — MTA-100 Ribbon Cable Connector Assembly 114-1032 — MTA-156 Ribbon Cable Connector Assembly 114-1048 — MTA-156 Quad Connector MTA Connectors Approved Wire Listing MTA-100 Connectors UL 1007 PVC Insulation UL 1061 Semi-Rigid PVC Insulation UL 1095 Semi-Rigid PVC Insulation UL 1371 TEFLON Insulation — TFE UL 1429 Irradiated PVC — X.L.P.V.C. UL 2464 PVC UL 3265 Irradiated Polyethylene — X.L.P.E. UL 3266 Irradiated Polyethylene — X.L.P.E. MIL-W-16878, Type B-PVC Insulation UL 1213 TEFLON Insulation—T.F.E. MTA-156 Connectors UL 1007 PVC Insulation UL 1061 Semi-Rigid PVC Insulation UL 1180 TEFLON Insulation — T.F.E. UL 1213 TEFLON Insulation — T.F.E. UL 1316 PVC/Nylon Wall UL 1429 Irradiated PVC — X.L.P.V.C. UL 1430 Irradiated PVC — X.L.P.V.C. UL 1569 PVC UL 3265 Irradiated Polyethylene — X.L.P.E. UL 3266 Irradiated Polyethylene — X.L.P.E. Wall .015″ [0.381] .009″ [0.229] .012″ [0.305] .006″ [0.152] .010″ [0.254] .013″ [0.330] .010″ [0.254] .015″ [0.381] .010″ [0.254] .010″ [0.254] Approved Wire AWG 22, 24, 26, 28 22, 24, 26, 28 24 22, 26 22, 24, 26, 28 24,26 22, 24 22, 24 22 22 .015″ [0.381] .009″ [0.229] .015″ [0.381] 010″ [0.254] .015″ [0.381] .010″ [0.254] .015″ [0.381] .015″ [0.381] .010″ [0.254] .015″ [0.381] 18, 20, 22, 24 18, 20, 22, 24 22 18, 22, 24 18, 22 18, 20, 22, 24 18, 20, 22, 24 18 22 18, 20, 22, 24 Note: When selecting approved wire styles noted on this list, the MTA Application Specifications guidelines must be followed. Also, due to wire variations in insulation wall thickness, hardness and wire stranding we would recommend evaluating the wire selected before final application approval. TEFLON is a trademark of E.I. DuPont de Nemours and Company. MTA-100 Ribbon Cable Preparation .036-.046 Standard (.046-.052 Allowable for 26-28 AWG Wire Only) Dead-End Notch .280-.450† [7.112-11.43] MTA-156 Ribbon Cable Preparation .036-.046 Standard (.046-.052 Allowable for .062-.080 26-28 AWG Wire Only) [1.57-2.03] Feed-Thru Notch .400-.800† [10.16-20.32] .100 [2.54] (Typ.) .062-.080 [1.57-2.03] Flush-Mount Notch .400-.600† [10.16-15.24] Insulation .050 [1.27] Dia. (Max.) For Mass Terminating .064 [1.63] Typ. (Max.) After Notching .500-1.000† [12.70-25.40] Insulation (Typ.) Conductor Web .156 [3.96] Feed-Thru Notch Conductor Ribbon Cable End View .070 [1.78] Dia. (Max.) For Mass Terminating Web .094 [2.39] Typ. (Max.) After Notching † The dimensions shown represent the recommended minimum and maximum for notches; the actual dimension will depend on your application requirements. Notes: 1. Cable shall be notched, as indicated in the individual ribbon cable connector assembly drawing, according to the requirements specified in these figures. Conductor shall not be exposed after notching, nor shall individual wire stands be cut or nicked. 2. U.L. Style #2651 ribbon cable is approved for use with MTA-100 and MTA-156 connectors per Application Specification 114-1031 and 114-1032. Ribbon Cable –A– Notes: 1. For MTA Cable Assemblies Contact US Engineering Cable Assembly Group. 2. For IDC Cable, see pages 60 thru 63. PAGE 52 .010 A Per Inch of Cable Width Cable Edge-to-End Alignment (Ends of the cable shall be prepared as indicated in this figure) MTA, CST-100 II and SL-156 Connectors IDC Ribbon Cable PRODUCT FACTS • Compatible with a variety of Insulation Displacement Connectors • Available on .025 [0.63], .0394 [1.00], .050 [1.27], .100 [2.54] and .156 [3.96] centerline • Color code edge mark on conductor #1 • Gray flame retardant flexible PVC insulation • Insulation rated for temperature of -20°C to +105°C • Recognized under the Component Program of Underwriters Laboratories Inc., File No. E53793 TE has an expanding array of MADISON CABLE planar PVC insulated product designed for compatibility with a variety of Insulation Displacement Connectors. AMP IDC terminations offer a quick, reliable, cost-effective cabling system which can be automated. The .100 [2.54] centerline cable