1055868-1

Instruction Sheet 408-8676 Production Torque Wrenches 10 MAR 11 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. Torque Wrench Open-End Wrench Head TYCO ELECTRONICS PART NUMBER PREVIOUS PART NUMBER 1055276-1 2098-0351-54 1055419-1 Protective Cover WRENCH SIZE mm INCHES ([ ]) PRESET TORQUE Production Torque Wrench 6.4 1/4 18 in-lbs. 2098-5065-54 For SMA (OSM) Type Connectors 7.9 5/16 8 in.-lbs. 1055840-1 2098-5304-54 For OSSM Type Connectors 6.4 1/4 5 in.-lbs 1055512-1 2098-5619-54 For SMA (OSM) Hermetic Type Connectors 7.1 9/32 30 in.-lbs. 1055546-1 2098-5830-54 Production Torque Wrench Kit 6.4 and 8.0 1/4 and 5/16 8 in.-lbs. 1055790-1 2598-5026-54 For SC/N Type Connectors (Hex Nut Design) 20.6 13/16 14 in.-lbs. 1055791-1 2598-5027-54 For TNC Type Connectors (Hex Nut Design) 15.9 5/8 14 in.-lbs. 1055826-1 2598-5160-54 Production Torque Wrench 4.0 5/32 8 in.-lbs 1055868-1 2598-5298-54 For TNC Type Connectors (Hex Nut Design) 14.3 9/16 14 in.-lbs. 1061789-1 7098-5031-54 For 7mm Type Connectors 19.1 3/4 14 in.-lbs. 1490262-1 2598-5383-50 Production Torque Wrench 7.9 5/16 15 in.-lbs WRENCH DESCRIPTION Figure 1 1. INTRODUCTION 2. DESCRIPTION These production torque wrenches are used to properly install or disassemble the connectors listed in Figure 1. Each production torque wrench contains a protective cover, a torque wrench, and an interchangeable head. Figure 1 also contains the Tyco Electronics part numbers for the wrenches, the previous part numbers for the wrenches, wrench size, and the preset torque for each wrench. NOTE i Dimensions on this sheet are in metric units [with U.S. customary units in brackets], unless otherwise noted. Reason for revision is provided in Section 5, REVISION SUMMARY. Refer to Figure 2 for the appropriate replacement wrench head part numbers. The wrenches are designed to be used in the clockwise or counterclockwise direction. 3. OPERATION OF THE WRENCHES NOTE i If a wrench has not been used recently, move the wrench head back and forth several times, listening for audible "clicks." Clicking the wrench head back and forth spreads lubricant throughout the internal mechanism to improve wrench performance. ©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 All Rights Reserved TE logo is a trademark. *Trademark. Other products, logos, and company names might be trademarks of their respective owners. This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com 1 of 2 LOC B 408-8676 Using the appropriate sized head (Figure 1), turn the wrench clockwise (or counterclockwise) until there is an audible "click." This "click" indicates that the proper torque has been achieved. CAUTION Do NOT overtighten the connector with the torque wrench. Over-tightening the wrench could result in inaccurate torque settings. ! CAUTION Do not use or re-terminate damaged connectors. ! 4. REPLACEMENT Remove the wrench head by pulling it off the production torque wrench. Then replace the head with the appropriate head listed in Figure 2. Order replacement parts through your Tyco Electronics Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-9867605, or write to: Figure 2 CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 5. REVISION SUMMARY Since the previous release of this document, the TE logo has been applied. Rev E 2 of 2