is available in 28 to 22 AWG, either as tinned or as overcoated tinned wire, in 2 to 28 conductors. .050 [1.27] Centerline, IDC Ribbon Cable Product Specifications Sizes Voltage Rating—30 vac 26 AWG, 7/34 Tinned copper, PVC insulation (9–64 conductors), 500 ft. reels (Base AMP Part Number 57034) Component Recognized by UL to US and Canadian Standards—AWM Style 2651 28 AWG, 7/36 Tinned copper, PVC insulation (9–64 conductors), 100 ft. reels (Base AMP Part Number 57040) and 500 ft. reels (Base AMP Part Number 971111) 30 AWG, Other conductor counts available on request. For ordering information, call Toll-Free: 1-877-623-4766 or visit: www.madisoncable.com/fsproducts.htm PAGE 53 The .156 [3.96] centerline is available in 22 AWG and 18 AWG, either as tinned or overcoated tinned, in 2 to 24 conductors. IDC Ribbon Cable is produced to tighter standards than usually required for high yield insulation displacement terminations. The extra precision offers uncomplicated operation in fully automatic stripping, notching and termination equipment. MTA, CST-100 II and SL-156 Connectors .100 [2.54] Centerline, IDC Ribbon Cable, PVC Insulation Product Specifications B Housing — 300 Volts UL Recognized — AWM Style 2651 CSA —Available on request A .050 [1.27] Typ. C .010 [0.25] .100 [2.54] Typ. Edge Mark No. of Conductors A Dimensions B C Part Number No. of Conductors A Insulation — Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating — -20°C to +105°C Flammability — UL: VW1 Dimensions B C Part Number 28 AWG 7/32 Tinned Copper 2 0.100 [2.54] 0.200 [5.08] 5 0.400 [10.16] 0.500 [12.70] 10 0.900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 0.044 [1.12] 0.044 [1.12] 0.044 [1.12] 0.044 [1.12] 0.044 [1.12] 0.044 [1.12] 0.044 [1.12] 02WFY00006P 05WFY00006P 10WFY00006P 15WFY00006P 20WFY00006P 25WFY00006P 28WFY00006P 24 AWG 7/32 Overcoated Tinned Copper 2 0.100 [2.54] 0.200 [5.08] 0.044 [1.12] 5 0.400 [10.16] 0.500 [12.70] 0.044 [1.12] 10 0.900 [22.86] 1.000 [25.40] 0.044 [1.12] 15 1.400 [35.56] 1.500 [38.10] 0.044 [1.12] 20 1.900 [48.26] 2.000 [50.80] 0.044 [1.12] 25 2.400 [60.96] 2.500 [63.50] 0.044 [1.12] 28 2.700 [68.58] 2.800 [71.12] 0.044 [1.12] 02WFY00007P 05WFY00007P 10WFY00007P 15WFY00007P 20WFY00007P 25WFY00007P 28WFY00007P 26 AWG 7/34 Tinned Copper 2 0.100 [2.54] 0.200 [6.08] 5 0.400 [10.16] 0.500 [12.70] 10 0.900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 0.039 [.99] 0.039 [.99] 0.039 [.99] 0.039 [.99] 0.039 [.99] 0.039 [.99] 0.039 [.99] 02WEY00008P 05WEY00004P 10WEY00012P 15WEY00002P 20WEY00008P 25WEY00008P 28WEY00008P 22 AWG 7/30 Tinned Copper 2 0.100 [2.54] 0.200 [5.08] 5 0.400 [10.16] 0.500 [12.70] 10 0.900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 02WGY00001P 05WGY00006P 10WGY00002P 15WGY00006P 20WGY00006P 25WGY00006P 28WGY00006P 26 AWG 7/34 Overcoated Tinned Copper 2 0.100 [2.54] 0.200 [5.08] 0.039 [.99] 5 0.400 [10.16] 0.500 [12.70] 0.039 [.99] 10 0.900 [22.86] 1.000 [25.40] 0.039 [.99] 15 1.400 [35.56] 1.500 [38.10] 0.039 [.99] 20 1.900 [48.26 ]2.000 [50.80] 0.039 [.99] 25 2.400 [60.96] 2.500 [63.50] 0.039 [.99] 28 2.700 [68.58] 2.800 [71.12] 0.03 [.99] 02WEY00007P 05WEY00007P 10WEY00007P 15WEY00007P 20WEY00007P 25WEY00007P 28WEY00007P Other Conductor Counts Available on Request. Contact MADISON CABLE (1-877-MADISON), a division of TE Connectivity, for engineering questions or for order placement of this cable. PAGE 54 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] MTA, CST-100 II and SL-156 Connectors .156 [3.96] Centerline, Flat Ribbon Cable, PVC Insulation Product Specifications B Housing — 300 Volts UL Recognized — AWM Style 2651 CSA —Available on request A .078 [1.98] Typ. C .010 [0.25] Edge Mark No. of Conductors A .156 [3.96] Typ. Dimensions B Insulation — Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating — –20°C to +105°C Flammability — UL: VW1 C Part Number 22 AWG 7/30 Tinned Copper 2 0.156 [3.96] 0.312 [7.92] 5 0.624 [15.85] 0.780 [19.81] 10 1.404 [35.66] 1.560 [39.62] 15 2.184 [55.47] 2.340 [59.44] 20 2.964 [75.29] 3.120 [79.25] 24 3.588 [91.14] 3.744 [95.10] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 0.051 [1.30] 02WGY00008P 05WGY00008P 10WGY00008P 15WGY00008P 20WGY00008P 24WGY00008P 18 AWG 7/26 Tinned Copper 2 0.156 [3.96] 0.312 [7.92] 5 0.624 [15.85] 0.780 [19.81] 10 1.404 [35.66] 1.560 [39.62] 15 2.184 [55.47] 2.340 [59.44] 20 2.964 [75.29] 3.120 [79.25] 24 3.588 [91.14] 3.744 [95.10] 0.068 [1.73] 0.068 [1.73] 0.068 [1.73] 0.068 [1.73] 0.068 [1.73] 0.068 [1.73] 02WJY000001P 05WJY000010P 10WJY000010P 15WJY000010P 20WJY000010P 24WJY000010P Other Conductor Counts Available on Request. Contact MADISON CABLE (1-877-MADISON), a division of TE Connectivity, for engineering questions or for order placement of this cable. PAGE 55 MTA, CST-100 II and SL-156 Connectors Prepared IDC Ribbon Cable In addition to bulk cable, the US Engineering Cable Assembly Group offers Prepared Cable for the .100 [2.54] and .156 [3.96] centerline cables. This can be in the form of prenotched cable on reels or cut-to-length cable segments. Prenotched 250 foot reels of cable can be produced with notches at varying increments or repeating all along the cable. The maximum width of these cables is 20 conductor for the .100 [2.54] centerline and 13 conductor for the .156 [3.96] centerline. Prepared Cable is also available with a Strip and Retain feature allowing the PAGE 56 cable assembly to be soldered directly to the PC Board. This saves space and cost and reduces spare parts inventory. Strip and Retain on both ends is used in family board applications to maintain the electrical connection when the PC Board is separated into smaller boards after soldering. Widths are limited to 20 conductors for the .100 [2.54] centerline and 13 conductors for the .156 [3.96] centerline. However, multiple cables can be placed side-byside in a single connector. For other styles and configurations contact the product engineer or product manager. MTA, CST-100 II and SL-156 Connectors MTA Wire Termination Flowchart Choose the appropriate MTA Connector from the MTA Catalog 82056. Select the proper wire style and AWG for the chosen MTA Connector (Refer to pages 59-63). Choose the MTA Termination Tooling (Refer to pages 55-61). Terminate the Wire-to-MTA Connector per Application Tooling Instruction Sheet. Inspect the MTA Wire Termination per Application Specification, especially the wire depth. See illustrations: 114-13072—MTA-50 Connectors, 114-1019—MTA-100 Connectors, 114-102 0 — MTA-156 Connectors, Posted Connector, Card Edge, 114-1048 — MTA-156 Quad Connectors, 114-1031 — MTA-100 Ribbon Cable Connector Assembly, and 114-1032—MTA-156 Ribbon Cable Connector Assembly. B Min. Top of Contact Conductor Bare wires will not be visible beyond back of housing A Centerline of Conductor Bare wires will not extend above top of contact Back of Housing Insulation Strain Relief Conductor Insulation will be contained within the confines of the insulation strain relief as indicated Connector A B .069–.087 .040 MTA-100 [1.75-2.21] [1.02] .090–.113 .060 MTA-156 [2.29-2.87] [1.52] Adjust the Termination Tooling (if needed) per Tooling Instruction Sheet (repeat the step above). PAGE 57 MTA, CST-100 II and SL-156 Connectors MTA Application Tooling Options One-At-A-Time Termination Tooling Part Numbers Interchangeable Head and Interchangeable Head Loose-Piece Feed Track MTA Connector Manual Hand Tool 58074-1 Air Bench Mount Air Hand Tool 58075-1 Assembly Tool 58338-1 Air Bench Mount Tool 58338-1 Electric Bench Electric Bench Machine 931800-1 Machine 931800-1 MTA-50 Closed End Feed Thru — 58246-1 (Standard)* n 58246-2 (Ext Wear) * 58246-3 (Ribbon Cable) 58442-1 Closed End MTA-100 Connector Feed Thru Posted (Closed-End) 58247-1 (Standard)** 58247-2 (Ext Wear) 58247-3 (Ribbon Cable) 58443-1 Closed End MTA-156 Connector Feed Thru Posted (Closed-End) MTA-156 Closed Card-Edge End MTA-156 Closed Quad End *Repair Kit 856600-1 58638-1 Note: Max. Insulation Outside Diameter Wire: .060 [1.52] for MTA-100 Connectors /.095 [2.41] for MTA-156 Connectors Interchangeable Head and Tape Feed Track — 933567-1 — 58575-1 — 58575-1 58635-1 58575-1 58636-1 58575-1 58009-2 58010-2 58244-1 58244-3 58245-1 58245-3 — — — 59803-1 — — — 59803-1 933568-1 853547-1 & 853542-1 (Base) PAGE 58 466727-1 59804-1 — — 59804-1 58082-1 — — — 59804-1 58061-1 — — 58392-1 — — Interchangeable Head and Tape Feed Track Part Number Used With 854175-1 & 312522-1 854200-1 (Base) Manual Bench Tool 58024-1 and Tooling Assembly 58039-1 — 58576-1 — — — — — — — 854176-1 & 312522-1 854200-1 (Base) Manual Bench Tool 58024-1 58576-1 and Tooling Assembly 58040-1 58576-1 — — — — — — — — — — 58576-1 Manual Bench — Tool 58024-1 58576-1 and Tooling Assy 58040-1 58024-1 and — Tooling Assy 58576-1 58040-1 2- through 12-positions.†† 2- through 8-positions. † 59803-1 567020-1 — 59839-1 59804-1 **Repair Kit 856600-2 58242-1 58242-3 58243-1 58243-3 58245-3 466728-1 — — Harness Board Holding Fixture Used With Part Number Applicator Tooling Assembly Assembly 58244-3 58245-1 — 853546-1 & 853542-1 (Base) MTA-100 and MTA-156 Mass Termination Tooling Part Numbers 58244-1 T-Handle MainteSpecial Applicator nance Tool Air Bench Mount Tool 58338-1 Electric Bench Machine 931800-1 Notes: 1. A repair kit consists of a cam, a feed-slide sub-assembly and a locating pawl. Repair kits can be made available for other interchangeable heads. Consult TE. 2. Standard modular heads 58246-1 and 58247-1 are recommended for low volume use. 3. Extended wear modular heads 58246-2 and 58247-2 are recommended for high volume use. 4. T-Handle Maintenance Tools are for maintenance (field) use only. They are not recommended for production. 5. Some Manual Hand Tool Assemblies are available: a. Order 58579-1, comprised of Head 58246-1 with Manual Hand Tool 58074-1. b. Order 58580-1, comprised of Head 58247-1 with Manual Hand Tool 58074-1. c. Order 58639-1, comprised of Head 58638-1 with Manual Hand Tool 58074-1. Note: Max. Insulation Outside Diameter Wire: .050 [1.27] for MTA-100 Connectors /.070 [1.78] for MTA-156 Connectors MTA, CST-100 II and SL-156 Connectors MTA Application Tooling Options (Continued) One-At-A-Time Termination Tooling (Typical Tooling Combinations) Manual Hand Tool with Interchangeable Head Air Hand Tool with Interchangeable Head Air Bench Mount Tool with Interchangeable Head and Foot Switch Electric Bench Machine with Interchangeable Head Air Hand Tool — Pistol Grip Pneumatic Handle Part No. 58075-1 Air Bench Mount Tool — Bench Mount Power Assembly Part No. 58338-1 Electric Bench Machine — IDC Power Unit Part No. 931800-1 • Light weight • Operates at air pressure between 40 and 70 psi [2.76 and 4.83 bar] • Head may be rotated for user convenience • May be mounted with interchangeable head pointed up or down • Operated by a foot switch • Operates at air pressure between 40 and 70 psi [2.76 and 4.83 bar] • All electric: 120 VAC, 60 Hz, 2 A • Compact, portable and quiet • Operated by a foot switch Power Units Manual Hand Tool — Pistol Grip Handle Part No. 58074-1 • Easy to use • Ratchet control will not release the trigger until it is fully bottomed • Head may be rotated for user convenience Air Bench Mount Tool with Interchangeable Head and Loose-Piece Feed Track Electric Bench Machine with Interchangeable Head and Tape Feed Track Interchangeable Heads and Applicators (Refer to page 58 for part numbers.) Interchangeable Head • Terminates one unstripped wire per cycle • Aligns and holds the connector in place for each termination • Automatically advances the connector after each termination Interchangeable Head and Loose-Piece Feed Track • No special setup required • Connectors are easily loaded into feed track • Connectors are fed using a simple spring-loaded pusher T-Handle Maintenance Tool PAGE 59 Special Applicator • Connectors are easily hand loaded into feed • No special setup required track • Tape-mounted connectors • Automatically advances are transferred from prodthe connector after each uct reel to feed track by termination simply pulling on the free • Cannot be cycled until end of the carrier tape the connector is properly • Connectors are fed using positioned a simple spring-loaded pusher Interchangeable Head and Tape Feed Track MTA, CST-100 II and SL-156 Connectors MTA Application Tooling Options (Continued) Mass Termination Tooling (Typical Tooling Combinations) Manual Bench Tool with Applicator and Holding Fixture Air Harness Tool with Applicator 2700 lb Air Bench Machine with Ribbon Cable Notcher Assembly Power Units Manual Bench Tool — Arbor Frame Assembly Part No. 58024-1 • Applicator and holding fixture can be oriented for operator convenience for closed-end or feed-thru terminations • Ram height (insertion depth) is easily adjusted • May be bench mounted 2700 lb Air Bench Machine — Part No. 312522-1 Air Harness Tools — Hand-Held Power Unit with Applicator Part No. 58575-1 (MTA-100) Part No. 58576-1 (MTA-156) • Operated by a foot switch • Capable of exerting 2,700 lb [12,000 N] of force at minimum 80 psi [5.52 bar] air pressure • Applicator can be rotated 360° for orientation with holding fixture • Insertion depth is easily adjusted • Operates at air pressure between 75 and 95 psi [5.17 and 6.55 bar] • May be bench mounted Applicators and Notcher Assemblies Ribbon Cable Notcher Assembly Manual Bench Tool with Applicator and Tape Feed Track Applicator and Holding Fixture • Wires are laced into plastic combs for mass termination • Trims excess wire for closed-end terminations • Holding fixture may be mounted to a harness board Applicator and Tape Feed Track • Tape-mounted connectors are transferred from product reel to feed track by simply pulling on the free end of the carrier tape • Connectors are fed using a simple spring-loaded pusher • Feed stop easily adjusted for different connector sizes • Notch cable with up to 28 conductors for .100 centerline, and 24 conductors for .156 centerline • Pressure plate holds cable in position during notching • Scrap conveniently removed through a chute with a blast of air from a built-in air valve Part Number Wire Size AWG 854449-2 26-28 854449-4 22-28 854449-3 18-24 Centerline Ribbon Cable Notcher Assembly Used With .100 2.54 .100 2.54 Manual Bench Tool 58024-1 Air Bench Machine 91112-2 2700 lb Bench Machine 312522-1 .156 AMP-O-LECTRIC 3.96 Bench Machine 1-471273-3 (with Conversion Kit 690675-2) Use Adapter 854468-1 when putting Notcher in the AMP-O-LECTRIC Machine. Use Adapter 854468-2 when putting Notcher in the 2700 lb Air Bench Machine. PAGE 60 MTA, CST-100 II and SL-156 Connectors Typical Application Rates Produce 6-in. [15 cm] Long Jumpers, One 4-Position MTA-100 Connector per End, Discrete Wire Method Terminations Per Hour Manual Hand Tool 58074-1 with — Interchangeable Head 58246-1 Electric Bench Machine 931800-1 with 900 Interchangeable Head 58246-1 Electric Bench Machine 931800-1 with 1,100 Interchangeable Head and Loose-Piece Feed Track 933567-1 Electric Bench Machine 931800-1 with Interchangeable Head and Tape Feed 1,250 Track 853546-1 and 853542-1 (Base) Produce 6-in. [15 cm] Long Jumpers, One 4-Position MTA-100 Connector per End, Ribbon Cable* Terminations Per Hour 2700 lb Air Bench Machine 312522-1 with 7,500 Applicator and Tape Feed Track 854175-1 and 854200-1 (Base) Method * Procedure: Mass terminate 12-conductor ribbon cable with three connectors per end. After terminating, separate by tearing the 12-conductor assembly into three 4-conductor assemblies. Cable Notching Cable Ends Per Hour 2700 lb Air Bench Machine 312522-1 with 1,000 Ribbon Cable Notcher Assembly 854449-2 and 854468-2 (Adapter) Method Apply One 4-Position MTA-100 Feed-Thru Connector per Assembly, Discrete Wire Method Manual Bench Tool 58024-1 with Applicator and Holding Fixture Terminations Per Hour 650 For further information about tooling call Technical Support. PAGE 61 MTA, CST-100 II and SL-156 Connectors Part Number Index Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. 02WEY00007P 02WEY00008P 02WFY00006P 02WFY00007P 02WGY00001P 02WGY00008P 02WJY000001P 05WEY00004P 05WEY00007P 05WFY00006P 05WFY00007P 05WGY00006P 05WGY00008P 05WJY000010P 10WEY00007P 10WEY00012P 10WFY00006P 10WFY00007P 10WGY00002P 10WGY00008P 10WJY000010P 15WEY00002P 15WEY00007P 15WFY00006P 15WFY00007P 15WGY00006P 15WGY00008P 15WJY000010P 20WEY00007P 20WEY00008P 20WFY00006P 20WFY00007P 20WGY00006P 20WGY00008P 20WJY000010P 24WGY00008P 24WJY000010P 25WEY00007P 25WEY00008P 25WFY00006P 25WFY00007P 25WGY00006P 28WEY00007P 28WEY00008P 28WFY00006P 28WFY00007P 28WGY00006P 57034 57040 350980 640250 640251 640252 640383 640384 640385 640387 640388 PAGE 62 Page 61 61 61 61 61 62 62 61 61 61 61 61 62 62 61 61 61 61 61 62 62 61 61 61 61 61 62 62 61 61 61 61 61 62 62 62 62 61 61 61 61 61 61 61 61 61 61 60 60 48, 49 49 49 48, 49 39 39 40 42 41 Part No. 640389 640426 640427 640428 640429 640430 640431 640432 640433 640434 640435 640440 640441 640442 640443 640445 640452 640453 640454 640455 640456 640457 640468 640469 640470 640471 640472 640473 640474 640477 640480 640550 640551 640556 640557 640558 640559 640595 640599 640600 640601 640602 640604 640605 640606 640607 640608 640620 640621 640622 640623 640629 640630 640631 640632 640633 640634 640635 640636 640637 640638 640639 Page 42 30 30 30 30 30 30 30 30 30 30 8 8 8 8 41 14 14 16 16 17 17 8 8 8 8 30 30 30 30 30 9 33 34 34 34 34 32 32 32 32 32 32 32 32 32 32 8 8 8 8 35 35 34 34 34 34 34 10 10 10 10 Part No. 640642 640643 640706 640707 640708 640709 641113 641119 641120 641121 641122 641123 641124 641125 641126 641127 641143 641144 641145 641146 641147 641148 641149 641150 641151 641152 641153 641154 641155 641156 641157 641168 641170 641175 641186 641187 641188 641189 641190 641191 641192 641193 641198 641199 641200 641201 641202 641203 641204 641207 641208 641209 641210 641211 641212 641213 641214 641215 641216 641217 641218 641219 Page 9 33 48 48 10 10 39 41 41 42 14 14 16 16 17 17 34 34 34 34 34 30 30 30 30 30 30 30 30 30 30 32 32 32 10 10 10 10 8 8 8 8 8 8 8 8 39 39 40 42 41 41 42 14 14 16 16 17 17 31 31 31 Part No. 641220 641221 641222 641223 641224 641225 641226 641231 641232 641233 641234 641235 641236 641237 641238 641239 641240 641241 641242 641243 641244 641302 641311 641312 641313 641314 641425 641426 641427 641428 641429 641435 641436 641437 641438 641439 641440 641522 641523 641524 641525 641526 641533 641534 641535 641536 641537 641550 641623 641643 641644 641645 641646 641653 641654 641655 641656 641994 643067 643071 643075 643077 Page 31 31 31 31 31 31 31 32 32 32 32 32 32 8 8 8 8 8 8 8 8 32 8 8 8 8 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 38 35 8 8 8 8 48 35 9 9 9 9 8 8 8 8 10 33 33 9 9 MTA, CST-100 II and SL-156 Connectors Part Number Index (Continued) Part No. 643498 643813 643814 643815 643816 643817 643818 643819 643820 643821 643828 Page 8 8 8 8 8 30 30 30 30 30 8 643995 644020 644038 644040 644042 644043 644044 644082 644083 644284 644312 644313 644456 644457 644460 644461 644462 644463 644464 644465 644466 644467 644468 644469 644470 644471 644486 644487 644488 644489 644497 644501 644502 644511 644512 644513 644514 644540 644563 644564 644565 644566 644570 644574 644575 644576 644577 644578 644579 644611 644613 38 8 8 8 8 8 8 30 8 30 8 8 15 15 30 30 30 30 30 32 32 32 32 32 32 32 23 23 23 23 8 30 30 8 8 8 8 8 8 8 8 30 30 8 8 8 8 8 8 43 44 PAGE 63 Part No. 644615 Page 43 644617 644631 644633 644662 644663 644687 644694 644695 644702 644718 644720 644726 644749 644750 644751 644752 644753 644754 644755 644756 644759 644760 644761 644763 644766 644767 644768 644769 644783 644791 644795 644803 644807 644809 644812 644814 644860 644861 644874 644875 644876 644877 644878 644884 644885 644886 644887 644888 644889 644890 644891 644892 644893 644894 644896 644897 644898 647000 647001 647002 647003 44 43 44 30 30 30 15 15 8 32 32 8 39 39 40 41 41 42 42 39 41 41 42 39 41 41 42 42 30 30 8 23 38 38 38 38 30 23 17 17 16 16 30 15 15 15 15 15 15 15 15 25 25 25 25 25 25 13 13 13 13 Part No. 647004 647005 647006 647007 647008 647009 647010 647011 647012 647013 647014 647015 647016 647017 647018 647019 647020 647021 647022 647023 647030 647031 647032 647033 647047 647048 647050 647051 647075 647076 647078 647079 647106 647107 647108 647109 647114 647116 647117 647123 647125 647127 647166 647167 647168 647295 647296 647297 647298 647299 647300 647400 647401 647402 647406 647409 647466 647476 647477 647478 647479 647480 Page 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 20 20 21 21 20 20 21 21 22 22 22 20 20 21 21 46 46 46 22 22 22 21 21 21 20 20 20 51 51 51 51 51 51 38 8 30 32 8 Part No. Page 647481 647485 647496 647497 647609 647623 647624 647625 647626 647627 647628 647629 647630 647646 647648 647649 647651 647652 647653 770258 770476 770522 770849 770894 971111 1375819 1375820 1445336 1744017 1744020 38 51 32 38 17 17 17 17 17 17 19 19 19 40 45 45 19 19 19 48 48, 51 48 49 50 53 24 24 24 41 8 MTA, CST-100 II and SL-156 Connectors Application Tooling Part Number Index Part No. 58009 58010 58024 58039 58040 58061 58074 58075 58082 58242 58243 58244 58245 58246 58247 58338 58392 58442 58443 PAGE 64 Page 58, 61 58, 61 58, 60, 61 58, 61 58, 61 58, 61 58, 60, 61 58, 59 58, 61 58, 61 58, 61 58, 61 58, 61 58, 61 58, 61 58, 60, 61 58, 61 58, 61 58, 61 Part No. 58517 58575 58576 58579 58614 58635 58636 58638 58639 58644 58646 59803 59804 59836 59837 59839 59845 59848 90471 Page 24 58, 60, 61 58, 60, 61 58 48 58, 61 58, 61 58, 61 58 58, 61 58, 61 58, 61 58, 61 10 34 58 61 47, 50 48 Part No. Page Part No. Page 91112 312522 354500 466468 466727 466728 466747 466947 471273 567020 567373 567827 567828 567910 680211 690675 853542 853546 60, 61 58, 60, 61 61 48 58, 61 58, 61 10 48 60, 61 58, 61 24 24 48 24 48 60, 61 58, 61 58, 61 854175 854176 854200 854449 854468 856600 931800 933567 933568 1583503 1583514 1583515 1583516 1583517 1583518 58, 61 58, 61 58, 61 60 60, 61 58, 61 58, 60, 61 58, 61 58, 61 58, 61 58, 61 58, 61 58, 61 58, 61 58, 61 853547 58, 61 MTA, CST-100 II and SL-156 Connectors Global Contacts Americas Argentina – Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2211 Brasil – São Paulo Phone: +55-11-2103-6000 Fax: +55-11-2103-6030 Canada – Toronto Phone: +905-475-6222 Fax: +905-474-5520 Product Information Center: Phone: +905-470-4425 Fax: +905-474-5525 Chile – Santiago Phone: +56-2-345-0361 Fax: +56-2-223-1477 Colombia – Bogota Phone: +57-1-319-8959 Fax: +57-1-319-8960 Mexico – Mexico City Phone: +52-55-1106-0800 +01-800-733-8926 Fax: +52-55-1106-0901 For Latin/South American Countries not shown Phone: +54-11-4733-2015 Fax: +54-11-4733-2083 United States Harrisburg, PA Phone: +1-717-564-0100 Fax: +1-717-986-7575 Product Information Center: Phone: +1-800-522-6752 Fax: +1-717-986-7575 Troy, MI Phone: +1-248-273-3359 Fax: +1-248-273-3322 Asia/Pacific Australia – Sydney Phone: +61-2-9554-2600 Fax: +61-2-9502-2556 Product Information Center: Phone: +61-2-9840-8200 Fax: +61-2-9634-6188 Japan – Kawasaki, Kanagawa Phone: +81-44-844-8111 Fax: +81-44-812-3207 Product Information Center: Phone: +81-44-844-8013 Fax: +81-44-812-3200 India – Bangalore Phone: +91-80-285-40800 Fax: +91-80-285-40820 Korea – Seoul Phone: +82-2-3415-4500 Fax: +82-2-3486-3810 Indonesia – Jakarta Phone: +65-6482-0311 Fax: +65-6482-1012 Malaysia – Selangor Phone: +60-3-7805-3055 Fax: +60-3-7805-3066 New Zealand – Auckland Phone: +64-9-634-4580 Fax: +64-9-634-4586 Singapore – Singapore Phone: +65-6482-0311 Fax: +65-6482-1012 Philippines – Makati City Phone: +632-848-0171 Fax: +632-867-8661 Taiwan – Taipei Phone: +886-2-8768-2788 Fax: +886-2-8768-2268 People’s Republic of China Hong Kong Phone: +852-2735-1628 Fax: +852-2735-0243 Thailand – Bangkok Phone: +66-2-955-0500 Fax: +66-2-955-0505 Shanghai Phone: +86-21-2407-1588 Fax: +86-21-2407-1599 Vietnam – Ho Chi Minh City Phone: +84-8-930-5546 Fax: +84-8-930-3443 Europe/Middle East /Africa Austria – Vienna Phone: +43-1-905-60-0 Fax: +43-1-905-60-1333 Product Information Center: Phone: +43-1-905-60-1249 Fax: +43-1-905-60-1251 France – Cergy-Pontoise Cedex Phone: +33-1-3420-8888 Fax: +33-1-3420-8600 Product Information Center: Phone: +33-1-3420-8686 Fax: +33-1-3420-8623 Belarus – Minsk Phone: +375 17 237 47 94 Fax: +375 17 237 47 94 France Export Divisions – Cergy-Pontoise Cedex Phone: +33-1-3420-8804 Fax: +33-1-3420-8699 Belgium – Kessel-Lo Phone: +32-16-352-300 Fax: +32-16-352-355 Bulgaria – Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153 Czech Republic and Slovakia Czech Republic – Kurim Phone: +420-541-162-111 Fax: +420-541-162-223 Product Information Center: Phone: +420-541-162-113 Fax: +420-541-162-132 Denmark – Glostrup Phone: +45-43-48-04-00 Fax: +45-43-44-14-14 Egypt – Cairo Phone: +202-419-2334 Fax: +202-417-7647 Estonia – Tartu Phone: +372-5138-274 Fax: +372-7400-779 Finland – Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250 PAGE 65 Germany – Bensheim Phone: +49-6251-133-0 Fax: +49-6251-133-1600 Product Information Center: Phone: +49-6251-133-1999 Fax: +49-6251-133-1988 Greece – Athens Phone: +30-210-9370-396/397 Fax: +30-210-9370-655 Hungary – Budapest Phone: +36-1-289-1000 Fax: +36-1-289-1010 Product Information Center: Phone: +36-1-289-1016 Fax: +36-1-289-1017 Ireland – Dublin Phone: +353-1-866-5612 Fax: +353-1-866-5714 Israel – Petach-Tikva Phone: +972-3-929-0999 Fax: +972-3-919-1088 Italy – Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031-116 Product Information Center: Phone: +39-011-4012-428 Fax: +39-011-40-287-428 Lithuania and Latvia Lithuania – Vilnius Phone: +370-5-213-1402 Fax: +370-5-213-1403 Product Information Center: Phone: +370-5-211-3016 Fax: +370-5-213-1403 South Africa – Port Elizabeth Phone: +27-41-503-4500 Fax: +27-41-581-0440 Netherlands – ’s-Hertogenbosch Phone: +31-73-6246-246 +31-73-6212-365 Fax: Product Information Center: Phone: +31-73-6246-999 Fax: +31-73-6246-998 Sweden – Upplands Väsby Phone: +46-8-50-72-50-00 Fax: +46-8-50-72-50-01 Norway – Nesbru Phone: +47-66-77-88-50 Fax: +47-66-77-88-55 Poland – Warsaw Phone: +48-22-4576-700 Fax: +48-22-4576-720 Product Information Center: Phone: +48-22-4576-704 Fax: +48-22-4576-720 Romania – Bucharest Phone: +40-21-311-3479/3596 Fax: +40-21-312-0574 Russia – Moscow Phone: +7-495-790-7902 Fax: +7-495-721-1893 Product Information Center: Phone: +7-495-790-7902-404 Fax: +7-495-790-7902-401 Russia – St. Petersburg Phone: +7-812-718-8192 Fax: +7-812-718-8193 Slovenia – Ljubljana Phone: +386-1561-3270 Fax: +386-1561-3240 Spain – Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879 Switzerland – Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444 Turkey – Istanbul Phone: +90-212-281-8181/2/3 +90-212-282-5130/5430 Fax: +90-212-281-8184 Ukraine – Kiev Phone: +380-44-206-2265 Fax: +380-44-206-2264 Product Information Center: Phone: +380-44-206-2265 Fax: +380-44-206-2264 United Kingdom – Stanmore, Middlesex Phone: +44-8706-080208 Fax: +44-208-954-6234 Product Information Center: Freephone (UK only): +0800-267-666 Phone: +44-8706-080208 Fax: +44-208-420-8095 TE TECHNICAL SUPPORT CENTER USA: +1 (800) 522-6752 Canada: +1 (905) 475-6222 Mexico: +52 (0) 55-1106-0800 Latin/S. America: +54 (0) 11-4733-2200 Germany: +49 (0) 6251-133-1999 UK: +44 (0) 800-267666 France: +33 (0) 1-3420-8686 Netherlands: +31 (0) 73-6246-999 China: +86 (0) 400-820-6015 te.com TE Connectivity, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2017 TE Connectivity Ltd. family of companies All Rights Reserved. 82056  09/20  Revised APPLIANCES /// MTA, CST-100 II AND SL-156 CONNECTORS